Home › ENGINE › 3MZ-FE ENGINE CONTROL SYSTEM › SFI SYSTEM

DTC    P2111    Throttle Actuator Control System - Stuck Open

DTC    P2112    Throttle Actuator Control System - Stuck Closed

for Preparation Click here


SYSTEM DESCRIPTION

The throttle actuator is operated by the ECM (included in the hybrid vehicle control ECU), and opens and closes the throttle valve using an electric motor and gears. The opening angle of the throttle valve is detected by the Throttle Position sensor, which is mounted on the throttle body. The throttle position sensor provides feedback to the ECM in order that it can control the throttle actuator, and therefore the throttle valve, appropriately in response to driver inputs.

HINT:
This ETCS (Electronic Throttle Control System) does not use a throttle cable.


DTC No.
DTC Detection Condition
Trouble Area
P2111
ECM (included in the hybrid vehicle vehicle control ECU) signals throttle actuator to close, but stuck open
(1 trip detection logic)
  1. Throttle actuator
  2. Throttle body
  3. Throttle valve
P2112
ECM (included in the hybrid vehicle control ECU) signals throttle actuator to open, but stuck closed
(1 trip detection logic)
  1. Throttle actuator
  2. Throttle body
  3. Throttle valve

MONITOR DESCRIPTION

The ECM (included in the hybrid vehicle control ECU) determines that there is a malfunction in the ETCS when the throttle valve remains at a fixed angle despite a high drive current from the ECM. The ECM illuminates the MIL and sets a DTC.
If the malfunction is not repaired successfully, a DTC is set when the accelerator pedal is fully depressed and released quickly (to fully open and close the throttle valve) after the engine is next started.

MONITOR STRATEGY


Related DTCs
P2111: Throttle actuator stuck open
P2112: Throttle actuator stuck closed
Required Sensors/Components (Main)
Throttle actuator
Required Sensors/Components (Related)
-
Frequency of Operation
Continuous
Duration
0.5 seconds
MIL Operation
Immediate
Sequence of Operation
None

TYPICAL ENABLING CONDITIONS


All: 
Monitor runs whenever following DTCs are not present
None

P2111 (Throttle actuator stuck open): 
All of the following conditions are met
-
System guard*
ON
Throttle actuator current
2 A or more
Duty cycle to close throttle
80% or more
* System guard is set when the following conditions are met
-
Throttle actuator
ON
Throttle actuator duty calculation
Executing
Throttle position sensor
Fail determined
Throttle actuator current-cut operation
Not executing
Throttle actuator power supply
4 V or more
Throttle actuator
Fail determined

P2112 (Throttle actuator stuck closed): 
All of the following conditions are met
-
System guard*
ON
Throttle actuator current
2 A or more
Duty cycle to open throttle
80% or more
* System guard is ON when the following conditions are met
-
Throttle actuator
ON
Throttle actuator duty calculation
Executing
Throttle position sensor
Fail determined
Throttle actuator current-cut operation
Not executing
Throttle actuator power supply
4 V or more
Throttle actuator
Fail determined

TYPICAL MALFUNCTION THRESHOLDS


P2111 (Throttle actuator stuck open): 
TP sensor voltage change
No change

P2112 (Throttle actuator stuck closed): 
TP sensor voltage change
No change

FAIL-SAFE

When either of these DTCs, as well as other DTCs relating to ETCS (Electronic Throttle Control System) malfunctions, is set, the ECM (included in the hybrid vehicle control ECU) enters fail-safe mode. During fail-safe mode, the ECM cuts the current to the throttle actuator off, and the throttle valve is returned to a 6° throttle angle by the return spring. The ECM then adjusts the engine output by controlling the fuel injection (intermittent fuel-cut) and ignition timing, in accordance with the accelerator pedal opening angle, to allow the vehicle to continue at a minimal speed. If the accelerator pedal is depressed firmly and gently, the vehicle can be driven slowly.
Fail-safe mode continues until a pass condition is detected, and the power switch is then turned off.

WIRING DIAGRAM

Refer to DTC P2102 .

INSPECTION PROCEDURE

HINT:
Read freeze frame data using the Techstream. The ECM (included in the hybrid vehicle control ECU) records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can be helpful in determining whether the vehicle was running or stopped, whether the engine was warmed up or not, whether the air fuel ratio was lean or rich, as well as other data recorded at the time of a malfunction.

1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P2111 or P2112)
  1. Connect the Techstream to the DLC3.

  1. Turn the power switch on (IG).

  1. Turn the Techstream on.

  1. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

  1. Read the DTCs.

    Result:

    Display (DTC Output)
    Proceed to
    P2111 or P2112
    A
    P2111 or P2112 and other DTCs
    B

    HINT:
    If any DTCs other than P2111 or P2112 are output, troubleshoot those DTCs first.



B
GO TO DTC CHART
A


2.INSPECT THROTTLE BODY ASSEMBLY (VISUALLY CHECK THROTTLE VALVE)
  1. Check for contamination such as carbon between the throttle valve and the housing. If necessary, clean the throttle body. And check that the throttle valve moves smoothly.

    OK:
    Throttle valve is not contaminated with foreign objects and moves smoothly.



NG
REPLACE THROTTLE BODY ASSEMBLY (Click here)
OK


3.CHECK WHETHER DTC OUTPUT RECURS (DTC P2111 OR P2112)
  1. Connect the Techstream to the DLC3.

  1. Put the engine in inspection mode (Click here).

  1. Turn the Techstream on.

  1. Clear the DTCs (Click here).

  1. Start the engine, and fully depress and release the accelerator pedal quickly (to fully open and close the throttle valve).

  1. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes

  1. Read the DTCs.

    Result:

    Display (DTC Output)
    Proceed to
    No DTC
    A
    P2111 or P2112
    B



B
REPLACE HYBRID VEHICLE CONTROL ECU (Click here)
A

CHECK FOR INTERMITTENT PROBLEMS (Click here)