Home › DRIVE LINE › DRIVE SHAFT › REAR DRIVE SHAFT

REAR DRIVE SHAFT > INSTALLATION

for Preparation Click here



1. INSTALL REAR DRIVE SHAFT ASSEMBLY
  1. Align the matchmarks.



    C108295E02
  1. Install the rear drive shaft assembly with the 4 nuts and washers.

    Torque:
    56 N*m{ 571 kgf*cm , 41 ft.*lbf }



2. INSTALL REAR AXLE CARRIER SUB-ASSEMBLY LH


    C166002
  1. Temporarily install the the rear axle carrier sub-assembly with the 2 bolts and the 2 nuts.

    NOTICE:
    1. Be careful not to damage the rear drive shaft outboard joint boot.
    2. Be careful not to damage the rear speed sensor rotor.
    3. Prevent foreign matter from adhering to the rear speed sensor rotor.
    4. Do not rotate the drive shaft with the rear axle hub and bearing assembly removed.



    C166001
  1. Install the rear axle carrier sub-assembly with the 2 bolts and the 2 nuts.

    Torque:
    290 N*m{ 2956 kgf*cm , 213 ft.*lbf }

    NOTICE:
    1. Be careful not to damage the rear drive shaft outboard joint boot.
    2. Be careful not to damage the rear speed sensor rotor.
    3. Prevent foreign matter from adhering to the rear speed sensor rotor.
    4. Do not rotate the drive shaft with the rear axle hub and bearing assembly removed.

    HINT:
    Insert the bolts from the rear side.



3. TEMPORARILY INSTALL REAR STRUT ROD ASSEMBLY


    C165999E01
  1. Check that the identification mark of the rear strut rod assembly is positioned on the inner side of the vehicle.

  1. Temporarily install the rear strut rod assembly with the 2 bolts and the 2 nuts.

    NOTICE:
    Since stopper nuts are used, temporarily tighten the bolts.



4. INSTALL REAR AXLE HUB AND BEARING ASSEMBLY LH


    C166348E01
  1. Align the matchmarks on the rear drive shaft and rear axle hub.

    NOTICE:
    Do not rotate the drive shaft.



    C165997
  1. Install the parking brake assembly and the rear axle hub and bearing assembly with the 4 bolts.

    Torque:
    75 N*m{ 764 kgf*cm , 55 ft.*lbf }

    NOTICE:
    Do not twist the No. 3 parking brake cable assembly when installing it.



5. INSTALL REAR DISC


    C166438E01
  1. Align the matchmarks and install the rear disc.

    NOTICE:
    When replacing the rear disc with a new one, select the installation position where the rear disc has minimal runout.



6. INSTALL REAR DISC BRAKE CALIPER ASSEMBLY LH


    C165996
  1. Install the rear disc brake caliper assembly with the 2 bolts.

    Torque:
    78 N*m{ 795 kgf*cm , 57 ft.*lbf }



7. INSTALL REAR SPEED SENSOR LH


    C165809
  1. Install the rear speed sensor to the rear axle carrier sub-assembly with the bolt .

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }

    NOTICE:
    1. Keep the rear speed sensor tip and sensor installation hole free from foreign matter.
    2. Do not twist the rear speed sensor wire when installing.



8. STABILIZE SUSPENSION


    C166003E01
  1. Jack up the rear axle carrier sub-assembly, placing a wooden block underneath to avoid damage. Apply load to the suspension so that the rear drive shaft assembly is positioned horizontally.

    CAUTION:
    Do not jack up the rear axle carrier sub-assembly too high as the vehicle may fall.

    NOTICE:
    Do not bend the brake dust cover.

    HINT:
    1. If the rear drive shaft assembly cannot be positioned horizontally as shown in the illustration even when the rear axle carrier sub-assembly is jacked up, apply additional load to the vehicle such as by having a person sit in the rear seat.
    2. Use the same procedure for the RH side and LH side.



9. FULLY TIGHTEN REAR NO. 2 SUSPENSION ARM ASSEMBLY LH


    C166008
  1. Fully tighten the rear No. 2 suspension arm assembly with the bolt and nut.

    Torque:
    112 N*m{ 1141 kgf*cm , 82 ft.*lbf }

    NOTICE:
    1. Since a stopper nut is used, tighten the bolt.
    2. The final torque must be applied under standard vehicle height conditions.



10. FULLY TIGHTEN REAR NO. 1 SUSPENSION ARM ASSEMBLY LH


    C166007
  1. Fully tighten the rear No. 1 suspension arm assembly with the bolt and nut.

    Torque:
    112 N*m{ 1141 kgf*cm , 82 ft.*lbf }

    NOTICE:
    1. Since a stopper nut is used, tighten the bolt.
    2. The final torque must be applied under standard vehicle height conditions.



11. FULLY TIGHTEN REAR STRUT ROD ASSEMBLY


    C166006
  1. Fully tighten the bolt.

    Torque:
    80 N*m{ 815 kgf*cm , 59 ft.*lbf }

    NOTICE:
    1. Since a stopper nut is used, fully tighten the bolt.
    2. The final torque must be applied under standard vehicle height conditions.



    C107672E01
  1. Fully tighten the bolt.

    Torque:
    80 N*m{ 815 kgf*cm , 59 ft.*lbf }

    NOTICE:
    1. Since a stopper nut is used, fully tighten the bolt.
    2. The final torque must be applied under standard vehicle height conditions.



12. INSTALL NO. 3 PARKING BRAKE CABLE ASSEMBLY


    C107671E02
  1. Install the No. 3 parking brake cable assembly with the nut.

    Torque:
    6.0 N*m{ 61 kgf*cm , 53 in.*lbf }

    NOTICE:
    Do not twist the No. 3 parking brake cable assembly when installing it.



13. INSTALL REAR AXLE SHAFT NUT LH
  1. Clean the threaded parts on the drive shaft and axle hub nut using a non-residue solvent.

    NOTICE:
    1. Be sure to perform this work for a new drive shaft.
    2. Keep the threaded parts free of oil and foreign objects.



    C165541
  1. Install a new rear axle shaft nut.

    Torque:
    294 N*m{ 2996 kgf*cm , 216 ft.*lbf }

  1. Using a chisel and hammer, stake the rear axle shaft nut.



14. INSTALL REAR WHEEL

Torque:
103 N*m{ 1050 kgf*cm , 76 ft.*lbf }



15. INSPECT AND ADJUST REAR WHEEL ALIGNMENT

HINT:
(Click here)



16. CHECK ABS SPEED SENSOR SIGNAL

HINT:
(Click here)