Home › BRAKE › BRAKE CONTROL › ELECTRONICALLY CONTROLLED BRAKE SYSTEM

ELECTRONICALLY CONTROLLED BRAKE SYSTEM > TEST MODE PROCEDURE

for Preparation Click here



WARNING LIGHT AND INDICATOR LIGHT INITIAL CHECK
  1. Release the parking brake.

    NOTICE:
    Before releasing the parking brake, move the shift lever to P for safety.

    HINT:
    When the parking brake is applied or the brake fluid level is low, the brake warning light / red (malfunction) comes on.



  2. C193685E01
  3. When the power switch is turned on (IG), check that the ABS warning, brake warning / red (malfunction), brake warning / yellow (minor malfunction) and slip indicator lights come on for approximately 3 seconds.

    HINT:
    1. If the skid control ECU stores any DTCs, the ABS warning, brake warning / red (malfunction), brake warning / yellow (minor malfunction) and slip indicator lights will come on.
    2. The master caution indicator light will come on and a warning message will be displayed on the multi-information display if the EBD system, BA system, or TRAC system is malfunctioning or if the ABS, VSC, electronically controlled brake system control cannot be performed.
    3. If any of the indicators remains on or does not come on, proceed to troubleshooting for the light circuits listed below.

    Trouble Area
    See procedure
    ABS warning light circuit (Remains on)
    Click here
    ABS warning light circuit (Does not come on)
    Click here
    Brake warning light / red (malfunction) circuit (Remains on)
    Click here
    Brake warning light / red (malfunction) circuit circuit (Does not come on)
    Click here
    Brake warning light / yellow (minor malfunction) circuit (Remains on)
    Click here
    Brake warning light / yellow (minor malfunction) circuit circuit (Does not come on)
    Click here
    Slip indicator light circuit (Remains on)
    Click here
    Slip indicator light circuit (Does not come on)
    Click here


SENSOR CHECK USING TEST MODE (SIGNAL CHECK) (When Using the Techstream)

NOTICE:
After replacement of the skid control ECU and/or yaw rate and acceleration sensor, perform zero point calibration of the yaw rate and acceleration sensor.

HINT:
  1. If the power switch is turned from on (IG) to on (ACC) or off during Test Mode (signal check), DTCs recorded during the sensor check will be erased.
  2. During Test Mode (signal check), the skid control ECU records all DTCs detected in the sensor check. By performing Test Mode (signal check), the codes are erased if a normal condition is confirmed. The remaining codes are the codes where an abnormality was found.



  1. Procedure to enter the Test Mode

    1. Turn the power switch off.

    2. Check that the steering wheel is in the straight-ahead position.

    3. Check that the shift lever is in P.

    4. Connect the Techstream to the DLC3.

    5. Turn the power switch on (IG).

    6. Turn the Techstream on.

    7. Switch the skid control ECU to Test Mode using the Techstream. Enter the following menus: Chassis / ABS/VSC/TRAC / Utility / Signal Check.



    8. BR03904E80
    9. Check that the ABS warning, brake warning / yellow (minor malfunction) and slip indicator lights come on for several seconds and then blink in Test Mode.

      HINT:
      If the ABS warning, brake warning / yellow (minor malfunction) and slip indicator lights do not blink, inspect the TS and CG terminal circuit and ABS warning, brake warning / yellow (minor malfunction) and slip indicator light circuits.

    10. Check the ABS sensors.

      HINT:
      Check that the ABS warning light is blinking in the Test Mode blinking pattern before performing the ABS sensor check.

  2. Acceleration Sensor Check

    1. Keep the vehicle stationary on a level surface for 1 second or more.

      HINT:
      The acceleration sensor check can be performed with the master cylinder pressure sensor check below.

  3. Master Cylinder Pressure Sensor Check

    1. Leave the vehicle in a stationary condition and release the brake pedal for 1 second or more, and quickly and continuously depress the brake pedal with a force greater than 98 N (10 kgf, 22 lbf) for 1 second.

    2. Check that the ABS warning light stays on for 3 seconds.

      HINT:
      1. Confirm that the ABS warning light comes on.
      2. While the ABS warning light stays on, continue to depress the brake pedal with a force of 98 N (10 kgf, 22 lbf) or more.
      3. The ABS warning light comes on for 3 seconds every time the preceding brake pedal operation is performed.

  4. Speed Sensor Check

    1. Drive the vehicle straight-ahead.
      Accelerate the vehicle to a speed of 45 km/h (28 mph) or more for several seconds and check that the ABS warning light goes off.

      HINT:
      1. The sensor check may not be completed if wheelspin occurs.
      2. The ABS warning light blinks when the sensor check has been completed and the brake pedal is depressed.
      3. The ABS warning light comes on immediately if a malfunction is detected during the speed sensor check.

    2. Stop the vehicle.

      NOTICE:
      1. Before performing the speed sensor check, complete the acceleration sensor and master cylinder pressure sensor checks.
      2. The speed sensor check may not be completed if the speed sensor check is started while turning the steering wheel or spinning the wheels.
      3. After the ABS warning light goes off, if vehicle speed exceeds 80 km/h (50 mph), a sensor check code will be stored again. Decelerate or stop the vehicle before the speed reaches 80 km/h (50 mph).
      4. If the sensor check has not been completed, the ABS warning light will blink while driving and the ABS will not operate.

      HINT:
      When the sensor check has been completed, the ABS warning light goes off while driving and blinks in the Test Mode pattern while the vehicle is stationary.

    3. Check the VSC sensor.

      HINT:
      Check that the brake warning / yellow (minor malfunction) and slip indicator lights are blinking in the Test Mode blinking pattern before performing the VSC sensor check.



  5. Yaw Rate Sensor Check

    1. Keep the vehicle in a stationary condition on a level surface for 1 second or more.



    2. C137757E03
    3. Move the shift lever from P to D and drive the vehicle at a speed of approximately 5 km/h (3 mph), and turn the steering wheel either to the left or right 90° or more until the vehicle makes a 180° turn.

    4. Stop the vehicle and move the shift lever to P. Check that the skid control buzzer sounds for 3 seconds.

      HINT:
      1. If the skid control buzzer sounds, the sensor check has completed normally.
      2. If the skid control buzzer does not sound, check the skid control buzzer circuit (Click here), then perform the sensor check again.
      3. If the skid control buzzer still does not sound, the yaw rate sensor may be malfunctioning. Check for DTCs.
      4. Make a 180° turn. At the end of the turn, the direction of the vehicle should be within 180° +/-5° of its start position.
      5. Do not allow the wheels to spin.
      6. Do not turn the power switch off while turning.
      7. Do not move the shift lever to P while turning, but changing the vehicle speed, stopping, or driving in reverse is acceptable.
      8. Complete the turn within 20 seconds.



  6. End of Sensor Check



      BR03904E75
    1. If the sensor check is completed, the ABS warning light blinks (Test Mode) when the vehicle is stopped and goes off while the vehicle is driving.

      NOTICE:
      1. When all the yaw rate sensor, acceleration sensor, speed sensor, and master cylinder pressure sensor checks are completed, the sensor check is completed.
      2. If the sensor check is not completed, the ABS warning light will blink even while the vehicle is driving and the ABS will not operate.

  7. Read Sensor Check DTCs

    1. Read the DTC(s) by following the Techstream screen.

      NOTICE:
      1. If only DTCs other than Test Mode sensor check DTCs are displayed, repair the malfunction and clear the DTCs.
      2. If Test Mode sensor check DTCs and other DTCs are displayed or if only Test Mode sensor check DTCs are displayed, repair the malfunction, clear the DTCs, and perform the Test Mode inspection again.

      HINT:
      See "Sensor Check DTCs".

    2. Turn the power switch off and disconnect the Techstream.

  8. Sensor Check DTCs

    ABS Sensor: 
    DTC Code
    Detection Item
    Trouble Area
    C1271
    Low Output Signal of Front Speed Sensor RH
    1. Front speed sensor RH
    2. Sensor installation
    3. Speed sensor rotor
    C1272
    Low Output Signal of Front Speed Sensor LH
    1. Front speed sensor LH
    2. Sensor installation
    3. Speed sensor rotor
    C1273
    Low Output Signal of Rear Speed Sensor RH
    1. Rear speed sensor RH
    2. Sensor installation
    3. Speed sensor rotor
    C1274
    Low Output Signal of Rear Speed Sensor LH
    1. Rear speed sensor LH
    2. Sensor installation
    3. Speed sensor rotor
    C1275
    Abnormal Change in Output Signal of Front Speed Sensor RH
    Speed sensor rotor
    C1276
    Abnormal Change in Output Signal of Front Speed Sensor LH
    Speed sensor rotor
    C1277
    Abnormal Change in Output Signal of Rear Speed Sensor RH
    Speed sensor rotor
    C1278
    Abnormal Change in Output Signal of Rear Speed Sensor LH
    Speed sensor rotor
    C1279
    Acceleration Sensor Output Voltage Malfunction
    1. Sensor installation
    2. Yaw rate and acceleration sensor
    C1281
    Master Cylinder Pressure Sensor Output Malfunction
    1. Stop light switch
    2. Master cylinder pressure sensor

    VSC Sensor: 
    DTC Code
    Detection Item
    Trouble Area
    C0371
    Yaw Rate Sensor
    Yaw rate and acceleration sensor

    Electronically Controlled Brake System Sensor: 
    DTC Code
    Detection Item
    Trouble Area
    C1346
    Stroke Sensor Zero Point Learning Malfunction
    Brake pedal stroke sensor

    HINT:
    The codes in this table are output only in Test Mode (signal check).


SENSOR CHECK USING TEST MODE (SIGNAL CHECK) (When not Using the Techstream)

NOTICE:
After replacement of the skid control ECU and/or yaw rate and acceleration sensor, perform zero point calibration of the yaw rate and acceleration sensor.

HINT:
  1. If the power switch is turned from on (IG) to on (ACC) or off during Test Mode (signal check), DTCs recorded during the sensor check will be erased.
  2. During Test Mode (signal check), the skid control ECU records all DTCs detected in the sensor check. By performing Test Mode (signal check), the codes are erased if a normal condition is confirmed. The remaining codes are the codes where an abnormality was found.



  1. Procedure to enter Test Mode

    1. Turn the power switch off.

    2. Check that the steering wheel is in the straight-ahead position.

    3. Check that the shift lever is in P.



    4. G022987E45
    5. Using SST, connect terminals TS and CG of the DLC3.

      SST
      09843-18040  

    6. Turn the power switch on (IG).



    7. BR03904E80
    8. Check that the ABS warning, brake warning / yellow (minor malfunction) and slip indicator lights come on for several seconds and then blink in Test Mode.

      HINT:
      If the ABS warning, brake warning / yellow (minor malfunction) and slip indicator lights do not blink, inspect the TS and CG terminal circuit and ABS warning, brake warning / yellow (minor malfunction) and slip indicator light circuits.

    9. Check the ABS sensors.

      HINT:
      Check that the ABS warning light is blinking in the Test Mode blinking pattern before performing the ABS sensor check.

  2. Acceleration Sensor Check

    1. Keep the vehicle stationary on a level surface for 1 second or more.

      HINT:
      The acceleration sensor check can be performed with the master cylinder pressure sensor check below.

  3. Master Cylinder Pressure Sensor Check

    1. Leave the vehicle in a stationary condition and release the brake pedal for 1 second or more, and quickly and continuously depress the brake pedal with a force greater than 98 N (10 kgf, 22 lbf) for 1 second.

    2. Check that the ABS warning light stays on for 3 seconds.

      HINT:
      1. Confirm that the ABS warning light comes on.
      2. While the ABS warning light stays on, continue to depress the brake pedal with a force of 98 N (10 kgf, 22 lbf) or more.
      3. The ABS warning light comes on for 3 seconds every time the preceding brake pedal operation is performed.

  4. Speed Sensor Check

    1. Drive the vehicle straight-ahead.
      Accelerate the vehicle to a speed of 45 km/h (28 mph) or more for several seconds and check that the ABS warning light goes off.

      HINT:
      1. The sensor check may not be completed if wheelspin occurs.
      2. The ABS warning light blinks when the sensor check has been completed and the brake pedal is depressed.
      3. The ABS warning light comes on immediately if a malfunction is detected during the speed sensor check.

    2. Stop the vehicle.

      NOTICE:
      1. Before performing the speed sensor check, complete the acceleration sensor and master cylinder pressure sensor checks.
      2. The speed sensor check may not be completed if the speed sensor check is started while turning the steering wheel or spinning the wheels.
      3. After the ABS warning light goes off, if vehicle speed exceeds 80 km/h (50 mph), a sensor check code will be stored again. Decelerate or stop the vehicle before the speed reaches 80 km/h (50 mph).
      4. If the sensor check has not been completed, the ABS warning light will blink while driving and the ABS will not operate.

      HINT:
      When the sensor check has been completed, the ABS warning light goes off while driving and blinks in the Test Mode pattern while the vehicle is stationary.

    3. Check the VSC sensor.

      HINT:
      Check that the brake warning / yellow (minor malfunction) and slip indicator lights are blinking in the Test Mode blinking pattern before performing the VSC sensor check.



  5. Yaw Rate Sensor Check

    1. Keep the vehicle in a stationary condition on a level surface for 1 second or more.



    2. C137757E03
    3. Move the shift lever from P to D and drive the vehicle at a speed of approximately 5 km/h (3 mph), and turn the steering wheel either to the left or right 90° or more until the vehicle makes a 180° turn.

    4. Stop the vehicle and move the shift lever to P. Check that the skid control buzzer sounds for 3 seconds.

      HINT:
      1. If the skid control buzzer sounds, the sensor check has completed normally.
      2. If the skid control buzzer does not sound, check the skid control buzzer circuit (Click here), then perform the sensor check again.
      3. If the skid control buzzer still does not sound, the yaw rate sensor may be malfunctioning. Check for DTCs.
      4. Make a 180° turn. At the end of the turn, the direction of the vehicle should be within 180° +/-5° of its start position.
      5. Do not allow the wheels to spin.
      6. Do not turn the power switch off while turning.
      7. Do not move the shift lever to P while turning, but changing the vehicle speed, stopping, or driving in reverse is acceptable.
      8. Complete the turn within 20 seconds.



  6. End of Sensor Check



      BR03904E75
    1. If the sensor check is completed, the ABS warning light blinks (Test Mode) when the vehicle is stopped and goes off while the vehicle is driving.

      NOTICE:
      1. When the yaw rate sensor, acceleration sensor, speed sensor, and master cylinder pressure sensor checks are completed, the sensor check is completed.
      2. If the sensor check is not completed, the ABS warning light will blink even while the vehicle is driving and the ABS will not operate.



  7. Read Sensor Check DTCs



      G022988E02
    1. Using SST, connect terminals TC and CG of the DLC3.

      SST
      09843-18040  



    2. Count the number of blinks of the ABS warning, brake warning / yellow (minor malfunction) and slip indicator lights.


      C169592E01

      NOTICE:
      1. If only DTCs other than the Test Mode sensor check DTCs are displayed, repair the malfunctions and clear the DTCs.
      2. If Test Mode sensor check DTCs and other DTCs are displayed or if only the Test Mode sensor check DTCs are displayed, repair the malfunctions, clear the DTCs, and perform the Test Mode inspection again.

      HINT:
      1. If more than 1 malfunction is detected at the same time, the lowest numbered code will be displayed first.
      2. See "Sensor Check DTCs".

    3. After performing the check, disconnect SST from terminals TS and CG, and TC and CG of the DLC3 and turn the power switch off.

    4. Turn the power switch on (IG).

      HINT:
      1. If the power switch is not turned on (IG) after SST is removed from the DLC3, the previous Test Mode will continue.
      2. If the power switch is turned on (IG) with terminals TS and CG connected, the previous Test Mode will continue.

  8. Sensor Check DTCs

    ABS Sensor: 
    DTC Code
    Detection Item
    Trouble Area
    71
    Low Output Signal of Front Speed Sensor RH
    1. Front speed sensor RH
    2. Sensor installation
    3. Speed sensor rotor
    72
    Low Output Signal of Front Speed Sensor LH
    1. Front speed sensor LH
    2. Sensor installation
    3. Speed sensor rotor
    73
    Low Output Signal of Rear Speed Sensor RH
    1. Rear speed sensor RH
    2. Sensor installation
    3. Speed sensor rotor
    74
    Low Output Signal of Rear Speed Sensor LH
    1. Rear speed sensor LH
    2. Sensor installation
    3. Speed sensor rotor
    75
    Abnormal Change in Output Signal of Front Speed Sensor RH
    Speed sensor rotor
    76
    Abnormal Change in Output Signal of Front Speed Sensor LH
    Speed sensor rotor
    77
    Abnormal Change in Output Signal of Rear Speed Sensor RH
    Speed sensor rotor
    78
    Abnormal Change in Output Signal of Rear Speed Sensor LH
    Speed sensor rotor
    79
    Acceleration Sensor Output Voltage Malfunction
    1. Sensor installation
    2. Yaw rate and acceleration sensor
    81
    Master Cylinder Pressure Sensor Output Malfunction
    1. Stop light switch
    2. Master cylinder pressure sensor

    VSC Sensor: 
    DTC Code
    Detection Item
    Trouble Area
    71
    Yaw Rate Sensor
    Yaw rate and acceleration sensor

    Electronically Controlled Brake System Sensor: 
    DTC Code
    Detection Item
    Trouble Area
    71
    Stroke Sensor Zero Point Learning Malfunction
    Brake pedal stroke sensor

    HINT:
    The codes in this table are output only in Test Mode (signal check).