Home › ENGINE › 3MZ-FE ENGINE CONTROL SYSTEM › SFI SYSTEM

DTC    P0128    Coolant Thermostat (Coolant Temperature Below Thermostat Regulating Temperature)

for Preparation Click here


DESCRIPTION

This DTC is set when the engine coolant temperature does not reach 75°C (167°F) despite sufficient engine warm-up time.

DTC No.
DTC Detection Condition
Trouble Area
P0128
  1. Conditions (a), (b) and (c) are met for 5 seconds (2 trip detection logic):
    1. (a) Cold start
    2. (b) Engine warmed up
    3. (c) Engine coolant temperature less than 75°C (167°F)
  1. Thermostat
  2. Cooling system
  3. Engine coolant temperature sensor
  4. Hybrid vehicle control ECU

MONITOR DESCRIPTION

The ECM (included in the hybrid vehicle control ECU) estimates the engine coolant temperature based on the starting temperature, engine loads, and engine speeds. The ECM then compares the estimated temperature with the actual engine coolant temperature. When the estimated engine coolant temperature reaches 75°C (167°F), the ECM checks the actual engine coolant temperature. If the actual engine coolant temperature is less than 75°C (167°F), the ECM interprets this as a malfunction in the thermostat or the engine cooling system and sets the DTC.

A082385E32


MONITOR STRATEGY


Related DTCs
P0128: Coolant Thermostat
Required Sensors/Components (Main)
Thermostat
Required Sensors/Components (Related)
Engine coolant temperature sensor, intake air temperature sensor, vehicle speed sensor, mass air flow meter
Frequency of Operation
Once per drive cycle
Duration
900 seconds
MIL Operation
2 driving cycles
Sequence of Operation
None

TYPICAL ENABLING CONDITIONS


Monitor will run whenever this DTC is not present
P0010, P0020 (VVT Oil Control Valve Bank 1, 2)
P0011, P0021 (VVT System 1 - Advance)
P0012, P0022 (VVT System 1 - Retard)
P0031, P0032, P0051, P0052 (Air Fuel Ratio sensor heater - Sensor 1)
P0102, P0103 (Mass Air Flow meter)
P0112, P0113 (Intake Air Temperature sensor)
P0115, P0117, P0118 (Engine Coolant Temperature sensor)
P0120, P0121, P0122, P0123, P0220, P0222, P0223, P2135 (Throttle position sensor)
P0125 (Insufficient Engine Coolant Temperature for Closed Loop)
P0171, P0172, P0174, P0175 (Fuel system)
P0301, P0302, P0303, P0304, P0305, P0306 (Misfire)
P0335 (Crankshaft position sensor)
P0340, P0341, P0345, P0346 (VVT sensor)
P0351, P0352, P0353, P0354, P0355, P0356 (Igniter)
P2195, P2196, P2197, P2198 (Air Fuel Ratio sensor - rationality)
P2237, P2240 (Air fuel ratio sensor - open)
P2238, P2241, P2252, P2255 (Air fuel ratio sensor - low impedance)
P2239, P2242, P2253, P2256 (Air fuel ratio sensor - high impedance)
P2A00, P2A03 (Air Fuel Ratio sensor - slow response)
Battery voltage
11 V or more
Either of following conditions 1 or 2 is met:
-
1. All of following conditions are met:
-
  1. Engine coolant temperature at engine start - intake air temperature at engine start
-15 to 7°C (-27 to 12.6°F)
  1. Engine coolant temperature at engine start
-10 to 56°C (14 to 133°F)
  1. Intake air temperature at engine start
-10 to 56°C (14 to 133°F)
2. All of following conditions are met:
-
  1. Engine coolant temperature at engine start - intake air temperature at engine start
More than 7°C (12.6°F)
  1. Engine coolant temperature at engine start
56°C (133°F) or less
  1. Intake air temperature at engine start
-10°C (14°F) or more
Accumulated time with 128 km/h (80 mph) or more of vehicle speed
Less than 20 seconds

TYPICAL MALFUNCTION THRESHOLDS


Duration that both following conditions (a) and (b) are met
5 seconds or more
(a) Simulated engine coolant temperature
75°C (167°F) or more
(b) Engine coolant temperature sensor output
Below 75°C (167°F)

INSPECTION PROCEDURE

HINT:
Read freeze frame data using the Techstream. The ECM (included in the hybrid vehicle control ECU) records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can be helpful in determining whether the vehicle was running or stopped, whether the engine was warmed up or not, whether the air-fuel ratio was lean or rich, as well as other data recorded at the time of a malfunction.

1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P0128)
  1. Connect the Techstream to the DLC3.

  1. Turn the power switch on (IG).

  1. Turn the Techstream on.

  1. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

  1. Read the DTCs.

    Result:

    Display (DTC Output)
    Proceed to
    P0128
    A
    P0128 and other DTCs
    B

    HINT:
    If any DTC other than P0128 are output, troubleshoot those DTCs first.



B
GO TO DTC CHART
A


2.CHECK COOLING SYSTEM
  1. Check for defects in the cooling system that might cause the system to be too cold, such as abnormal radiator fan operation or any modifications.



NG
REPAIR OR REPLACE COOLING SYSTEM
OK


3.INSPECT THERMOSTAT
  1. Remove the thermostat (Click here).

  1. Check the valve opening temperature of the thermostat.

    Standard:
    80 to 84°C (176 to 183°F)

    HINT:
    In addition to the above check, confirm that the valve is completely closed when the temperature is below the standard.

  1. Reinstall the thermostat (Click here).



NG
REPLACE THERMOSTAT
OK

REPLACE HYBRID VEHICLE CONTROL ECU (Click here)