Home › HYBRID SYSTEM ยท Q211 HYBRID TRANSMISSION / TRANSAXLE › DIFFERENTIAL SIDE GEAR SHAFT

DIFFERENTIAL SIDE GEAR SHAFT > INSTALLATION

for Preparation Click here



1. INSTALL DIFFERENTIAL SIDE GEAR SHAFT SUB-ASSEMBLY
  1. Install a new side gear shaft snap ring.



    C170283E01
  1. Using SST, install the side gear shaft.

    SST
    09520-24010   (09520-04010, 09520-32040)

    NOTICE:
    1. Set the snap ring with the opening facing downward.
    2. Do not tap in the side gear shaft at an angle. If it is installed at an angle, replace the snap ring with a new one and tap in the shaft again.
    3. Do not damage the oil seal.



    C170292E01
  1. Using vernier calipers, measure the distance between the right and left side gear shafts, as shown in the illustration.

    Standard distance:
    272.9 mm (10.744 in.) or less



2. INSTALL REAR DRIVE SHAFT ASSEMBLY
  1. Align the matchmarks.



    C108295E02
  1. Install the rear drive shaft assembly with the 4 nuts and washers.

    Torque:
    56 N*m{ 571 kgf*cm , 41 ft.*lbf }



3. TEMPORARILY TIGHTEN REAR NO. 2 SUSPENSION ARM ASSEMBLY


    C105711
  1. Jack up the rear axle carrier, placing a wooden block to avoid damage.



    C105710
  1. Temporarily tighten the rear No. 2 suspension arm assembly LH with the bolt and nut.

    HINT:
    Insert the bolt from the rear side of the vehicle and lightly tighten the bolt.



4. TEMPORARILY TIGHTEN REAR NO. 1 SUSPENSION ARM ASSEMBLY


    C105709
  1. Temporarily tighten the rear No. 1 suspension arm assembly LH with the bolt and nut.

    HINT:
    Insert the bolt from the front side of the vehicle and lightly tighten the bolt.



5. TEMPORARILY TIGHTEN REAR STRUT ROD ASSEMBLY


    C105708
  1. Temporarily tighten the rear strut rod assembly with the bolt and nut.

    HINT:
    Insert the bolt from the inside of the vehicle and lightly tighten the bolt.



6. STABILIZE SUSPENSION


    C166003E01
  1. Jack up the rear axle carrier sub-assembly, placing a wooden block underneath to avoid damage. Apply load to the suspension so that the rear drive shaft assembly is positioned horizontally.

    CAUTION:
    Do not jack up the rear axle carrier sub-assembly too high as the vehicle may fall.

    NOTICE:
    Do not bend the brake dust cover.

    HINT:
    1. If the rear drive shaft assembly cannot be positioned horizontally as shown in the illustration even when the rear axle carrier sub-assembly is jacked up, apply additional load to the vehicle such as by having a person sit in the rear seat.
    2. Use the same procedure for the RH side and LH side.



7. FULLY TIGHTEN REAR NO. 2 SUSPENSION ARM ASSEMBLY


    C105710
  1. Fully tighten the bolt.

    Torque:
    112 N*m{ 1141 kgf*cm , 82 ft.*lbf }

    NOTICE:
    Turn the bolt while holding the nut.



8. FULLY TIGHTEN REAR NO. 1 SUSPENSION ARM ASSEMBLY


    C105709
  1. Fully tighten the bolt.

    Torque:
    112 N*m{ 1141 kgf*cm , 82 ft.*lbf }



9. FULLY TIGHTEN REAR STRUT ROD ASSEMBLY


    C105708
  1. Fully tighten the bolt.

    Torque:
    80 N*m{ 815 kgf*cm , 59 ft.*lbf }

    NOTICE:
    Turn the bolt while holding the nut.



10. INSTALL REAR AXLE SHAFT NUT
  1. Clean the threaded parts on the drive shaft and axle hub nut using a non-residue solvent.

    NOTICE:
    1. Be sure to perform this work for a new drive shaft.
    2. Keep the threaded parts free of oil and foreign objects.



    C165541
  1. Install a new rear axle shaft nut.

    Torque:
    294 N*m{ 2996 kgf*cm , 216 ft.*lbf }

  1. Using a chisel and hammer, stake the rear axle shaft nut.



11. INSPECT AND ADJUST REAR WHEEL ALIGNMENT
(Click here)


12. INSTALL EXHAUST PIPE ASSEMBLY (for RH Side)
(Click here)


13. INSTALL REAR WHEEL

Torque:
103 N*m{ 1050 kgf*cm , 76 ft.*lbf }



14. ADD AND INSPECT HYBRID TRANSAXLE FLUID
  1. Add transaxle fluid.



    C170291E02
  1. Check that the fluid surface is within 5 mm (0.20 in.) from the lowest position of the inner surface of the transaxle filler plug opening.

    NOTICE:
    1. Stop the vehicle on a flat road.
    2. Recheck the transaxle fluid level after driving when exchanging oil.
    3. Insufficient or excessive amounts of transaxle fluid may be the cause of some trouble.

  1. Check for leaks if the transaxle fluid level is low.

  1. Using a socket hexagon wrench 10 mm, install the filler plug and a new gasket.

    Torque:
    39 N*m{ 398 kgf*cm , 29 ft.*lbf }