Home › ENGINE › 3MZ-FE ENGINE CONTROL SYSTEM › SFI SYSTEM

DTC    P0420    Catalyst System Efficiency Below Threshold (Bank 1)

DTC    P0430    Catalyst System Efficiency Below Threshold (Bank 2)

for Preparation Click here


MONITOR DESCRIPTION

The ECM (included in the hybrid vehicle control ECU) uses the two sensors, mounted in front of and behind the three-way catalytic converter, to monitor its efficiency.
The first sensor, the air fuel ratio sensor (sensor 1), sends pre-catalyst information to the ECM. The second sensor, the heated oxygen sensor (sensor 2), sends post-catalyst information to the ECM. The ECM compares the information transmitted by these two sensors to determine the efficiency of the Three-way catalytic converter performance and its ability to store oxygen.
When the Three-way catalytic converter is functioning properly, the variation in the oxygen concentration in the exhaust gas, after it has passed the three-way catalytic converter, is small. As a result, the voltage output of sensor 2 slowly alternates between the rich and lean signal voltages (shown in the illustration below). As the three-way catalytic converter performance efficiency deteriorates, its oxygen storage capacity decreases, and the variation in the oxygen concentration in the exhaust gas increases. As a result, the sensor voltage output fluctuates frequently.
While the catalyst monitor is running, the ECM measures the signal length of both sensors 1 and 2, and calculates the ratio of the signal lengths to determine the extent of the three-way catalytic converter deterioration. If the deterioration level exceeds the preset threshold, the ECM interprets this as a three-way catalytic converter malfunction. The ECM then illuminates the MIL and sets the DTC.

DTC No.
DTC Detection Condition
Trouble Area
P0420
After engine and three-way catalytic converter warmed up, and while vehicle driven within set vehicle and engine speeds, waveform of Heated Oxygen (HO2) sensor (bank 1 sensor 2) alternates frequently between rich and lean (2 trip detection logic)
  1. Gas leakage from exhaust system
  2. Exhaust pipe
  3. Air fuel ratio sensor (bank 1 sensor 1)
  4. Heated oxygen sensor (bank 1 sensor 2)
  5. Three-way catalytic converter (Exhaust manifold)
P0430
After engine and catalyst are warmed up, and while vehicle is driven within set vehicle and engine speed ranges:
Waveform of heated oxygen sensor (bank 2 sensor 2) alternates frequently between rich and lean (2 trip detection logic)
  1. Gas leakage from exhaust system
  2. Exhaust pipe
  3. Air fuel ratio sensor (bank 2 sensor 1)
  4. Heated oxygen sensor (bank 2 sensor 2)
  5. Three-way catalytic converter (Exhaust manifold)

HINT:
  1. Bank 1 refers to the bank that includes cylinder No. 1.
  2. Bank 2 refers to the bank that does not include cylinder No. 1.
  3. Sensor 1 refers to the sensor closest to the engine assembly.
  4. Sensor 2 refers to the sensor farthest away from the engine assembly.


MONITOR STRATEGY


Related DTCs
P0420: Catalyst (Bank 1) detection
P0430: Catalyst (Bank 2) detection
Required Sensors/Components (Main)
Three-way catalytic converter
Required Sensors/Components (Related)
Air fuel ratio sensor, heated oxygen sensor, intake air temperature sensor, mass air flow meter, crankshaft position sensor and engine coolant temperature sensor
Frequency of Operation
Once per driving cycle
Duration
About 30 seconds
MIL Operation
2 driving cycles
Sequence of Operation
None

TYPICAL ENABLING CONDITIONS


Monitor will run whenever this DTC is not present
P0010, P0020 (VVT Oil Control Valve Bank 1, 2)
P0011, P0021 (VVT System 1 - Advance)
P0012, P0022 (VVT System 1 - Retard)
P0016, P0018 (VVT system bank 1, 2 - misalignment)
P0031, P0032, P0051, P0052 (Air fuel ratio sensor heater - Sensor 1)
P0037, P0038, P0057, P0058 (Oxygen sensor heater - Sensor 2)
P0102, P0103 (Mass air flow meter)
P0115, P117, P0118 (Engine coolant temperature sensor)
P0120, P0121, P0122, P0123, P0220, P0222, P0223, P2135 (Throttle position sensor)
P0125 (Insufficient engine coolant temperature for closed loop)
P0136, P0137, P0138 (Oxygen sensor bank 1)
P0156, P0157, P0158 (Oxygen sensor bank 2)
P0171, P0172, P0174, P0175 (Fuel system)
P0301, P0302, P0303, P0304, P0305, P0306 (Misfire)
P0335 (Crankshaft position sensor)
P0340, P0341, P0345, P0346 (VVT sensor)
P0351, P0352, P0353, P0354, P0355, P0356 (Igniter)
P2196, P2198 (Air fuel ratio sensor - rationality)
P2237, P2240 (Air fuel ratio sensor - open)
P2238, P2241, P2252, P2255 (Air fuel ratio sensor - low impedance)
P2239, P2242, P2253, P2256 (Air fuel ratio sensor - high impedance)
P2A00, P2A03 (Air fuel ratio sensor - slow response)
Battery voltage
11 V or more
Intake air temperature
-10°C (14°F) or more
Engine coolant temperature
75°C (167°F) or more
Atmospheric pressure coefficient
0.75 or more
Idling
OFF
Engine RPM
Less than 3200 rpm
A/F sensor status
Activated
Fuel system status
Closed loop
Engine load
5% or more and less than 80%
All of the following conditions (a), (b) and (c) are met
-
(a) Mass air flow rate
10 to 64 g/sec.
(b) Estimated front catalyst temperature
530 to 660°C (986 to 1220°F)
(c) Estimated rear catalyst temperature
430 to 675°C (806 to 1247°F)
EVAP system monitor
The monitor has not run yet or the vacuum introduction has been completed
Air fuel ratio sensor monitor
Completed
Rear heated oxygen sensor heater monitor
Completed

TYPICAL MALFUNCTION THRESHOLDS


Oxygen Storage Capacity (OSC) of catalyst
Less than 0.092 g

MONITOR RESULT

Refer to CHECKING MONITOR STATUS (Click here).

CONDITIONING FOR SENSOR TESTING

HINT:
Perform the operation with the engine speeds and durations described below prior to checking the waveforms of the air fuel ratio and heated oxygen sensors. This is in order to activate the sensors sufficiently to obtain the appropriate inspection results.


A093766E35

  1. Connect the Techstream to the DLC3.
  2. Put the engine in inspection mode (Click here)
  3. Start the engine and warm it up with all the accessories switched off, until the engine coolant temperature stabilizes (Procedure "B").
  4. Run the engine at an engine speed of between 2000 rpm and 2500 rpm for at least 3 minutes (Procedure "C").
  5. While running the engine at 2500 rpm for 2 seconds and at 1500 rpm for 2 seconds, check the waveforms of the air fuel ratio and heated oxygen sensors using the Techstream (Procedure "D").

    HINT:
    1. If either of the voltage outputs of the Control the Injection Volume for A/F Sensor does not fluctuate, or either of the sensors makes noise, the sensor may be malfunctioning.
    2. If the voltage outputs of both the sensors remain lean or rich, the air fuel ratio may be extremely lean or rich. In such cases, perform the following using the Techstream.
    3. If the three-way catalyst converter has deteriorated, the heated oxygen sensor (located behind the three-way catalyst converter) voltage output fluctuates up and down frequently, even under normal driving conditions (active air fuel ratio control is not performed).


A076893E11


AIR FUEL RATIO CONTROL
Malfunctioning areas can be identified by performing the Control the Injection Volume for A/F Sensor function provided in the Active Test. The Control the Injection Volume for A/F Sensor function can help to determine whether the air fuel ratio sensor, heated oxygen sensor and other potential trouble areas are malfunctioning. The following instructions describe how to conduct the Control the Injection Volume for A/F Sensor operation using the Techstream.
  1. Connect the Techstream to the DLC3.

  2. Put the engine in inspection mode (Click here)

  3. Start the engine and turn the Techstream on.

  4. Warm up the engine at an engine speed of 2500 rpm for approximately 90 seconds.

  5. Select the following menu items: Powertrain / Engine and ECT / Active Test / Control the Injection Volume for A/F Sensor.

  6. Perform the Control the Injection Volume for A/F Sensor operation with the engine idling (press the RIGHT or LEFT button to change the fuel injection volume).

  7. Monitor the voltage outputs of the air fuel ratio and heated oxygen sensors (AFS B1S1 and O2S B1S2 or AFS B2S1 and O2S B2S2) displayed on the Techstream.

    HINT:
    1. The Control the Injection Volume for A/F Sensor operation lowers the fuel injection volume by 12.5% or increases the injection volume by 25%.
    2. Each sensor reacts in accordance with increases and decreases in the fuel injection volume.


    Standard voltage:

    Tester Display
    Injection Volumes
    Status
    Voltages
    AFS Voltage B1S1 or AFS Voltage B2S1 (Air fuel ratio)
    +25%
    Rich
    Less than 3.1 V
    AFS Voltage B1S1 or AFS Voltage B2S1 (Air fuel ratio)
    -12.5%
    Lean
    More than 3.4 V
    O2S B1S2 or O2S B2S2 (Heated oxygen)
    +25%
    Rich
    More than 0.55 V
    O2S B1S2 or O2S B2S2 (Heated oxygen)
    -12.5%
    Lean
    Less than 0.4 V

    CAUTION:
    The air fuel ratio sensor has an output delay of a few seconds and the heated oxygen sensor has a maximum output delay of approximately 20 seconds.


    Case
    Air Fuel Ratio Sensor (Sensor 1)
    Output Voltage
    Heated Oxygen Sensor (Sensor 2)
    Output Voltage
    Main Suspected Trouble Area
    1
    A162605E09
    A162598E03
    -
    2
    A162596E03
    A162598E03
    1. Air fuel ratio sensor
    2. Air fuel ratio sensor heater
    3. Air fuel ratio sensor circuit
    3
    A162605E09
    A162596E03
    1. Heated oxygen sensor
    2. Heated oxygen sensor heater
    3. Heated oxygen sensor circuit
    4
    A162596E03
    A162596E03
    1. Fuel pressure
    2. Gas leakage from exhaust system
      (Air fuel ratio extremely lean or rich)
    1. Following the Control the Injection Volume for A/F Sensor procedure enables technicians to check and graph the voltage outputs of both the air fuel ratio and heated oxygen sensors.
    2. To display the graph, select the following menu items on the Techstream: Powertrain / Engine and ECT / Active Test / Control the Injection Volume for A/F Sensor / A/F Control System / AFS B1 S1 or AFS B2 S1 and O2S B1 S2 or O2S B2 S2. Then press the graph button on the Data List view.


INSPECTION PROCEDURE

HINT:
Read freeze frame data using the Techstream. The ECM (included in the hybrid vehicle control ECU) records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can be helpful in determining whether the vehicle was running or stopped, whether the engine was warmed up or not, whether the air fuel ratio was lean or rich, as well as other data recorded at the time of a malfunction.

1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P0420 AND/OR P0430)
  1. Connect the Techstream to the DLC3.

  1. Turn the power switch on (IG) and turn the Techstream on.

  1. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

  1. Read the DTCs.

    Result:

    Display (DTC output)
    Proceed to
    P0420 and/or P0430
    A
    P0420 and/or P0430 and other DTCs
    B

    HINT:
    If any DTCs other than P0420 or P0430 are output, troubleshoot those DTCs first.



B
GO TO DTC CHART
A


2.PERFORM ACTIVE TEST USING TECHSTREAM (AIR FUEL CONTROL)
  1. Connect the Techstream to the DLC3.

  1. Put the engine in inspection mode (Click here).

  1. Start the engine and turn the Techstream on.

  1. Warm up the engine at an engine speed of 2500 rpm for approximately 90 seconds.

  1. On the Techstream, enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Injection Volume for A/F Sensor.

  1. Perform the Control the Injection Volume for A/F Sensor operation with the engine idling (press the RIGHT or LEFT button to change the fuel injection volume.).

  1. Monitor the output voltages of the air fuel ratio and heated oxygen sensors (AFS B1S1 and O2S B1S2 or AFS B2S1 and O2S B2S2) displayed on the Techstream.

    HINT:
    1. The Control the Injection Volume for A/F Sensor operation lowers the fuel injection volume by 12.5% or increases the injection volume by 25%.
    2. Each sensor reacts in accordance with increases and decreases in the fuel injection volume.


    Standard:

    Tester Display
    (Sensor)
    Injection Volume
    Status
    Voltage
    AFS Voltage B1S1 or AFS Voltage B2S1
    (Air fuel ratio)
    +25%
    Rich
    Less than 3.1 V
    AFS Voltage B1S1 or AFS Voltage B2S1
    (Air fuel ratio)
    -12.5%
    Lean
    More than 3.4 V
    O2S B1S2 or O2S B2S2
    (Heated oxygen)
    +25%
    Rich
    More than 0.55 V
    O2S B1S2 or O2S B2S2
    (Heated oxygen)
    -12.5%
    Lean
    Less than 0.4 V


    Result:

    Status
    AFS B1S1
    or
    AFS B2S1
    Status
    O2S B1S2
    or
    O2S B2S2
    Air Fuel Ratio Condition and Air Fuel Ratio and
    Heated Oxygen Sensor Conditions
    Misfire
    Main Suspected Trouble Areas
    Proceed to
    Lean/Rich
    Lean/Rich
    Normal
    -
    1. Three-Way Catalytic Converter (Three-way catalytic converter)
    2. Gas leakage from exhaust system
    A
    Lean
    Lean/Rich
    A/F sensor malfunction
    -
    Air fuel ratio sensor
    B
    Rich
    Lean/Rich
    A/F sensor malfunction
    May occur
    Air fuel ratio sensor
    B
    Lean/Rich
    Lean
    HO2 sensor malfunction
    -
    1. Heated oxygen sensor
    2. Gas leakage from exhaust system
    C
    Lean/Rich
    Rich
    HO2 sensor malfunction
    -
    1. Heated oxygen sensor
    2. Gas leakage from exhaust system
    C
    Lean
    Lean
    Actual air-fuel ratio lean
    May occur
    1. Extremely rich or lean actual air-fuel ratio
    2. Gas leakage from exhaust system
    A
    Rich
    Rich
    Actual air-fuel ratio lean
    -
    1. Extremely rich or lean actual air-fuel ratio
    2. Gas leakage from exhaust system
    A

    Lean: During Control the Injection Volume for A/F Sensor, the air fuel ratio sensor output voltage (AFS) is consistently more than 3.4 V, and the heated oxygen sensor output voltage (O2S) is consistently less than 0.4 V.
    Rich: During Control the Injection Volume for A/F Sensor, the AFS is consistently less than 3.1 V, and the O2S is consistently more than 0.55 V.
    Lean/Rich: During Control the Injection Volume for A/F Sensor of the Active Test, the output voltage of the heated oxygen sensor alternates correctly.



B
REPLACE AIR FUEL RATIO SENSOR (Click here)

C
CHECK AND REPLACE HEATED OXYGEN SENSOR, AND CHECK AND REPAIR EXHAUST GAS LEAKAGE
A


3.INSPECT FOR EXHAUST GAS LEAK

OK:
No gas leakage.



NG
REPAIR OR REPLACE EXHAUST GAS LEAKAGE POINT
OK


4.CHECK DTC OUTPUT
  1. Connect the Techstream to the DLC3.

  1. Turn the power switch on (IG) and turn the Techstream on.

  1. Enter the following menus: Powertrain / Engine and ECT / Trouble Code.

  1. Read the DTCs.

    Result:

    Display (DTC output)
    Proceed to
    P0420
    A
    P0430
    B
    P0420 and P0430
    A and B



B
Go to step 6
A


5.REPLACE EXHAUST MANIFOLD SUB-ASSEMBLY RH
  1. Replace the exhaust manifold sub-assembly RH (Click here).


NEXT

REPLACE CENTER EXHAUST PIPE ASSEMBLY (Click here)  

6.REPLACE EXHAUST MANIFOLD SUB-ASSEMBLY LH
  1. Replace the exhaust manifold sub-assembly LH (Click here).


NEXT

REPLACE CENTER EXHAUST PIPE ASSEMBLY (Click here)