Home › ENGINE › 3MZ-FE ENGINE CONTROL SYSTEM › SFI SYSTEM

DTC    P0031    Oxygen (A/F) Sensor Heater Control Circuit Low (Bank 1 Sensor 1)

DTC    P0032    Oxygen (A/F) Sensor Heater Control Circuit High (Bank 1 Sensor 1)

DTC    P0051    Oxygen (A/F) Sensor Heater Control Circuit Low (Bank 2 Sensor 1)

DTC    P0052    Oxygen (A/F) Sensor Heater Control Circuit High (Bank 2 Sensor 1)

for Preparation Click here


DESCRIPTION

HINT:
  1. Although the DTC titles say oxygen sensor, these DTCs relate to the air fuel ratio sensor.
  2. Sensor 1 refers to the sensor mounted in front of the three-way catalytic converter and located near the engine assembly.

The air fuel ratio sensor generates voltage* that corresponds to the actual air fuel ratio. This sensor voltage is used to provide the ECM (included in the hybrid vehicle control ECU) with feedback so that it can control the air-fuel ratio. The ECM determines the deviation from the stoichiometric air-fuel ratio level, and regulates the fuel injection time. If the air fuel ratio sensor malfunctions, the ECM is unable to control the air-fuel ratio accurately.
The air fuel ratio sensor is the planar type and is integrated with the heater, which heats the solid electrolyte (zirconia element). This heater is controlled by the ECM. When the intake air volume is low (the exhaust gas temperature is low), a current flows into the heater to heat the sensor, in order to facilitate accurate oxygen concentration detection. In addition, the sensor and heater portions are narrower than the conventional type. The heat generated by the heater is conducted to the solid electrolyte through the alumina, therefore the sensor activation is accelerated.
A three-way catalytic converter is used in order to convert the carbon monoxide (CO), hydrocarbon (HC), and nitrogen oxides (NOx) into less harmful substances. To allow the three-way catalytic converter to function effectively, it is necessary to keep the air-fuel ratio of the engine near the stoichiometric air-fuel ratio.
*: Value changes inside the ECM. Since the air fuel ratio sensor is the current output element, a current is converted to a voltage inside the ECM. Any measurements taken at the air fuel ratio sensor or ECM connectors will show a constant voltage.

A173183E01

HINT:
  1. When any of these DTCs are set, the ECM (included in the hybrid vehicle control ECU) enters fail-safe mode. The ECM turns off the air fuel ratio sensor heater in fail-safe mode. Fail-safe mode continues until the power switch is turned off.
  2. The ECM provides a pulse width modulated control circuit to adjust the current through the heater. The air fuel ratio sensor heater circuit uses a relay on the B+ side of the circuit.


A133850E17


DTC No.
DTC Detection Condition
Trouble Area
P0031
P0051
Air Fuel Ratio sensor heater (bank 1, 2 sensor 1) current less than 0.8 A (1 trip detection logic)
  1. Open in air fuel ratio sensor heater (bank 1, 2 sensor 1) circuit
  2. Air fuel ratio sensor heater (bank 1, 2 sensor 1)
  3. A/F relay
  4. Hybrid vehicle control ECU
P0032
P0052
Air Fuel Ratio sensor heater (bank 1, 2 sensor 1) current fail
(1-trip detection logic)
  1. Short in air fuel ratio sensor heater (bank 1, 2 sensor 1) circuit
  2. Air fuel ratio sensor heater (bank 1, 2 sensor 1)
  3. A/F relay
  4. Hybrid vehicle control ECU

HINT:
  1. Bank 1 refers to the bank that includes cylinder No. 1.
  2. Bank 2 refers to the bank that does not include cylinder No. 1.
  3. Sensor 1 refers to the sensor closest to the engine assembly.
  4. Sensor 2 refers to the sensor farthest away from the engine assembly.


MONITOR DESCRIPTION

The ECM (included in the hybrid vehicle control ECU) uses information from the air fuel ratio sensor to regulate the air fuel ratio and keep it close to the stoichiometric level. This maximizes the ability of the three-way catalytic converter to clean the exhaust gases.
The air fuel ratio sensor detects oxygen levels in the exhaust gas and transmits the information to the ECM. The inner surface of the sensor element is exposed to the outside air. The outer surface of the sensor element is exposed to the exhaust gas. The sensor element is made of platinum coated zirconia and includes an integrated heating element.
The zirconia element generates a small voltage when there is a large difference in the oxygen concentrations between the exhaust gas and outside air. The platinum coating amplifies this voltage generation.
The air fuel ratio sensor is more efficient when heated. When the exhaust gas temperature is low, the sensor cannot generate useful voltage signals without supplementary heating. The ECM regulates the supplementary heating using a duty-cycle approach to adjust the average current in the sensor heater element. If the heater current is outside the normal range, the signal transmitted by the air fuel ratio sensor will be inaccurate, as a result, the ECM will be unable to regulate air-fuel ratio properly.
When the current in the air fuel ratio sensor heater is outside the normal operating range, the ECM interprets this as a malfunction in the sensor heater and sets a DTC.
Example:
The ECM sets DTC P0032 or P0052 when the current in the A/F sensor heater fail. Conversely, when the heater current is less than 0.8 A, DTC P0031 or P0051 is set.

MONITOR STRATEGY


Related DTCs
P0031: Air fuel ratio sensor heater (bank 1) open/short (Low electrical current)
P0032: Air fuel ratio sensor heater (bank 1) open/short (High electrical current)
P0051: Air fuel ratio sensor heater (bank 2) open/short (Low electrical current)
P0052: Air fuel ratio sensor heater (bank 2) open/short (High electrical current)
Required sensors / components
Air fuel ratio sensor heater (bank 1 and 2)
Frequency of operation
Continuous
Duration
10 seconds
MIL operation
Immediate
Sequence of operation
None

TYPICAL ENABLING CONDITIONS


All: 
Monitor runs whenever following DTCs are not present
None

P0031 and P0051: 
Battery voltage
10.5 V or more
Air fuel ratio sensor heater duty-cycle ratio
50% or more
Time after engine start
10 seconds or more

P0032 and P0052: 
Air fuel ratio sensor heater duty-cycle ratio
More than 0%

TYPICAL MALFUNCTION THRESHOLDS


P0031 and P0051: 
Air fuel ratio sensor heater current
Less than 0.8 A

P0032 and P0052: 
Hybrid IC high current limiter port
Fail

COMPONENT OPERATING RANGE


P0031 and P0051: 
Air fuel ratio sensor heater current
0.8 A or more

WIRING DIAGRAM

Refer to DTC P2195 .

INSPECTION PROCEDURE

HINT:
Read freeze frame data using the Techstream. The ECM (included in the hybrid vehicle control ECU) records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can be helpful in determining whether the vehicle was running or stopped, whether the engine was warmed up or not, whether the air fuel ratio was lean or rich, as well as other data recorded at the time of a malfunction.

1.INSPECT AIR FUEL RATIO SENSOR (HEATER RESISTANCE)


    A170689E02
  1. Disconnect the air fuel ratio sensor connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Bank 1:
    Tester Connection
    Condition
    Specified Condition
    1 (HA1A) - 2 (+B)
    20°C (68°F)
    1.8 to 3.4 Ω
    1 (HA1A) - 4 (A1A-)
    Always
    10 kΩ or higher
    Bank 2:
    Tester Connection
    Condition
    Specified Condition
    1 (HA2A) - 2 (+B)
    20°C (68°F)
    1.8 to 3.4 Ω
    1 (HA2A) - 4 (A2A-)
    Always
    10 kΩ or higher

  1. Reconnect the air fuel ratio sensor connector.



NG
REPLACE AIR FUEL RATIO SENSOR (Click here)
OK


2.CHECK TERMINAL VOLTAGE (+B OF AIR FUEL RATIO SENSOR)


    A170690E02
  1. Disconnect the air fuel ratio sensor connector.

  1. Turn the power switch on (IG).

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Bank 1:
    Tester Connection
    Switch Condition
    Specified Condition
    B20-2 (+B) - Body ground
    Power switch on (IG)
    9 to 14 V
    Bank 2:
    Tester Connection
    Switch Condition
    Specified Condition
    B19-2 (+B) - Body ground
    Power switch on (IG)
    9 to 14 V

  1. Reconnect the air fuel ratio sensor connector.



NG
Go to step 5
OK


3.CHECK HARNESS AND CONNECTOR (AIR FUEL RATIO SENSOR RELAY - HYBRID VEHICLE CONTROL ECU)


    A184181E03
  1. Disconnect the air fuel ratio sensor connector.

  1. Disconnect the hybrid vehicle control ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance (Check for open):
    Bank 1:
    Tester Connection
    Condition
    Specified Condition
    B20-1 (HA1A) - B2-4 (HA1A)
    Always
    Below 1 Ω
    Bank 2:
    Tester Connection
    Condition
    Specified Condition
    B19-1 (HA2A) - B2-3 (HA2A)
    Always
    Below 1 Ω


    Standard resistance (Check for short):
    Bank 1:
    Tester Connection
    Condition
    Specified Condition
    B20-1 (HA1A) or B2-4 (HA1A) - Body ground
    Always
    10 kΩ or higher
    Bank 2:
    Tester Connection
    Condition
    Specified Condition
    B19-1 (HA2A) or B2-3 (HA2A) - Body ground
    Always
    10 kΩ or higher

  1. Reconnect the hybrid vehicle control ECU connector.

  1. Reconnect the air fuel ratio sensor connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (AIR FUEL RATIO SENSOR - HYBRID VEHICLE CONTROL ECU)
OK


4.CHECK WHETHER DTC OUTPUT RECURS
  1. Connect the Techstream to the DLC3.

  1. Turn the power switch on (IG).

  1. Turn the Techstream on.

  1. Clear the DTCs (Click here).

  1. Start the engine.

  1. Allow the engine to idle for 1 minute or more.

  1. Select the following menu items: Powertrain / Engine and ECT / Trouble Code.

  1. Read the DTCs.

    Result:

    Display (DTC Output)
    Proceed to
    No output
    A
    P0031, P0032, P0051 and/or P0052
    B



B
REPLACE HYBRID VEHICLE CONTROL ECU (Click here)
A

CHECK FOR INTERMITTENT PROBLEMS 

5.INSPECT FUSE (A/F FUSE)


    A179777E01
  1. Remove the A/F fuse from the engine room relay block.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    A/F fuse
    Always
    Below 1 Ω

  1. Reinstall the A/F fuse.



NG
REPLACE FUSE (A/F FUSE)
OK


6.INSPECT ENGINE ROOM JUNCTION BLOCK ASSEMBLY (A/F RELAY)
  1. Inspect the A/F relay (Click here).



NG
REPLACE ENGINE ROOM JUNCTION BLOCK ASSEMBLY
OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (A/F FUSE - AIR FUEL RATIO SENSOR)