Home › HYBRID SYSTEM · P310 › HYBRID VEHICLE CONTROL › HYBRID CONTROL SYSTEM

DTC    U0110-160    Lost Communication with Driver Motor Control Module

for Preparation Click here


DESCRIPTION

Refer to the description for DTC U0110-159 .

DTC No.
INF Code
DTC Detection Condition
Trouble Area
U0110
160
Error in transmission to inverter with converter assembly (MG ECU) via serial communication (no transmission, out of communication standard)
  1. Wire harness or connector
  2. Inverter with converter assembly (MG ECU)
  3. Hybrid vehicle control ECU

WIRING DIAGRAM

Refer to the wiring diagram for DTC U0110-159 .

INSPECTION PROCEDURE

CAUTION:
  1. Before inspecting the high-voltage system or disconnecting the low voltage connector of the inverter with converter assembly, take safety precautions such as wearing insulated gloves and removing the service plug grip to prevent electrical shocks. After removing the service plug grip, put it in your pocket to prevent other technicians from accidentally reconnecting it while you are working on the high-voltage system.
  2. After disconnecting the service plug grip, wait for at least 5 minutes before touching any of the high-voltage connectors or terminals. After waiting for 5 minutes, check the voltage at the terminals in the inspection point in the inverter with converter assembly. The voltage should be 0 V before beginning work.

HINT:
Waiting for at least 5 minutes is required to discharge the high-voltage capacitor inside the inverter with converter assembly.

1.CHECK HYBRID VEHICLE CONTROL ECU (CHECK WAVEFORM)


    A175156E02
  1. Connect an oscilloscope between the hybrid vehicle control ECU terminals specified in the following table, and measure the waveform.
    Item
    Contents
    Terminal
    A43-18 (HTM+) - B3-5 (E1)
    A43-17 (HTM-) - B3-5 (E1)
    Equipment Setting
    1 V/DIV, 200 μs/DIV
    Condition
    Power switch on (IG)

    Result:
    Result
    Proceed to
    The waveform appears as shown in the illustration.
    A
    The waveform differs from the one shown in the illustration.
    B

    HINT:
    The shape of the waveform may vary according to communication conditions.



B
Go to step 4
A


2.CHECK HYBRID VEHICLE CONTROL ECU (CHECK WAVEFORM)


    A175154E03
  1. Connect an oscilloscope between the hybrid vehicle control ECU terminals specified in the following table, and measure the waveform.
    Item
    Contents
    Terminal
    A43-22 (CLK+) - B3-5 (E1)
    A43-29 (CLK-) - B3-5 (E1)
    Equipment Setting
    1 V/DIV, 1 μs/DIV
    Condition
    Power switch on (IG)

    Result:
    Result
    Proceed to
    The waveform appears as shown in the illustration.
    A
    The waveform differs from the one shown in the illustration.
    B

    HINT:
    The shape of the waveform may vary according to communication conditions.



B
Go to step 6
A


3.CHECK HYBRID VEHICLE CONTROL ECU (CHECK WAVEFORM)


    A175155E04
  1. Connect an oscilloscope between the hybrid vehicle control ECU terminals specified in the following table, and measure the waveform.
    Item
    Contents
    Terminal
    A43-23 (REQ+) - B3-5 (E1)
    A43-30 (REQ-) - B3-5 (E1)
    Equipment Setting
    1 V/DIV, 1 ms/DIV
    Condition
    Power switch on (IG)

    Result:
    Result
    Proceed to
    The waveform appears as shown in the illustration.
    A
    The waveform differs from the one shown in the illustration.
    B

    HINT:
    The shape of the waveform may vary according to communication conditions.



B
Go to step 8
A

REPLACE INVERTER WITH CONVERTER ASSEMBLY (Click here)  

4.CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU - MG ECU)

CAUTION:
Be sure to wear insulated gloves.

  1. Turn the power switch off.

  1. Remove the service plug grip (Click here).

  1. Disconnect connector A43 from the hybrid vehicle control ECU.

  1. Remove the inverter cover (Click here).

    NOTICE:
    1. Wrap the round interlock terminal for the inverter cover with insulating tape to prevent it from shorting to ground.
    2. Be sure to prevent coolant in the inverter reserve tank from entering the inverter.
    3. Removing the inverter cover causes the MG ECU board to be exposed. Therefore, temporarily install the inverter cover for each area to be inspected.

  1. Disconnect connector A42 from the MG ECU.

  1. Turn the power switch on (IG).



    A175145E12
  1. Measure the voltage according to the value(s) in the table below.

    HINT:
    Turning the power switch on (IG) with the service plug grip and inverter cover removed causes an interlock switch system DTC (P0A0D-350) to be set.

    Standard voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    A43-18 (HTM+) - Body ground
    Power switch on (IG)
    Below 1 V
    A43-17 (HTM-) - Body ground
    Power switch on (IG)
    Below 1 V

  1. Turn the power switch off.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance (Check for open):
    Tester Connection
    Switch Condition
    Specified Condition
    A43-18 (HTM+) - A42-12 (HTM+)
    Power switch off
    Below 1 Ω
    A43-17 (HTM-) - A42-13 (HTM-)
    Power switch off
    Below 1 Ω

    Standard resistance (Check for short):
    Tester Connection
    Switch Condition
    Specified Condition
    A43-18 (HTM+) or A42-12 (HTM+) - Body ground and other terminals
    Power switch off
    10 kΩ or higher
    A43-17 (HTM-) or A42-13 (HTM-) - Body ground and other terminals
    Power switch off
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


5.CHECK INVERTER WITH CONVERTER ASSEMBLY
  1. Connect connector A42 to the MG ECU.



    A175539E09
  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    A43-18 (HTM+) - A43-17 (HTM-)
    Power switch off
    115 to 130 Ω



NG
REPLACE INVERTER WITH CONVERTER ASSEMBLY (Click here)
OK

REPLACE HYBRID VEHICLE CONTROL ECU (Click here)  

6.CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU - MG ECU)

CAUTION:
Be sure to wear insulated gloves.

  1. Turn the power switch off.

  1. Remove the service plug grip (Click here).

  1. Disconnect connector A43 from the hybrid vehicle control ECU.

  1. Remove the inverter cover (Click here).

    NOTICE:
    1. Wrap the round interlock terminal for the inverter cover with insulating tape to prevent it from shorting to ground.
    2. Be sure to prevent coolant in the inverter reserve tank from entering the inverter.
    3. Removing the inverter cover causes the MG ECU board to be exposed. Therefore, temporarily install the inverter cover for each area to be inspected.

  1. Disconnect connector A42 from the MG ECU.

  1. Turn the power switch on (IG).



    A175145E09
  1. Measure the voltage according to the value(s) in the table below.

    HINT:
    Turning the power switch on (IG) with the service plug grip and inverter cover removed causes an interlock switch system DTC (P0A0D-350) to be set.

    Standard voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    A43-22 (CLK+) - Body ground
    Power switch on (IG)
    Below 1 V
    A43-29 (CLK-) - Body ground
    Power switch on (IG)
    Below 1 V

  1. Turn the power switch off.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance (Check for open):
    Tester Connection
    Switch Condition
    Specified Condition
    A43-22 (CLK+) - A42-17 (CLK+)
    Power switch off
    Below 1 Ω
    A43-29 (CLK-) - A42-18 (CLK-)
    Power switch off
    Below 1 Ω

    Standard resistance (Check for short):
    Tester Connection
    Switch Condition
    Specified Condition
    A43-22 (CLK+) or A42-17 (CLK+) - Body ground and other terminals
    Power switch off
    10 kΩ or higher
    A43-29 (CLK-) or A42-18 (CLK-) - Body ground and other terminals
    Power switch off
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


7.CHECK INVERTER WITH CONVERTER ASSEMBLY
  1. Connect connector A42 to the MG ECU.



    A175539E06
  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    A43-22 (CLK+) - A43-29 (CLK-)
    Power switch off
    115 to 130 Ω



NG
REPLACE INVERTER WITH CONVERTER ASSEMBLY (Click here)
OK

REPLACE HYBRID VEHICLE CONTROL ECU (Click here)  

8.CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU - MG ECU)

CAUTION:
Be sure to wear insulated gloves.

  1. Turn the power switch off.

  1. Remove the service plug grip (Click here).

  1. Disconnect connector A43 from the hybrid vehicle control ECU.

  1. Remove the inverter cover (Click here).

    NOTICE:
    1. Wrap the round interlock terminal for the inverter cover with insulating tape to prevent it from shorting to ground.
    2. Be sure to prevent coolant in the inverter reserve tank from entering the inverter.
    3. Removing the inverter cover causes the MG ECU board to be exposed. Therefore, temporarily install the inverter cover for each area to be inspected.

  1. Disconnect connector A42 from the MG ECU.

  1. Turn the power switch on (IG).



    A175145E10
  1. Measure the voltage according to the value(s) in the table below.

    HINT:
    Turning the power switch on (IG) with the service plug grip and inverter cover removed causes an interlock switch system DTC (P0A0D-350) to be set.

    Standard voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    A43-23 (REQ+) - Body ground
    Power switch on (IG)
    Below 1 V
    A43-30 (REQ-) - Body ground
    Power switch on (IG)
    Below 1 V

  1. Turn the power switch off.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance (Check for open):
    Tester Connection
    Switch Condition
    Specified Condition
    A43-23 (REQ+) - A42-15 (REQ+)
    Power switch off
    Below 1 Ω
    A43-30 (REQ-) - A42-16 (REQ-)
    Power switch off
    Below 1 Ω

    Standard resistance (Check for short):
    Tester Connection
    Switch Condition
    Specified Condition
    A43-23 (REQ+) or A42-15 (REQ+) - Body ground and other terminals
    Power switch off
    10 kΩ or higher
    A43-30 (REQ-) or A42-16 (REQ-) - Body ground and other terminals
    Power switch off
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


9.CHECK INVERTER WITH CONVERTER ASSEMBLY
  1. Connect connector A42 to the MG ECU.



    A175539E07
  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    A43-23 (REQ+) - A43-30 (REQ-)
    Power switch off
    115 to 130 Ω



NG
REPLACE INVERTER WITH CONVERTER ASSEMBLY (Click here)
OK

REPLACE HYBRID VEHICLE CONTROL ECU (Click here)