Home › HYBRID SYSTEM · P310 › HYBRID VEHICLE CONTROL › HYBRID CONTROL SYSTEM

DTC    P3233-750    Short to B+ in Blocking of HV Gate Connection

for Preparation Click here


DESCRIPTION

Refer to the description for DTC P3232-749 .

DTC No.
INF Code
DTC Detection Condition
Trouble Area
P3233
750
Open or +B short in emergency shutdown signal circuit
  1. Wire harness or connector
  2. Hybrid vehicle control ECU
  3. Inverter with converter assembly (MG ECU)

WIRING DIAGRAM

Refer to the wiring diagrams for DTC P3232-749 and DTC P0A08-264 .

INSPECTION PROCEDURE

CAUTION:
  1. Before inspecting the high-voltage system or disconnecting the low voltage connector of the inverter with converter assembly, take safety precautions such as wearing insulated gloves and removing the service plug grip to prevent electrical shocks. After removing the service plug grip, put it in your pocket to prevent other technicians from accidentally reconnecting it while you are working on the high-voltage system.
  2. After disconnecting the service plug grip, wait for at least 5 minutes before touching any of the high-voltage connectors or terminals. After waiting for 5 minutes, check the voltage at the terminals in the inspection point in the inverter with converter assembly. The voltage should be 0 V before beginning work.

HINT:
  1. Waiting for at least 5 minutes is required to discharge the high-voltage capacitor inside the inverter with converter assembly.
  2. If DTC P0A78-305, P0A7A-343, or P0A79-697 is output together with P3233-750, the HSDN circuit may be shorted to +B.

1.CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU - MG ECU)

CAUTION:
Be sure to wear insulated gloves.

  1. Turn the power switch off.

  1. Remove the service plug grip (Click here).

  1. Disconnect connector A43 from the hybrid vehicle control ECU.

    NOTICE:
    After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.

  1. Remove the inverter cover (Click here).

    NOTICE:
    1. Wrap the round interlock terminal for the inverter cover with insulating tape to prevent it from shorting to ground.
    2. Be sure to prevent coolant in the inverter reserve tank from entering the inverter.
    3. Removing the inverter cover causes the MG ECU board to be exposed. Therefore, temporarily install the inverter cover for each area to be inspected.

  1. Disconnect connector A42 from the inverter with converter assembly (MG ECU).

  1. Turn the power switch on (IG).



    A175145E08
  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    A43-21 (HSDN) - Body ground
    Power switch on (IG)
    Below 1 V

  1. Turn the power switch off.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    A43-21 (HSDN) - A42-26 (HSDN)
    Power switch off
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


2.CHECK INVERTER WITH CONVERTER ASSEMBLY

CAUTION:
Be sure to wear insulated gloves.



    A175152E06
  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    A42-26 (HSDN) - A42-7 (+B)
    Power switch off
    10 kΩ or higher
    A42-26 (HSDN) - A42-4 (+B2)
    Power switch off
    10 kΩ or higher
    A42-26 (HSDN) - Body ground
    Power switch off
    2.65 to 3.55 kΩ



NG
REPLACE INVERTER WITH CONVERTER ASSEMBLY (Click here)
OK

REPLACE HYBRID VEHICLE CONTROL ECU (Click here)