Home › ENGINE › 3MZ-FE ENGINE CONTROL SYSTEM › SFI SYSTEM

DTC    P0351    Ignition Coil "A" Primary / Secondary Circuit

DTC    P0352    Ignition Coil "B" Primary / Secondary Circuit

DTC    P0353    Ignition Coil "C" Primary / Secondary Circuit

DTC    P0354    Ignition Coil "D" Primary / Secondary Circuit

DTC    P0355    Ignition Coil "E" Primary / Secondary Circuit

DTC    P0356    Ignition Coil "F" Primary / Secondary Circuit

for Preparation Click here


DESCRIPTION

HINT:
  1. These DTCs indicate malfunctions relating to the primary circuit.
  2. If DTC P0351 is set, check the No. 1 ignition coil circuit.
  3. If DTC P0352 is set, check the No. 2 ignition coil circuit.
  4. If DTC P0353 is set, check the No. 3 ignition coil circuit.
  5. If DTC P0354 is set, check the No. 4 ignition coil circuit.
  6. If DTC P0355 is set, check the No. 5 ignition coil circuit.
  7. If DTC P0356 is set, check the No. 6 ignition coil circuit.

A Direct Ignition System (DIS) is used on this vehicle.
The DIS is an ignition system in which each cylinder is ignited by one ignition coil and the spark plug which is connected to the end of each secondary wiring. A powerful voltage, generated in the secondary wiring of the coil, is applied directly to each spark plug. The spark of the spark plugs pass from the center electrode to the ground electrode.
The ECM (included in the hybrid vehicle control ECU) determines the ignition timing and transmits the ignition signals (IGT) to each cylinder. Using the IGT signal, the ECM turns the power transistor inside the igniter on and off. The power transistor, in turn, switches on and off the current to the primary coil. When the current to the primary coil is cut off, a powerful voltage is generated in the secondary coil. This voltage is applied to the spark plugs, causing them to spark inside the cylinders. As the ECM cuts the current to the primary coil, the igniter sends back an ignition confirmation signal (IGF) to the ECM, for each cylinder ignition.

A082677E12


DTC No.
DTC Detection Condition
Trouble Area
P0351
P0352
P0353
P0354
P0355
P0356
No IGF signal to ECM (included in the hybrid vehicle control ECU) while engine running
(1 trip detection logic)
  1. Ignition system
  2. Open or short in IGF and IGT circuit (1 to 6) between ignition coil and hybrid vehicle control ECU
  3. No. 1 to No. 6 ignition coils
  4. Hybrid vehicle control ECU
Reference: Inspection using an oscilloscope.
A031764E01
While cranking or idling the engine, check the waveform between terminals IGT (1 to 6) and E1, and IGF and E1 of the hybrid vehicle control ECU connector.

Item
Content
Terminals
CH1: IGT1, IGT2, IGT3, IGT4, IGT5, IGT6 - E1
CH2: IGF - E1
Equipment Settings
2 V/Division, 20 ms/DIvision
Conditions
Cranking or idling

MONITOR DESCRIPTION


A082388E28

If the ECM (Included in the hybrid vehicle control ECU) does not receive any IGF signals despite transmitting the IGT signal, it interprets this as a fault in the igniter and sets a DTC.
If the malfunction is not repaired successfully, a DTC is set 1 second after the engine is next started.

MONITOR STRATEGY


Related DTCs
P0351: Igniter (cylinder 1) malfunction
P0352: Igniter (cylinder 2) malfunction
P0353: Igniter (cylinder 3) malfunction
P0354: Igniter (cylinder 4) malfunction
P0355: Igniter (cylinder 5) malfunction
P0356: Igniter (cylinder 6) malfunction
Required Sensors/Components (Main)
Igniter (Cylinder 1 to 6)
Frequency of Operation
Continuous
Duration
0.256 seconds and 4 sparks
MIL Operation
Immediate
Sequence of Operation
None

TYPICAL ENABLING CONDITIONS


Monitor runs whenever following DTCs are not present
None
Either of following conditions 1 or 2 is met
-
1. Following conditions (a) and (b) are met:
-
(a) Engine RPM
500 rpm or less
(b) Battery voltage
6 V or more
2. Following conditions (a) and (b) are met:
-
(a) Engine RPM
More than 500 rpm
(b) Battery voltage
10 V or more

TYPICAL MALFUNCTION THRESHOLDS


Ignition signal fail count
More than 2 times

COMPONENT OPERATING RANGE


IGF signal
Igniter transmits IGF signal when it receives IGT signal from ECM (included in the hybrid vehicle control ECU)

WIRING DIAGRAM


A179771E02


A172772E03


INSPECTION PROCEDURE

HINT:
Read freeze frame data using the Techstream. The ECM (included in the hybrid vehicle control ECU) records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can be helpful in determining whether the vehicle was running or stopped, whether the engine was warmed up or not, whether the air fuel ratio was lean or rich, as well as other data recorded at the time of a malfunction.

1.PERFORM SIMULATION TEST
  1. Clear the DTC(s) (Click here).

  1. Change the arrangement of the ignition coils (with igniters).

    NOTICE:
    Do not change the location of the connectors.

  1. Perform a simulation test.

    Result:

    Display (DTC Output)
    Proceed to
    Same DTCs (that have been erased)
    A
    Other DTCs
    B



B
REPLACE IGNITION COIL ASSEMBLY (Click here)
A


2.INSPECT IGNITION COIL ASSEMBLY (POWER SOURCE)


    A178690E02
  1. Disconnect the ignition coil assembly connectors.

  1. Turn the power switch on (IG).

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Condition
    Specified Condition
    B30-1 - Body ground
    Always
    11 to 14 V
    B31-1 - Body ground
    Power switch on (IG)
    11 to 14 V
    B32-1 - Body ground
    Power switch on (IG)
    11 to 14 V
    B33-1 - Body ground
    Power switch on (IG)
    11 to 14 V
    B34-1 - Body ground
    Power switch on (IG)
    11 to 14 V
    B35-1 - Body ground
    Power switch on (IG)
    11 to 14 V

  1. Reconnect the ignition coil assembly connectors.



NG
Go to step 5
OK


3.CHECK HARNESS AND CONNECTOR (IGNITION COIL ASSEMBLY - HYBRID VEHICLE CONTROL ECU)


    A110908E08
  1. Disconnect the ignition coil assembly connectors.

  1. Disconnect the hybrid vehicle control ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance (Check for open):
    Tester Connection
    Condition
    Specified Condition
    B30-3 (IGT1) - B1-8 (IGT1)
    Always
    Below 1 Ω
    B31-3 (IGT2) - B1-9 (IGT2)
    Always
    Below 1 Ω
    B32-3 (IGT3) - B1-10 (IGT3)
    Always
    Below 1 Ω
    B33-3 (IGT4) - B1-11 (IGT4)
    Always
    Below 1 Ω
    B34-3 (IGT5) - B1-12 (IGT5)
    Always
    Below 1 Ω
    B35-3 (IGT6) - B1-13 (IGT6)
    Always
    Below 1 Ω

    Standard resistance (Check for short):
    Tester Connection
    Condition
    Specified Condition
    B30-3 (IGT1) or B1-8 (IGT1) - Body ground
    Always
    10 kΩ or higher
    B31-3 (IGT2) or B1-9 (IGT2) - Body ground
    Always
    10 kΩ or higher
    B32-3 (IGT3) or B1-10 (IGT3) - Body ground
    Always
    10 kΩ or higher
    B33-3 (IGT4) or B1-11 (IGT4) - Body ground
    Always
    10 kΩ or higher
    B34-3 (IGT5) or B1-12 (IGT5) - Body ground
    Always
    10 kΩ or higher
    B35-3 (IGT6) or B1-13 (IGT6) - Body ground
    Always
    10 kΩ or higher

  1. Reconnect the ignition coil assembly connectors.

  1. Reconnect the hybrid vehicle control ECU connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (IGNITION COIL ASSEMBLY - HYBRID VEHICLE CONTROL ECU)
OK


4.CHECK HARNESS AND CONNECTOR (IGNITION COIL ASSEMBLY - HYBRID VEHICLE CONTROL ECU)


    A110908E09
  1. Disconnect the ignition coil assembly connectors.

  1. Disconnect the hybrid vehicle control ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance (Check for open):
    Tester Connection
    Condition
    Specified Condition
    B30-2 (IGF) - B1-24 (IGF)
    Always
    Below 1 Ω
    B31-2 (IGF) - B1-24 (IGF)
    Always
    Below 1 Ω
    B32-2 (IGF) - B1-24 (IGF)
    Always
    Below 1 Ω
    B33-2 (IGF) - B1-24 (IGF)
    Always
    Below 1 Ω
    B34-2 (IGF) - B1-24 (IGF)
    Always
    Below 1 Ω
    B35-2 (IGF) - B1-24 (IGF)
    Always
    Below 1 Ω

    Standard resistance (Check for short):
    Tester Connection
    Condition
    Specified Condition
    B30-2 (IGF) or B1-24 (IGF) - Body ground
    Always
    10 kΩ or higher
    B31-2 (IGF) or B1-24 (IGF) - Body ground
    Always
    10 kΩ or higher
    B32-2 (IGF) or B1-24 (IGF) - Body ground
    Always
    10 kΩ or higher
    B33-2 (IGF) or B1-24 (IGF) - Body ground
    Always
    10 kΩ or higher
    B34-2 (IGF) or B1-24 (IGF) - Body ground
    Always
    10 kΩ or higher
    B35-2 (IGF) or B1-24 (IGF)- Body ground
    Always
    10 kΩ or higher

  1. Reconnect the ignition coil assembly connectors.

  1. Reconnect the hybrid vehicle control ECU connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (IGNITION COIL ASSEMBLY - HYBRID VEHICLE CONTROL ECU)
OK

REPLACE HYBRID VEHICLE CONTROL ECU (Click here)  

5.CHECK HARNESS AND CONNECTOR (IGNITION COIL ASSEMBLY - BODY GROUND)


    A157860E25
  1. Disconnect the ignition coil assembly connectors.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance (Check for open):
    Tester Connection
    Condition
    Specified Condition
    B30-4 (GND) - Body ground
    Always
    Below 1 Ω
    B31-4 (GND)) - Body ground
    Always
    Below 1 Ω
    B32-4 (GND) - Body ground
    Always
    Below 1 Ω
    B33-4 (GND) - Body ground
    Always
    Below 1 Ω
    B34-4 (GND) - Body ground
    Always
    Below 1 Ω
    B35-4 (GND) - Body ground
    Always
    Below 1 Ω

  1. Reconnect the ignition coil assembly connectors.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (IGNITION COIL ASSEMBLY - BODY GROUND)
OK


6.INSPECT FUSE (INJ NO. 1 FUSE)


    A179777E08
  1. Remove the INJ No. 1 fuse from the engine room relay block.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    INJ No. 1 fuse
    Always
    Below 1 Ω

  1. Reinstall the INJ No. 1 fuse.



NG
REPLACE FUSE (INJ NO. 1 FUSE)
OK


7.CHECK HARNESS AND CONNECTOR


    A179781E01
  1. Disconnect the ignition coil assembly connectors.

  1. Remove the IG2 relay from the engine room relay block.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance (Check for open):
    Tester Connection
    Condition
    Specified Condition
    B30-1 (+B) - IG2 relay terminal 3
    Always
    Below 1 Ω
    B31-1 (+B) - IG2 relay terminal 3
    Always
    Below 1 Ω
    B32-1 (+B) - IG2 relay terminal 3
    Always
    Below 1 Ω
    B33-1 (+B) - IG2 relay terminal 3
    Always
    Below 1 Ω
    B34-1 (+B) - IG2 relay terminal 3
    Always
    Below 1 Ω
    B35-1 (+B) - IG2 relay terminal 3
    Always
    Below 1 Ω

    Standard resistance (Check for short):
    Tester Connection
    Condition
    Specified Condition
    B30-1 (+B) or IG2 relay terminal 3 - Body ground
    Always
    10 kΩ or higher
    B31-1 (+B) or IG2 relay terminal 3 - Body ground
    Always
    10 kΩ or higher
    B32-1 (+B) or IG2 relay terminal 3 - Body ground
    Always
    10 kΩ or higher
    B33-1 (+B) or IG2 relay terminal 3 - Body ground
    Always
    10 kΩ or higher
    B34-1 (+B) or IG2 relay terminal 3 - Body ground
    Always
    10 kΩ or higher
    B35-1 (+B) or IG2 relay terminal 3 - Body ground
    Always
    10 kΩ or higher

  1. Reinstall the IG2 relay.

  1. Reconnect the ignition coil assembly connectors.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (IG2 RELAY - IGNITION COIL ASSEMBLY)
OK

CHECK ECM POWER SOURCE CIRCUIT (Click here)