Home › ENGINE › 3MZ-FE ENGINE CONTROL SYSTEM › SFI SYSTEM

DTC    P2237    Oxygen (A/F) Sensor Pumping Current Circuit / Open (Bank 1 Sensor 1)

DTC    P2238    Oxygen (A/F) Sensor Pumping Current Circuit Low (Bank 1 Sensor 1)

DTC    P2239    Oxygen (A/F) Sensor Pumping Current Circuit High (Bank 1 Sensor 1)

DTC    P2240    Oxygen (A/F) Sensor Pumping Current Circuit / Open (Bank 2 Sensor 1)

DTC    P2241    Oxygen (A/F) Sensor Pumping Current Circuit Low (Bank 2 Sensor 1)

DTC    P2242    Oxygen (A/F) Sensor Pumping Current Circuit High (Bank 2 Sensor 1)

DTC    P2252    Oxygen (A/F) Sensor Reference Ground Circuit Low (Bank 1 Sensor 1)

DTC    P2253    Oxygen (A/F) Sensor Reference Ground Circuit High (Bank 1 Sensor 1)

DTC    P2255    Oxygen (A/F) Sensor Reference Ground Circuit Low (Bank 2 Sensor 1)

DTC    P2256    Oxygen (A/F) Sensor Reference Ground Circuit High (Bank 2 Sensor 1)

for Preparation Click here


DESCRIPTION

HINT:
  1. Although the DTC titles say oxygen sensor, these DTCs relate to the air fuel ratio sensor.
  2. Sensor 1 refers to the sensor mounted in front of the three-way catalytic converter and located near the engine assembly.

The air fuel ratio sensor generates voltage* that corresponds to the actual air-fuel ratio. This sensor voltage is used to provide the ECM (included in the hybrid vehicle control ECU) with feedback so that it can control the air-fuel ratio. The ECM determines the deviation from the stoichiometric air-fuel ratio level, and regulates the fuel injection time. If the air fuel ratio sensor malfunctions, the ECM is unable to control the air-fuel ratio accurately.
The air fuel ratio sensor is the planar type and is integrated with the heater, which heats the solid electrolyte (zirconia element). This heater is controlled by the ECM. When the intake air volume is low (the exhaust gas temperature is low), a current flows into the heater to heat the sensor, in order to facilitate accurate oxygen concentration detection. In addition, the sensor and heater portions are narrower than the conventional type. The heat generated by the heater is conducted to the solid electrolyte through the alumina, therefore the sensor activation is accelerated.
A three-way catalytic converter is used in order to convert the carbon monoxide (CO), hydrocarbon (HC), and nitrogen oxides (NOx) into less harmful substances. To allow the TWC to function effectively, it is necessary to keep the air-fuel ratio of the engine near the stoichiometric air-fuel ratio.
*: Value changes inside the ECM. Since the sensor is the current output element, a current is converted to a voltage inside the ECM. Any measurements taken at the sensor or ECM connectors will show a constant voltage.

A173183E01


DTC No.
DTC Detection Condition
Trouble Area
P2237
P2240
Open in the circuit between terminals A1A+ or A2A+ and A1A- or A2A- of the air fuel ratio sensor while engine is running
(2 trip detection logic)
  1. Open or short in air fuel ratio sensor (bank 1, 2 sensor 1) circuit
  2. Air fuel ratio sensor (bank 1, 2 sensor 1)
  3. Air fuel ratio sensor heater
  4. A/F relay
  5. Air fuel ratio sensor heater and relay circuits
  6. Hybrid vehicle control ECU
P2238
P2241
  1. Air fuel ratio sensor admittance: Less than 0.022 1/Ω
  2. A1A+ or A2A+ voltage 0.5 V or less for 5.0 seconds or more
  3. A1A+ or A2A+ - A1A- or A2A- voltage 0.1 V or less for 5.0 seconds or more
    (2 trip detection logic)
  1. Open or short in air fuel ratio sensor (bank 1, 2 sensor 1) circuit
  2. Air fuel ratio sensor (bank 1, 2 sensor 1)
  3. Air fuel ratio sensor heater
  4. A/F relay
  5. Air fuel ratio sensor heater and relay circuits
  6. Hybrid vehicle control ECU
P2239
P2242
A1A+ or A2A+ voltage is more than 4.5 V for 5.0 seconds or more
(2 trip detection logic)
  1. Open or short in air fuel ratio sensor (bank 1, 2 sensor 1) circuit
  2. Air fuel ratio sensor (bank 1, 2 sensor 1)
  3. Air fuel ratio sensor heater
  4. A/F relay
  5. Air fuel ratio sensor heater and relay circuits
  6. Hybrid vehicle control ECU
P2252
P2255
A1A- or A2A- voltage is 0.5 V or less for 5.0 seconds or more
(2 trip detection logic)
  1. Open or short in air fuel ratio sensor (bank 1, 2 sensor 1) circuit
  2. Air fuel ratio sensor (bank 1, 2 sensor 1)
  3. Air fuel ratio sensor heater
  4. A/F relay
  5. Air fuel ratio sensor heater and relay circuits
  6. Hybrid vehicle control ECU
P2253
P2256
A1A- or A2A- voltage is more than 4.5 V for 5.0 seconds or more
(2 trip detection logic)
  1. Open or short in air fuel ratio sensor (bank 1, 2 sensor 1) circuit
  2. Air fuel ratio sensor (bank 1, 2 sensor 1)
  3. Air fuel ratio sensor heater
  4. A/F relay
  5. Air fuel ratio sensor heater and relay circuits
  6. Hybrid vehicle control ECU

HINT:
  1. DTCs P2237, P2238, P2239, P2252 and PP2253 indicate malfunctions related to the bank 1 air fuel ratio sensor circuit.
  2. DTCs P2240, P2241, P2242, P2255 and PP2256 indicate malfunctions related to the bank 2 air fuel ratio sensor circuit.
  3. Bank 1 refers to the bank that includes cylinder No. 1.
  4. Bank 2 refers to the bank that includes cylinder No. 2.


MONITOR DESCRIPTION

The air fuel ratio sensor varies its output voltage in proportion to the air-fuel ratio. If the air fuel ratio sensor impedance (alternating current resistance) or output voltage deviates greatly from the standard range, the ECM (included in the hybrid vehicle control ECU) determines that there is an open or short in the air fuel ratio sensor circuit.

MONITOR STRATEGY


Related DTCs
P2237: Air fuel ratio sensor (Bank 1) open circuit between AF+ and AF-
P2238: Air fuel ratio sensor (Bank 1) admittance low
P2238: Air fuel ratio sensor (Bank 1) short circuit between AF+ and AF-
P2238: Air fuel ratio sensor (Bank 1) short circuit between AF+ and GND
P2239: Air fuel ratio sensor (Bank 1) short circuit between AF+ and +B
P2240: Air fuel ratio sensor (Bank 2) open circuit between AF+ and AF-
P2241: Air fuel ratio sensor (Bank 2) admittance low
P2241: Air fuel ratio sensor (Bank 2) short circuit between AF+ and AF-
P2241: Air fuel ratio sensor (Bank 2) short circuit between AF+ and GND
P2242: Air fuel ratio sensor (Bank 2) short circuit between AF+ and +B
P2252: Air fuel ratio sensor (Bank 1) short circuit between AF- and GND
P2253: Air fuel ratio sensor (Bank 1) short circuit between AF- and +B
P2255: Air fuel ratio sensor (Bank 2) short circuit between AF- and GND
P2256: Air fuel ratio sensor (Bank 2) short circuit between AF- and +B
Required Sensors/Components (Main)
Air fuel ratio sensor
Required Sensors/Components (Related)
Engine coolant temperature sensor, Crankshaft position sensor
Frequency of Operation
Continuous
Duration
10 seconds or more
MIL Operation
2 driving cycles
Sequence of Operation
None

TYPICAL ENABLING CONDITIONS


Monitor runs whenever following DTCs are not present
P0016, P0018 (VVT system bank 1, 2 - misalignment)
P0031, P0032, P0051, P0052 (Air fuel ratio sensor heater - Sensor 1)
P0102, P0103 (Mass air flow meter)
P0112, P0113 (Intake air temperature sensor)
P0115, P0117, P0118 (Engine coolant temperature sensor)
P0120, P0121, P0122, P0123, P0220, P0222, P0223, P2135 (Throttle position sensor)
P0125 (Insufficient engine coolant temperature for closed loop)
P0128 (Thermostat)
P0171, P0172, P0174, P0175 (Fuel system)
P0301, P0302, P0303, P0304, P0305, P0306 (Misfire)
P0335 (Crankshaft position sensor)
P0451, P0452, P0453, P1451, P1452, P1453 (EVAP system)
P0505 (Idle speed control)

P2237 and P2240 (Open circuit between AF+ and AF-): 
Engine
Running
Battery voltage
11 V or more

P2238 and P2241 (Admittance low): 
Engine coolant temperature
5°C (41°F) or more
Fuel cut
Not executed

Except P2237, P2240 (Open circuit between AF+ and AF-) and P2238, P2241 (Admittance low): 
Battery voltage
11 V or more
Power switch
ON
Time after power switch off to on
5 seconds or more

TYPICAL MALFUNCTION THRESHOLDS


P2237 and P2240 (Open circuit between AF+ and AF-): 
A/F sensor admittance
Less than 0.002 1/Ω

P2238 and P2241 (Admittance low): 
A/F sensor admittance
Less than 0.021 1/Ω

P2238 and P2241 (Short circuit between AF+ and GND): 
AF+ terminal voltage
0.5 V or less

P2238 and P2241 (Short circuit between AF+ and AF-): 
Difference between AF+ and AF- terminal voltages
0.1 V or less

P2239 and P2242 (Short circuit between AF+ and +B): 
AF+ terminal voltage
More than 4.5 V

P2252 and P2255 (Short circuit between AF- and GND): 
AF- terminal voltage
0.5 V or less

P2253 and P2256 (Short circuit between AF- and +B): 
AF- terminal voltage
More than 4.5 V

WIRING DIAGRAM


A179774E01


INSPECTION PROCEDURE

HINT:
Malfunctioning areas can be identified by performing the Control the Injection Volume for A/F Sensor function provided in the Active Test. The Control the Injection Volume for A/F Sensor function can help to determine whether the air fuel ratio sensor, heated oxygen sensor and other potential trouble areas are malfunctioning.

The following instructions describe how to conduct the Control the Injection Volume for A/F Sensor operation using the Techstream.
  1. Connect the Techstream to the DLC3.
  2. Put the engine in inspection mode (Click here).
  3. Start the engine and turn the Techstream on.
  4. Warm up the engine at an engine speed of 2500 rpm for approximately 90 seconds.
  5. On the Techstream, enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Injection Volume for A/F sensor.
  6. Perform the Control the Injection Volume for A/F sensor operation with the engine idling (press the RIGHT or LEFT button to change the fuel injection volume).
  7. Monitor the output voltages of the air fuel ratio and heated oxygen sensors (AFS B1S1 and O2S B1S2 or AFS B2S1 and O2S B2S2) displayed on the Techstream.

HINT:
  1. The Control the Injection Volume for A/F sensor operation lowers the fuel injection volume by 12.5% or increases the injection volume by 25%.
  2. Each sensor reacts in accordance with increases and decreases in the fuel injection volume.


Standard:

Tester Display
(Sensor)
Injection Volume
Status
Voltage
AFS Voltage B1S1 or AFS Voltage B2S1
(Air fuel ratio)
+25%
Rich
Less than 3.1 V
AFS Voltage B1S1 or AFS Voltage B2S1
(Air fuel ratio)
-12.5%
Lean
More than 3.4 V
O2S B1S2 or O2S B2S2
(Heated oxygen)
+25%
Rich
More than 0.55 V
O2S B1S2 or O2S B2S2
(Heated oxygen)
-12.5%
Lean
Less than 0.4 V

NOTICE:
The air fuel ratio sensor has an output delay of a few seconds and the heated oxygen sensor has a maximum output delay of approximately 20 seconds.


Case
Air Fuel Ratio Sensor (Sensor 1)
Output Voltage
Heated Oxygen Sensor (Sensor 2)
Output Voltage
Main Suspected Trouble Area
1
A162605E09
A162598E03
-
2
A162596E03
A162598E03
  1. Air fuel ratio sensor
  2. Air fuel ratio sensor heater
  3. Air fuel ratio sensor circuit
3
A162605E09
A162596E03
  1. Heated oxygen sensor
  2. Heated oxygen sensor heater
  3. Heated oxygen sensor circuit
4
A162596E03
A162596E03
  1. Fuel pressure
  2. Gas leakage from exhaust system
    (Air fuel ratio extremely lean or rich)
  1. Following the Control the Injection Volume for A/F sensor procedure enables technicians to check and graph the output voltages of both the air fuel ratio and heated oxygen sensors.
  2. To display the graph, enter the following menus: Powertrain / Engine and ECT / Active Test /Control the Injection Volume for A/F Sensor / AFS B1S1 and O2S B1S2 or AFS B2S1 and O2S B2S2, and press the graph button on the Data List view.

HINT:
Read freeze frame data using the Techstream. The ECM (included in the hybrid vehicle control ECU) records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can be helpful in determining whether the vehicle was running or stopped, whether the engine was warmed up or not, whether the air fuel ratio was lean or rich, as well as other data recorded at the time of a malfunction.

1.INSPECT AIR FUEL RATIO SENSOR (HEATER RESISTANCE)


    A170689E02
  1. Disconnect the air fuel ratio sensor connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Bank 1:
    Tester Connection
    Condition
    Specified Condition
    1 (HA1A) - 2 (+B)
    20°C (68°F)
    1.8 to 3.4 Ω
    1 (HA1A) - 4 (A1A-)
    Always
    10 kΩ or higher
    Bank 2:
    Tester Connection
    Condition
    Specified Condition
    1 (HA2A) - 2 (+B)
    20°C (68°F)
    1.8 to 3.4 Ω
    1 (HA2A) - 4 (A2A-)
    Always
    10 kΩ or higher

  1. Reconnect the air fuel ratio sensor connector.



NG
REPLACE AIR FUEL RATIO SENSOR (Click here)
OK


2.INSPECT ENGINE ROOM JUNCTION BLOCK ASSEMBLY
  1. Inspect the A/F relay (Click here).



NG
REPLACE ENGINE ROOM JUNCTION BLOCK ASSEMBLY
OK


3.CHECK HARNESS AND CONNECTOR (AIR FUEL RATIO SENSOR - HYBRID VEHICLE CONTROL ECU)


    A184181E04
  1. Disconnect the air fuel ratio sensor connectors.

  1. Turn the power switch off.

  1. Disconnect the hybrid vehicle control ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance (Check for open):
    Tester Connection
    Condition
    Specified Condition
    B20-1 (HA1A) - B2-4 (HA1A)
    Always
    Below 1 Ω
    B20-3 (A1A+) - B2-22 (A1A+)
    Always
    Below 1 Ω
    B20-4 (A1A-) - B2-30 (A1A-)
    Always
    Below 1 Ω
    B19-1 (HA2A) - B2-3 (HA2A)
    Always
    Below 1 Ω
    B19-3 (A2A+) - B2-23 (A2A+)
    Always
    Below 1 Ω
    B19-4 (A2A-) - B2-31 (A2A-)
    Always
    Below 1 Ω

    Standard resistance (Check for short):
    Tester Connection
    Condition
    Specified Condition
    B20-1 (HA1A) or B2-4 (HA1A) - Body ground
    Always
    10 kΩ or higher
    B20-3 (A1A+) or B2-22 (A1A+) - Body ground
    Always
    10 kΩ or higher
    B20-4 (A1A-) or B2-30 (A1A-) - Body ground
    Always
    10 kΩ or higher
    B19-1 (HA2A) or B2-3 (HA2A) - Body ground
    Always
    10 kΩ or higher
    B19-3 (A2A+) or B2-23 (A2A+) - Body ground
    Always
    10 kΩ or higher
    B19-4 (A2A-) or B2-31 (A2A-) - Body ground
    Always
    10 kΩ or higher

  1. Reconnect the hybrid vehicle control ECU connector.



  1. Reconnect the air fuel ratio sensor connector.


    A133850E17



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE HYBRID VEHICLE CONTROL ECU (Click here)