Home › HYBRID SYSTEM · P310 › HYBRID VEHICLE CONTROL › HYBRID CONTROL SYSTEM

DTC    P0A05-776    Motor Electronics Coolant Pump Control Circuit / Open

for Preparation Click here


DESCRIPTION

Refer to the description for DTC P0A02-719 .

DTC No.
INFO Code
DTC Detection Condition
Trouble Area
P0A05
776
Water pump malfunction
  1. Wire harness or connector
  2. Water pump with motor and bracket assembly
  3. Hybrid vehicle control ECU
  4. INV-W/P fuse

WIRING DIAGRAM


A174399E03


INSPECTION PROCEDURE

1.PERFORM ACTIVE TEST USING TECHSTREAM (WATER PUMP)
  1. Connect the Techstream to the DLC3.

  1. Turn the power switch on (IG).

  1. Select the following menu items: Powertrain / Hybrid Control / Trouble Codes.

  1. Clear DTCs and freeze frame data.

  1. Select the following menu items: Powertrain / Hybrid Control / Active Test / Activate the Water Pump.

  1. During the "Activate the Water Pump" active test, check operation of the water pump.

    OK:
    There are ripples in the inverter reserve tank coolant.

    HINT:
    The water pump is also activated in the power switch on (READY) state.



NG
Go to step 5
OK


2.INSPECT HYBRID VEHICLE CONTROL ECU


    A174234E02
  1. Connect the Techstream to the DLC3.

  1. Turn the power switch on (IG).

  1. Select the following menu items: Powertrain / Hybrid Control / Active Test / Activate the Water Pump.

  1. Connect an oscilloscope between the hybrid vehicle control ECU terminals specified in the table below and measure the waveform while performing the active test.
    Item
    Contents
    Terminal
    D35-29 (NIWP) - B3-5 (E1)
    Equipment Setting
    5 V/DIV., 2 ms./DIV.
    Condition
    During "Activate the Water Pump" active test

    OK:
    The waveform appears as shown in the illustration.



NG
Go to step 11
OK


3.READ OUTPUT DTC (HV)
  1. Connect the Techstream to the DLC3.

  1. Turn the power switch on (IG).

  1. Select the following menu items: Powertrain / Hybrid Control / Trouble Codes.

  1. Check if DTCs are output.

    Result:
    Result
    Proceed to
    P0A05-776 is not output
    A
    P0A05-776 is output
    B



B
REPLACE HYBRID VEHICLE CONTROL ECU (Click here)
A


4.PERFORM REPRODUCTION TEST


    A174234E03
  1. Connect the Techstream to the DLC3.

  1. Turn the power switch on (IG).

  1. Select the following menu items: Powertrain / Hybrid Control / Active Test / Activate the Water Pump.

  1. During the "Activate the Water Pump" active test, check for pulse signals according to the table below.
    Item
    Contents
    Terminal
    D35-29 (NIWP) - B3-5 (E1)
    Equipment Setting
    5 V/DIV., 2 ms./DIV.
    Condition
    During "Activate the Water Pump" active test

  1. Perform the following reproduction tests to check for intermittent problems.

    Reproduction test
    Parts to be replaced if any abnormality is found
    Wiggle the connector.
    Harness or connector
    Wiggle the harness.
    Harness or connector
    Vibrate the hybrid vehicle control ECU
    (Tap gently by hand.)
    Hybrid vehicle control ECU
    Vibrate the water pump.
    (Tap gently by hand.)
    Water pump
    Heat or cool the hybrid vehicle control ECU.
    Hybrid vehicle control ECU
    Repeatedly activate and stop the water pump.
    When the problem is reproduced, perform inspection according to the inspection flow chart.
    Raise the temperature of the coolant for inverter, and repeatedly activate and stop the water pump.
    When the problem is reproduced, perform inspection according to the inspection flow chart.

    OK:
    The interval of pulse signal output is normal.



NG
REPAIR OR REPLACE MALFUNCTIONING PARTS
OK

REPLACE WATER PUMP WITH MOTOR AND BRACKET ASSEMBLY (Click here)  

5.CHECK HARNESS AND CONNECTOR (WATER PUMP)
  1. Turn the power switch off.



    A174885
  1. Disconnect the A52 water pump with motor and bracket assembly connector.



    A174237E02
  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    A52-4 (+BWP) - A52-3 (GND)
    Power switch off
    11 to 14 V



NG
Go to step 13
OK


6.CHECK COOLANT HOSE


    A105138E04
  1. Check if the hoses of the cooling system are not kinked or clogged.

    OK:
    The hoses of the cooling system are not kinked or clogged.



NG
CORRECT THE PROBLEM
OK


7.CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU - WATER PUMP)


    A174235E03
  1. Turn the power switch off.

  1. Disconnect the D35 connector from the hybrid vehicle control ECU.

  1. Disconnect the A52 water pump with motor and bracket assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance (Check for open):
    Tester Connection
    Switch Condition
    Specified Condition
    D35-23 (IWP) - A52-2 (SWP)
    Power switch off
    Below 1 Ω

    Standard resistance (Check for short):
    Tester Connection
    Switch Condition
    Specified Condition
    D35-23 (IWP) or A52-2 (SWP) - Body ground and other terminals
    Power switch off
    100 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


8.INSPECT HYBRID VEHICLE CONTROL ECU


    A174222E15
  1. Connect the hybrid vehicle control ECU connector and water pump with motor and bracket assembly connector.

  1. Turn the power switch on (IG).

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    D35-23 (IWP) - B3-5 (E1)
    Power switch on (IG)
    Below 3.5 V



NG
Go to step 10
OK


9.INSPECT HYBRID VEHICLE CONTROL ECU


    A174222E16
  1. Turn the power switch on (READY).

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    D35-23 (IWP) - B3-5 (E1)
    Power switch on (READY)
    9 to 15.5 V



NG
REPLACE HYBRID VEHICLE CONTROL ECU (Click here)
OK

REPLACE WATER PUMP WITH MOTOR AND BRACKET ASSEMBLY (Click here)  

10.INSPECT WATER PUMP WITH MOTOR AND BRACKET ASSEMBLY (IWP TERMINAL VOLTAGE)


    A174231E05
  1. Disconnect the D35 connector from the hybrid vehicle control ECU.

  1. Turn the power switch on (IG).

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    D35-23 (IWP) - B3-5 (E1)
    Power switch on (IG)
    9 to 14 V



NG
REPLACE WATER PUMP WITH MOTOR AND BRACKET ASSEMBLY (Click here)
OK

REPLACE HYBRID VEHICLE CONTROL ECU (Click here)  

11.CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU - WATER PUMP)


    A174235E04
  1. Turn the power switch off.

  1. Disconnect the D35 connector from the hybrid vehicle control ECU.

  1. Disconnect the A52 water pump with motor and bracket assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance (Check for open):
    Tester Connection
    Switch Condition
    Specified Condition
    D35-23 (IWP) - A52-2 (SWP)
    Power switch off
    Below 1 Ω
    D35-29 (NIWP) - A52-1 (NWP)
    Power switch off
    Below 1 Ω

    Standard resistance (Check for short):
    Tester Connection
    Switch Condition
    Specified Condition
    D35-23 (IWP) or A52-2 (SWP) - Body ground and other terminals
    Power switch off
    100 kΩ or higher
    D35-29 (NIWP) or A52-1 (NWP) - Body ground and other terminals
    Power switch off
    100 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


12.INSPECT WATER PUMP WITH MOTOR AND BRACKET ASSEMBLY


    A174236E02
  1. Disconnect the A52 water pump with motor and bracket assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    A52-1 (NWP) - A52-3 (GND)
    Power switch off
    1 MΩ or higher



NG
REPLACE WATER PUMP WITH MOTOR AND BRACKET ASSEMBLY (Click here)
OK

REPLACE HYBRID VEHICLE CONTROL ECU (Click here)  

13.CHECK FUSE (INV-W/P)


    A174902E03
  1. Check if there is an open circuit in the fuse (INV-W/P) in the No. 2 engine room relay block.

    OK:
    There is no open circuit in the fuse (INV-W/P).

    HINT:
    If the result is NG, replace the fuse (INV-W/P) with a new one.



NG
REPLACE FUSE (INV-W/P)
OK

REPAIR OR REPLACE HARNESS OR CONNECTOR