Home › HYBRID SYSTEM · P310 › HYBRID VEHICLE CONTROL › HYBRID CONTROL SYSTEM

DTC    P0A2C-247    Drive Motor "A" Temperature Sensor Circuit Low

DTC    P0A2D-249    Drive Motor "A" Temperature Sensor Circuit High

for Preparation Click here


DESCRIPTION

The resistance of the thermistor built into the motor temperature sensor changes in accordance with changes in MG2 temperature. The lower the MG2 temperature, the higher the thermistor resistance. Conversely, the higher the temperature, the lower the resistance.

HINT:
The term "drive motor A" indicates MG2."


A172965E04


DTC No.
INF Code
DTC Detection Condition
Trouble Area
P0A2C
247
GND short in motor temperature sensor circuit
  1. Wire harness or connector
  2. Hybrid vehicle control ECU
  3. Hybrid vehicle transaxle assembly (Motor temperature sensor)
P0A2D
249
Open or +B short in motor temperature sensor circuit

HINT:
After confirming that DTC P0A2C-247 or P0A2D-249 is output, use Techstream to check "Motor Temp No2" in the hybrid vehicle control ECU data list.

Displayed Temperature
Malfunction
-58°F (-50°C)
Open circuit or short to +B
401°F (205°C)
Short to GND


WIRING DIAGRAM


A169640E10


INSPECTION PROCEDURE

1.CHECK CONNECTOR CONNECTION CONDITION (HYBRID VEHICLE CONTROL ECU CONNECTOR)


    A174883E01
  1. Check the connections of all hybrid vehicle control ECU connectors.

    OK:
    The connectors are connected securely and there are no contact problems.



NG
CONNECT SECURELY
OK


2.INSPECT HYBRID VEHICLE CONTROL ECU
  1. Turn the power switch on (IG).



    A174222E18
  1. Measure the voltage according to the value(s) in the table below.

    Result:

    Tester Connection
    Switch Condition
    Voltage
    Proceed to
    B1-26 (MMT) - B1-33 (MMTG)
    Power switch on (IG)
    11 to 14 V
    A
    Approximately 0 or 5 V
    B



B
Go to step 5
A


3.CHECK HARNESS AND CONNECTOR (+B SHORT)


    A174441E04
  1. Disconnect the B1 connector from the hybrid vehicle control ECU.

  1. Turn the power switch on (IG).

  1. Measure the voltage according to the value(s) in the table below.

    Result:

    Tester Connection
    Switch Condition
    Voltage
    Proceed to
    B1-26 (MMT) - B1-33 (MMTG)
    Power switch on (IG)
    11 to 14 V
    A
    Power switch on (IG)
    Approximately 0 V
    B

    NOTICE:
    Turning the power switch on (IG) with the hybrid vehicle control ECU connectors disconnected causes other DTCs to be stored. Clear the DTCs after performing this inspection.



B
REPLACE HYBRID VEHICLE CONTROL ECU (Click here)
A


4.CHECK HARNESS AND CONNECTOR (+B SHORT)
  1. Disconnect the B1 connector from the hybrid vehicle control ECU.

  1. Disconnect the B52 motor temperature sensor connector.

  1. Turn the power switch on (IG).



    A174442E03
  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    B52-1 (MMT) or B1-26 (MMT) - Body ground
    Power switch on (IG)
    Approximately 0 V

    NOTICE:
    Turning the power switch on (IG) with the hybrid vehicle control ECU connectors disconnected causes other DTCs to be stored. Clear the DTCs after performing this inspection.

    HINT:
    The motor temperature sensor is not available separately. If it requires replacement, replace the hybrid vehicle transaxle assembly.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE HYBRID VEHICLE TRANSAXLE ASSEMBLY (Click here)  

5.INSPECT MOTOR TEMPERATURE SENSOR


    A174441E03
  1. Disconnect the B1 connector from the hybrid vehicle control ECU.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    B1-26 (MMT) - B1-33 (MMTG)
    Thermistor temperature: 32°F (0°C)
    142.6 to 184.1 kΩ
    Thermistor temperature: 77°F (25°C)
    44.2 to 54.4 kΩ
    Thermistor temperature: 122°F (50°C)
    16.2 to 19.1 kΩ
    Thermistor temperature 212°F (100°C)
    3.3 to 3.5 kΩ

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    B1-26 (MMT) or B1-33 (MMTG) - Body ground and other terminals
    Power switch off
    10 kΩ or higher



NG
Go to step 6
OK

REPLACE HYBRID VEHICLE CONTROL ECU (Click here)  

6.CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU - MOTOR TEMPERATURE SENSOR)
  1. Disconnect the B1 connector from the hybrid vehicle control ECU.

  1. Disconnect the B52 motor temperature sensor connector.



    A174442E04
  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    B1-26 (MMT) - B52-1 (MMT)
    Power switch off
    Below 1 Ω
    B1-33 (MMTG) - B52-3 (MMTG)
    Power switch off
    Below 1 Ω

    Standard resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    B1-26 (MMT) or B1-33 (MMTG) - Body ground and other terminals
    Power switch off
    10 kΩ or higher

    HINT:
    The motor temperature sensor is not available separately. If it requires replacement, replace the hybrid vehicle transaxle assembly.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE HYBRID VEHICLE TRANSAXLE ASSEMBLY (Click here)