DTC P0A79-812 Drive Motor "B" Inverter Performance |
DTC P0A79-813 Drive Motor "B" Inverter Performance |
DTC P0A79-814 Drive Motor "B" Inverter Performance |
| DTC No. | INF Code | DTC Detection Condition | Trouble Area |
| P0A79 | 812 | Abnormal MGR current value detection (MG ECU malfunction) |
|
| 813 | Abnormal MGR current value detection (inverter malfunction) | ||
| 814 | Abnormal MGR current value detection (rear traction motor with transaxle assembly malfunction) |
| Related DTCs | P0A79 (INF 812/813/814): Rear motor inverter / Rear motor inverter abnormal current |
| Required sensors / components | Rear motor inverter |
| Frequency of operation | Continuous |
| Duration | TMC's intellectual property |
| MIL operation | Immediately |
| Sequence of operation | None |
| The monitor will run whenever the DTCs listed are not present | TMC's intellectual property |
| Other conditions belong to TMC's intellectual property | - |
| Rear motor inverter | Abnormal current |
| Rear motor inverter | DTC P0A79 (INF 812/813/814) is not detected |
| 1.CHECK DTC OUTPUT (HV) |
Connect the Techstream to the DLC3.
Turn the power switch on (IG).
Select the following menu items: Powertrain / Hybrid Control / Trouble Codes.
Check if DTCs are output.
| Result | Proceed to |
| P0A79-812, 813 or 814 only is output. | A |
| Any of the following DTCs are also output. | B |
| DTC No. | Relevant Diagnosis |
| P0A1C (all INF codes) *1 | Drive Motor "B" Control Module |
| P0A1D (all INF codes) *1 | Hybrid Powertrain Control Module |
| P0A45-669 | Drive Motor "B" Position Sensor Circuit |
| P0A46-671 | Drive Motor "B" Position Sensor Circuit Range / Performance |
| P0A47-670 | Drive Motor "B" Position Sensor Circuit Low |
| P0A69 (all INF codes) *1 | Drive Motor "B" Phase V Current |
| P0A6C (all INF codes) *1 | Drive Motor "B" Phase W Current |
| P0A79-672, 690, 691, 692, 693, 694, 695, 696, 697, 698, 701, 703, 704 | Drive Motor "B" Inverter Performance |
| P0A91-702, 705 | Drive Motor "B" Performance |
|
| ||||
| A | |
| 2.CHECK CONNECTOR CONNECTION CONDITION (MG ECU CONNECTOR) |
Turn the power switch off.
Remove the service plug grip (Click here).
Remove the inverter cover (Click here).
![]() |
Check the connections of the MG ECU connectors.
|
| ||||
| OK | |
| 3.CHECK INVERTER WITH CONVERTER ASSEMBLY (MGR) |
Check that the service plug grip is not installed.
![]() |
Check that the bolts for the three-phase AC cable for MGR are tightened to the specified torque, the three-phase AC cable for MGR is connected securely, and there are no contact problems.
Check for arc marks at the bolts for the rear motor cable.
| Result | Proceed to | |
| The terminals are connected securely and there are no contact problems. | There are no arc marks. | A |
| The terminals are not connected securely and there is a contact problem. | There are arc marks. | B |
| The terminals are not connected securely and there is a contact problem. | There are no arc marks. | C |
| The terminals are connected securely and there are no contact problems. | There are arc marks. | B |
|
| ||||
|
| ||||
| A | |
| 4.CHECK REAR TRACTION MOTOR WITH TRANSAXLE ASSEMBLY |
Check that the service plug grip is not installed.
![]() |
Disconnect the three-phase AC cable for MGR from the inverter.
![]() |
Using a milliohmmeter, measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| U - V | Power switch off (68°F (20°C)) | 147 to 157 mΩ |
| V - W | Power switch off (68°F (20°C)) | 147 to 157 mΩ |
| W - U | Power switch off (68°F (20°C)) | 147 to 157 mΩ |
To correct the variation of the measured resistance due to temperature, use the following formula to calculate the resistance at 68°F (20°C).
Calculate the difference between the maximum and minimum resistance.
Using a megohmmeter set to 500 V, measure the insulation resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| U - Body ground and shield ground | Power switch off | 10 MΩ or higher |
| V - Body ground and shield ground | Power switch off | 10 MΩ or higher |
| W - Body ground and shield ground | Power switch off | 10 MΩ or higher |
|
| ||||
| OK | |
| 5.CHECK HARNESS AND CONNECTOR (MG ECU - REAR MOTOR RESOLVER) |
Disconnect the A42 connector from the MG ECU.
Turn the power switch on (IG).
![]() |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| A42-21 (RRF) - Body ground | Power switch on (IG) | Below 1 V |
| A42-22 (RRFG) - Body ground | Power switch on (IG) | Below 1 V |
| A42-29 (RSN) - Body ground | Power switch on (IG) | Below 1 V |
| A42-30 (RSNG) - Body ground | Power switch on (IG) | Below 1 V |
| A42-11 (RCS) - Body ground | Power switch on (IG) | Below 1 V |
| A42-23 (RCSG) - Body ground | Power switch on (IG) | Below 1 V |
Turn the power switch off.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| A42-21 (RRF) - A42-22 (RRFG) | Power switch off | 7.65 to 10.2 Ω |
| A42-29 (RSN) - A42-30 (RSNG) | Power switch off | 12.6 to 16.8 Ω |
| A42-11 (RCS) - A42-23 (RCSG) | Power switch off | 12.6 to 16.8 Ω |
| Tester Connection | Switch Condition | Specified Condition |
| A42-21 (RRF) or A42-22 (RRFG) - Body ground and other terminals | Power switch off | 10 kΩ or higher |
| A42-29 (RSN) or A42-30 (RSNG) - Body ground and other terminals | Power switch off | 10 kΩ or higher |
| A42-11 (RCS) or A42-23 (RCSG) - Body ground and other terminals | Power switch off | 10 kΩ or higher |
|
| ||||
| OK | |
| 6.CHECK CONNECTOR CONNECTION CONDITION (REAR MOTOR RESOLVER CONNECTOR) |
![]() |
Check the connections of the rear motor resolver connector.
|
| ||||
| OK | ||
| ||
| 7.CHECK CONNECTOR CONNECTION CONDITION (REAR MOTOR RESOLVER) |
![]() |
Check the connections of the rear motor resolver connector.
|
| ||||
| OK | |
| 8.CHECK REAR MOTOR RESOLVER |
![]() |
Disconnect the j7 rear motor resolver connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| j7-1 (RRF) - j7-4 (RRFG) | Power switch off | 7.65 to 10.2 Ω |
| j7-2 (RSN) - j7-5 (RSNG) | Power switch off | 12.6 to 16.8 Ω |
| j7-3 (RCS) - j7-6 (RCSG) | Power switch off | 12.6 to 16.8 Ω |
Using a megohmmeter set to 500 V, measure the insulation resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| j7-1 (RRF) - j7-2 (RSN) | Power switch off | 10 MΩ or higher |
| j7-1 (RRF) - j7-3 (RCS) | Power switch off | 10 MΩ or higher |
| j7-2 (RSN) - j7-3 (RCS) | Power switch off | 10 MΩ or higher |
| j7-4 (RRFG) - j7-5 (RSNG) | Power switch off | 10 MΩ or higher |
| j7-4 (RRFG) - j7-6 (RCSG) | Power switch off | 10 MΩ or higher |
| j7-5 (RSNG) - j7-6 (RCSG) | Power switch off | 10 MΩ or higher |
| Each terminal listed above - Transaxle housing | Power switch off | 10 MΩ or higher |
|
| ||||
| OK | ||
| ||
| 9.CHECK NO. 3 FRAME WIRE (INVERTER WITH CONVERTER ASSEMBLY - REAR TRACTION MOTOR) |
Check that the service plug grip is not installed.
![]() |
Disconnect the No. 3 frame wire (three-phase AC cable for MGR) from the rear traction motor with transaxle assembly.
![]() |
Using a megohmmeter set to 500 V, measure the insulation resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| U - Body ground and shield ground | Power switch off | 10 MΩ or higher |
| V - Body ground and shield ground | Power switch off | 10 MΩ or higher |
| W - Body ground and shield ground | Power switch off | 10 MΩ or higher |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| U - U | Power switch off | Below 1 Ω |
| V - V | Power switch off | Below 1 Ω |
| W - W | Power switch off | Below 1 Ω |
| Tester Connection | Switch Condition | Specified Condition |
| U - V | Power switch off | 10 kΩ or higher |
| V - W | Power switch off | 10 kΩ or highe |
| W - U | Power switch off | 10 kΩ or highe |
|
| ||||
| OK | |
| 10.INSPECT EXTENSION WIRE ASSEMBLY |
Remove the rear traction motor with transaxle assembly (Click here).
Remove the extension wire assembly from the rear traction motor with transaxle assembly.
![]() |
Using a megohmmeter set to 500 V, measure the insulation resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| U - Shield shell | Power switch off | 10 MΩ or higher |
| V - Shield shell | Power switch off | 10 MΩ or higher |
| W - Shield shell | Power switch off | 10 MΩ or higher |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| U - U | Power switch off | Below 1 Ω |
| V - V | Power switch off | Below 1 Ω |
| W - W | Power switch off | Below 1 Ω |
|
| ||||
| OK | ||
| ||