Home › RESTRAINTS › SUPPLEMENTAL RESTRAINT SYSTEM › AIRBAG SYSTEM

AIRBAG SYSTEM > SRS Warning Light Remains ON

for Preparation Click here


DESCRIPTION

The SRS warning light is located on the combination meter assembly.
When the SRS is normal, the SRS warning light comes on for approximately 6 seconds after the power switch is turned from off to on (IG), and then goes off automatically (primary check period).
If there is a malfunction in the SRS, the SRS warning light comes on to inform the driver of a problem.
When terminals TC and CG of the DLC3 are connected, the DTC is displayed by the SRS warning light blinking pattern.
The SRS is equipped with a voltage-increase circuit (DC-DC converter) in the center airbag sensor assembly in case the source voltage drops.
When the battery source voltage drops, the voltage-increase circuit (DC-DC converter) functions to increase the voltage of the SRS to normal voltage.
A malfunction in this circuit is not recorded in the center airbag sensor assembly. The SRS warning light automatically goes off when the source voltage returns to normal.
The signal to illuminate the SRS warning light is transmitted from the center airbag sensor assembly to the combination meter assembly through the CAN communication system.

WIRING DIAGRAM


C170104E04


INSPECTION PROCEDURE

1.CHECK SRS WARNING LIGHT OPERATION
  1. Check the SRS warning light operation approximately 6 seconds after the power switch is turned on (IG).

    Result:
    SRS Warning Light Illumination
    Proceed to
    Remains on
    A
    Remains on after it goes off
    B



B
Go to step 6
A


2.CHECK BATTERY VOLTAGE
  1. Measure the voltage of the battery.

    Standard voltage:
    11 to 14 V



NG
INSPECT CHARGING SYSTEM AND BATTERY
OK


3.CHECK CONNECTOR
  1. Turn the power switch off.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Check that the connector is properly connected to the center airbag sensor assembly.

    OK:
    The connector is properly connected.

    HINT:
    If the connector is not connected securely, reconnect the connector and proceed to the next inspection.

  1. Disconnect the connector from the center airbag sensor assembly.

  1. Check that the terminal of the connector is not damaged.

    OK:
    The terminal is not deformed or damaged.



NG
REPLACE WIRE HARNESS
OK


4.CHECK WIRE HARNESS (CENTER AIRBAG SENSOR ASSEMBLY - BODY GROUND)


    C157605E04
  1. Connect the negative (-) terminal cable to the battery.

  1. Turn the power switch on (IG).

  1. Operate all components of the electrical system (defogger, wipers, headlights, heater blower, etc.).

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    D30-21 (IG2) - Body ground
    power switch on (IG)
    8 to 16 V

  1. Turn the power switch off.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    D30-25 (E1) - Body ground
    Always
    Below 1 Ω
    D30-26 (E2) - Body ground
    Always
    Below 1 Ω



NG
REPLACE WIRE HARNESS
OK


5.CHECK SRS WARNING LIGHT
  1. Turn the power switch on (IG).

  1. Check the SRS warning light condition.

    OK:
    After the primary check period, the SRS warning light goes off for approximately 10 seconds and then remains on.

    HINT:
    The primary check period is for approximately 6 seconds after the power switch is turned on (IG).



NG
REPLACE COMBINATION METER ASSEMBLY (Click here)
OK

REPLACE CENTER AIRBAG SENSOR ASSEMBLY (Click here)  

6.CHECK CAN COMMUNICATION SYSTEM
  1. Use Techstream to check if the CAN communication system is functioning normally.

    HINT:
    1. Refer to "Bus Check" of the CAN communication system (Click here).
    2. The center airbag sensor assembly is connected to the CAN communication system. Therefore, before starting troubleshooting, make sure to check that there is no trouble in the CAN communication system.

    Result:
    Result
    Proceed to
    DTC is not output
    A
    DTC is output
    B



B
GO TO CAN COMMUNICATION SYSTEM (Click here)
A


7.CHECK BATTERY VOLTAGE
  1. Measure the voltage of the battery.

    Standard voltage:
    11 to 14 V



NG
INSPECT CHARGING SYSTEM AND BATTERY
OK


8.CHECK CONNECTOR
  1. Turn the power switch off.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Check that the connector is properly connected to the center airbag sensor assembly.

    OK:
    The connector is properly connected.

    HINT:
    If the connector is not connected securely, reconnect the connector and proceed to the next inspection.

  1. Disconnect the connector from the center airbag sensor assembly.

  1. Check that the terminal of the connector is not damaged.

    OK:
    The terminal is not deformed or damaged.



NG
REPLACE WIRE HARNESS
OK


9.CHECK WIRE HARNESS (CENTER AIRBAG SENSOR ASSEMBLY - BODY GROUND)


    C157605E04
  1. Connect the negative (-) terminal cable to the battery.

  1. Turn the power switch on (IG).

  1. Operate all components of the electrical system (defogger, wipers, headlights, heater blower, etc.).

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    D30-21 (IG2) - Body ground
    power switch on (IG)
    8 to 16 V

  1. Turn the power switch off.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    D30-25 (E1) - Body ground
    Always
    Below 1 Ω
    D30-26 (E2) - Body ground
    Always
    Below 1 Ω



NG
REPLACE WIRE HARNESS
OK


10.CHECK CONNECTOR
  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Check that the connector is properly connected to the combination meter assembly.

    OK:
    The connector is properly connected.

    HINT:
    If the connector is not connected securely, reconnect the connector and proceed to the next inspection.

  1. Disconnect the connector from the combination meter assembly.

  1. Check that the terminal of the connector is not damaged.

    OK:
    The terminal is not deformed or damaged.



NG
REPLACE WIRE HARNESS
OK


11.CHECK WIRE HARNESS (COMBINATION METER ASSEMBLY - BODY GROUND)


    E146920E14
  1. Connect the negative (-) terminal cable to the battery.

  1. Turn the power switch on (IG).

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    E1-1 (IG+) - Body ground
    Always
    11 to 14 V
    E1-21 (B) - Body ground
    power switch on (IG)
    11 to 14 V
    E1-22 (B2) - Body ground
    Always
    11 to 14 V

  1. Turn the power switch off.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    E1-20 (ES) - Body ground
    Always
    Below 1 Ω
    E1-40 (E2) - Body ground
    Always
    Below 1 Ω



NG
REPLACE WIRE HARNESS
OK


12.CHECK SRS WARNING LIGHT
  1. Connect the connector to the combination meter assembly.

  1. Connect the negative (-) terminal cable to the battery.

  1. Turn the power switch on (IG).

  1. Check the SRS warning light condition.

    OK:
    After the primary check period, the SRS warning light goes off for approximately 10 seconds and then remains on.

    HINT:
    The primary check period is for approximately 6 seconds after the power switch is turned on (IG).



NG
REPLACE COMBINATION METER ASSEMBLY (Click here)
OK

REPLACE CENTER AIRBAG SENSOR ASSEMBLY (Click here)