Home › RESTRAINTS › SUPPLEMENTAL RESTRAINT SYSTEM › AIRBAG SYSTEM

DTC    B1617/84    Lost Communication with Front Airbag Sensor LH

DTC    B1618/84    Front Airbag Sensor LH Initialization Incomplete

for Preparation Click here


DESCRIPTION

The front airbag sensor LH circuit consists of the center airbag sensor assembly and front airbag sensor LH.
The front airbag sensor LH detects impacts to the vehicle and sends signals to the center airbag sensor assembly to determine if the airbag should be deployed.
These DTCs are recorded when a malfunction is detected in the front airbag sensor LH circuit.

DTC No.
DTC Detection Condition
Trouble Area
B1617/84
B1618/84
  1. The center airbag sensor assembly receives a line short circuit signal, an open circuit signal, a short circuit to ground signal or a short circuit to B+ signal in the front airbag sensor LH circuit for 2 seconds.
  2. Front airbag sensor LH malfunction
  3. Center airbag sensor assembly malfunction
  1. Instrument panel wire
  2. Engine room main wire
  3. Front airbag sensor LH
  4. Center airbag sensor assembly

WIRING DIAGRAM


C145438E08


INSPECTION PROCEDURE

1.CHECK CONNECTORS
  1. Turn the power switch off.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Check that the connectors are properly connected to the center airbag sensor assembly and the front airbag sensor LH. Also check that the connectors that link the engine room main wire and instrument panel wire are properly connected.

    OK:
    The connectors are properly connected.

    HINT:
    If the connectors are not connected securely, reconnect the connectors and proceed to the next inspection.

  1. Disconnect the connectors from the center airbag sensor assembly and the front airbag sensor LH. Also disconnect the connectors that link the engine room main wire and instrument panel wire.

  1. Check that the terminal of the connector is not damaged.

    OK:
    The terminal is not deformed or damaged.



NG
REPLACE WIRE HARNESS
OK


2.CHECK FRONT AIRBAG SENSOR LH CIRCUIT (OPEN)


    C167945E02
  1. Connect the connectors that link the engine room main wire and instrument panel wire.

  1. Using SST, connect terminals 30 (+SL) and 28 (-SL) of connector B.

    NOTICE:
    Do not forcibly insert SST into the terminals of the connector when connecting.

SST
09843-18040  
  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    A4-2 (+SL) - A4-1 (-SL)
    Always
    Below 1 Ω



NG
Go to step 7
OK


3.CHECK FRONT AIRBAG SENSOR LH CIRCUIT (SHORT)


    C167940E04
  1. Disconnect SST from connector B.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    A4-2 (+SL) - A4-1 (-SL)
    Always
    1 MΩ or higher



NG
Go to step 8
OK


4.CHECK FRONT AIRBAG SENSOR LH CIRCUIT (SHORT TO B+)


    C167940E04
  1. Connect the negative (-) terminal cable to the battery.

  1. Turn the power switch on (IG).

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    A4-2 (+SL) - Body ground
    power switch on (IG)
    Below 1 V
    A4-1 (-SL) - Body ground
    power switch on (IG)
    Below 1 V



NG
Go to step 9
OK


5.CHECK FRONT AIRBAG SENSOR LH CIRCUIT (SHORT TO GROUND)


    C167940E04
  1. Turn the power switch off.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    A4-2 (+SL) - Body ground
    Always
    1 MΩ or higher
    A4-1 (-SL) - Body ground
    Always
    1 MΩ or higher



NG
Go to step 10
OK


6.CHECK FRONT AIRBAG SENSOR LH


    C167946E01
  1. Connect the connector to the center airbag sensor assembly.

  1. Interchange the front airbag sensor RH with LH and connect the connectors to them.

  1. Connect the negative (-) terminal cable to the battery.

  1. Turn the power switch on (IG), and wait for at least 60 seconds.

  1. Clear the DTCs stored in the memory (Click here).

  1. Turn the power switch off.

  1. Turn the power switch on (IG), and wait for at least 60 seconds.

  1. Check for DTCs (Click here).

    Result:
    Result
    Proceed to
    DTC B1612/83, B1613/83, B1617/84 and B1618/84 are not output
    A
    DTC B1617/84 or B1618/84 is output
    B
    DTC B1612/83 or B1613/83 is output
    C

    HINT:
    Codes other than DTC B1612/83, B1613/83, B1617/84 and B1618/84, may be output at this time, but they are not related to this check.



B
REPLACE CENTER AIRBAG SENSOR ASSEMBLY (Click here)

C
REPLACE FRONT AIRBAG SENSOR LH (Click here)
A

USE SIMULATION METHOD TO CHECK (Click here)  

7.CHECK INSTRUMENT PANEL WIRE (OPEN)


    C167947E02
  1. Disconnect the instrument panel wire connector from the engine room main wire.

    HINT:
    SST has already been inserted into connector B.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    AD6-1 (+SL) - AD6-2 (-SL)
    Always
    Below 1 Ω



NG
REPLACE INSTRUMENT PANEL WIRE
OK

REPLACE ENGINE ROOM MAIN WIRE 

8.CHECK INSTRUMENT PANEL WIRE (SHORT)


    C167943E04
  1. Disconnect the instrument panel wire connector from the engine room main wire.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    AD6-1 (+SL) - AD6-2 (-SL)
    Always
    1 MΩ or higher



NG
REPLACE INSTRUMENT PANEL WIRE
OK

REPLACE ENGINE ROOM MAIN WIRE 

9.CHECK INSTRUMENT PANEL WIRE (SHORT TO B+)


    C167943E04
  1. Turn the power switch off.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Disconnect the instrument panel wire connector from the engine room main wire.

  1. Connect the negative (-) terminal cable to the battery.

  1. Turn the power switch on (IG).

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    AD6-1 (+SL) - Body ground
    power switch on (IG)
    Below 1 V
    AD6-2 (-SL) - Body ground
    power switch on (IG)
    Below 1 V



NG
REPLACE INSTRUMENT PANEL WIRE
OK

REPLACE ENGINE ROOM MAIN WIRE 

10.CHECK INSTRUMENT PANEL WIRE (SHORT TO GROUND)


    C167943E04
  1. Disconnect the instrument panel wire connector from the engine room main wire.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    AD6-1 (+SL) - Body ground
    Always
    1 MΩ or higher
    AD6-2 (-SL) - Body ground
    Always
    1 MΩ or higher



NG
REPLACE INSTRUMENT PANEL WIRE
OK

REPLACE ENGINE ROOM MAIN WIRE