Home › RESTRAINTS › SUPPLEMENTAL RESTRAINT SYSTEM › AIRBAG SYSTEM

DTC    B1653/35    Seat Position Airbag Sensor Circuit Malfunction

for Preparation Click here


DESCRIPTION

The seat position airbag sensor circuit consists of the center airbag sensor assembly and the seat position airbag sensor.
DTC B1653/35 is recorded when a malfunction is detected in the seat position airbag sensor circuit.

DTC No.
DTC Detection Condition
Trouble Area
B1653/35
  1. The center airbag sensor assembly receives a line short circuit signal, an open circuit signal, a short circuit to ground signal or a short circuit to B+ signal in the seat position airbag sensor circuit for 2 seconds.
  2. Front seat inner belt assembly LH malfunction
  3. Seat position airbag sensor malfunction
  4. Center airbag sensor assembly malfunction
  1. Floor wire No. 2
  2. Front seat inner belt assembly LH
  3. Seat position airbag sensor
  4. Center airbag sensor assembly

WIRING DIAGRAM


C167962E05


INSPECTION PROCEDURE

1.CHECK CONNECTORS
  1. Turn the power switch off.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Check that the connectors are properly connected to the center airbag sensor assembly, front seat inner belt assembly LH and the seat position airbag sensor.

    OK:
    The connectors are properly connected.

    HINT:
    If the connectors are not connected securely, reconnect the connectors and proceed to the next inspection.

  1. Disconnect the connectors from the center airbag sensor assembly, front seat inner belt assembly LH and the seat position airbag sensor.

  1. Check that the terminals of the connectors are not damaged.

    OK:
    The terminals are not deformed or damaged.



NG
REPLACE WIRE HARNESS
OK


2.CHECK FLOOR WIRE NO. 2 (OPEN)


  1. Connect the connectors to the front seat inner belt assembly LH and floor wire No. 2.


    C169190E02

  1. Using SST, connect terminals 9 (DSP+) and 17 (DSP-) of connector B.

    NOTICE:
    Do not forcibly insert SST into the terminals of the connector when connecting the wire.

SST
09843-18040  
  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    2 (LSP+) - 1 (LSP-)
    Always
    Below 1 Ω



NG
Go to step 9
OK


3.CHECK FLOOR WIRE NO. 2 (SHORT)


    C169191E02
  1. Disconnect SST from connector B.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    2 (LSP+) - 1 (LSP-)
    Always
    1 MΩ or higher



NG
Go to step 10
OK


4.CHECK FLOOR WIRE NO. 2 (SHORT TO B+)


    C169191E02
  1. Connect the negative (-) terminal cable to the battery.

  1. Turn the power switch on (IG).

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    2 (LSP+) - Body ground
    power switch on (IG)
    Below 1 V
    1 (LSP-) - Body ground
    power switch on (IG)
    Below 1 V



NG
Go to step 11
OK


5.CHECK FLOOR WIRE NO. 2 (SHORT TO GROUND)


    C169191E02
  1. Turn the power switch off.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    2 (LSP+) - Body ground
    Always
    1 MΩ or higher
    1 (LSP-) - Body ground
    Always
    1 MΩ or higher



NG
Go to step 12
OK


6.CHECK SEAT POSITION AIRBAG SENSOR


    C168011E01
  1. Connect the connectors to the center airbag sensor assembly and the seat position airbag sensor.

  1. Connect the negative (-) terminal cable to the battery.

  1. Turn the power switch on (IG), and wait for at least 60 seconds.

  1. Clear the DTCs stored in the memory (Click here).

  1. Turn the power switch off.

  1. Turn the power switch on (IG), and wait for at least 60 seconds.

  1. Check for DTCs (Click here).

    OK:
    DTC B1653/35 is not output.

    HINT:
    Codes other than DTC B1653/35 may be output at this time, but they are not related to this check.



NG
Go to step 7
OK

USE SIMULATION METHOD TO CHECK (Click here)  

7.REPLACE SEAT POSITION AIRBAG SENSOR
  1. Turn the power switch off.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Replace the seat position airbag sensor (Click here).

    HINT:
    Perform inspection using parts from a normal vehicle if possible.


NEXT


8.CHECK CENTER AIRBAG SENSOR ASSEMBLY


    C168011E01
  1. Connect the negative (-) terminal cable to the battery.

  1. Turn the power switch on (IG), and wait for at least 60 seconds.

  1. Clear the DTCs stored in the memory (Click here).

  1. Turn the power switch off.

  1. Turn the power switch on (IG), and wait for at least 60 seconds.

  1. Check for DTCs (Click here).

    OK:
    DTC B1653/35 is not output.

    HINT:
    Codes other than DTC B1653/35 may be output at this time, but they are not related to this check.



NG
REPLACE CENTER AIRBAG SENSOR ASSEMBLY (Click here)
OK

END 

9.CHECK FLOOR WIRE NO. 2 (OPEN)
  1. Disconnect the floor wire No. 2 from front seat inner belt assembly LH.

    HINT:
    SST has already been inserted into connector B.


C170256E01

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    O10-2 (LSP+) - O10-4 (LSP-)
    Always
    Below 1 Ω



NG
REPLACE FLOOR WIRE NO. 2
OK

REPLACE FRONT SEAT INNER BELT ASSEMBLY LH (Click here)  

10.CHECK FLOOR WIRE NO. 2 (SHORT)
C171456E01
  1. Disconnect the floor wire No. 2 from front seat belt inner belt assembly LH.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    O10-2 (LSP+) - O10-4 (LSP-)
    Always
    1 MΩ or higher



NG
REPLACE FLOOR WIRE NO. 2
OK

REPLACE FRONT SEAT INNER BELT ASSEMBLY LH (Click here)  

11.CHECK FLOOR WIRE NO. 2 (SHORT TO B+)


    C171456E01
  1. Turn the power switch off.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Disconnect the floor wire No. 2 from front seat inner belt assembly LH.

  1. Connect the negative (-) terminal cable to the battery.

  1. Turn the power switch on (IG).

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    O10-2 (LSP+) - Body ground
    power switch on (IG)
    Below 1 V
    O10-4 (LSP-) - Body ground
    power switch on (IG)
    Below 1 V



NG
REPLACE FLOOR WIRE NO. 2
OK

REPLACE FRONT SEAT INNER BELT ASSEMBLY LH (Click here)  

12.CHECK FLOOR WIRE NO. 2 (SHORT TO GROUND)
C171456E01
  1. Disconnect the floor wire No. 2 from front seat inner belt assembly LH.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    O10-2 (LSP+) - Body ground
    Always
    1 MΩ or higher
    O10-4 (LSP-) - Body ground
    Always
    1 MΩ or higher



NG
REPLACE FLOOR WIRE NO. 2
OK

REPLACE FRONT SEAT INNER BELT ASSEMBLY LH (Click here)