Home › BRAKE › BRAKE CONTROL › ELECTRONICALLY CONTROLLED BRAKE SYSTEM

DTC    U0073/94    Control Module Communication Bus OFF

DTC    U0123/62    Lost Communication with Yaw Rate Sensor Module

DTC    U0124/95    Lost Communication with Lateral Acceleration Sensor Module

DTC    U0126/63    Lost Communication with Steering Angle Sensor Module

DTC    U0293/59    Communication Error from HV ECU

for Preparation Click here


DESCRIPTION

The skid control ECU receives the signals from the hybrid vehicle control ECU, steering angle sensor, and yaw rate and acceleration sensor via the CAN communication system.

DTC Code
INF Code
DTC Detection Condition
Trouble Area
U0073/94
360
Either of the following is detected:
  1. After the output of data from the skid control ECU is completed, the data continues to be sent for 5 seconds or more.
  2. Bus OFF state occurs once or more within 0.1 seconds 10 times in succession. (Sent signals cannot be received.)
CAN communication system
U0123/62
338
Either of the following is detected:
  1. With the IG1 terminal voltage 10 V or more, data from the yaw rate sensor cannot be received for 1 second or more.
  2. With the IG1 terminal voltage 10 V or more, the following occurs 10 times in succession:
  1. Data from the yaw rate sensor cannot be received once or more within 5 seconds.
CAN communication system
(Skid control ECU to yaw rate and acceleration sensor)
U0124/95
319
Either of the following is detected:
  1. With the IG1 terminal voltage 9.5 V or more, data from the acceleration sensor cannot be received for 1 second or more.
  2. With the IG1 terminal voltage 9.5 V or more, the following occurs 10 times in succession:
  1. Data from the acceleration sensor cannot be received once or more within 5 seconds.
CAN communication system
(Skid control ECU to yaw rate and acceleration sensor)
U0126/63
350
Either of the following is detected:
  1. With the IG1 terminal voltage 10 V or more, data from the steering sensor cannot be received for 1 second or more.
  2. With the IG1 terminal voltage 10 V or more, the following occurs 10 times in succession:
  1. Data from the steering angle sensor cannot be received once or more within 5 seconds.
CAN communication system
(Skid control ECU to steering angle sensor)
U0293/59
152
With the IG2 terminal voltage at 9.5 V or more for 2 seconds or more, communication with the hybrid vehicle control ECU remains invalid for 2 seconds or more.
CAN communication system
(Skid control ECU to hybrid vehicle control ECU)
↑
153
With the IG2 terminal voltage at 9.5 V or more for 2 seconds or more, communication with the hybrid vehicle control ECU changes from valid to invalid occurs once or more within 5 seconds 10 times or more within 1 minute.
↑
↑
155
With the IG2 terminal voltage at 9.5 V or more for 2 seconds or more, abnormal regenerative braking torque value or braking request torque value is received for 2 seconds or more.
↑

WIRING DIAGRAM


C174061E01


INSPECTION PROCEDURE

1.CHECK HARNESS AND CONNECTOR (MOMENTARY INTERRUPTION)
  1. Using the Techstream, check for any momentary interruptions in the wire harness and connector corresponding to a DTC (Click here).

    ABS / VSC / TRAC: 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    HV Communication Open
    Hybrid vehicle communication open detection / ERROR or NORMAL
    ERROR: Momentary interruption
    NORMAL: Normal
    -
    Steering Open
    Steering angle sensor open detection / ERROR or NORMAL
    ERROR: Momentary interruption
    NORMAL: Normal
    -
    Yaw Rate Open
    Yaw rate sensor open detection / ERROR or NORMAL
    ERROR: Momentary interruption
    NORMAL: Normal
    -

    Result:

    Result
    Proceed to
    There is a constant open circuit
    A
    There are no momentary interruptions
    B
    There are momentary interruptions
    C

    HINT:
    Perform the above inspection before removing any sensor or connector.



B
Go to step 3

C
Go to step 4
A


2.CHECK IF EACH SENSOR AND ECU CONNECTOR ARE SECURELY CONNECTED
  1. Turn the power switch off.

  1. Check if each sensor and ECU connector are securely connected.

    OK:
    Each sensor and ECU connector are securely connected.



NG
CONNECT CONNECTOR TO EACH SENSOR OR ECU CORRECTLY
OK


3.RECONFIRM DTC
  1. Turn the power switch off.

  1. Record the output DTCs (for ABS, VSC, electronically controlled brake system, and/or CAN communication system) (Click here for ABS, VSC and/or electronically controlled brake system, or Click here for CAN communication system).

    HINT:
    If the CAN communication system DTC and the relevant sensor DTCs are output simultaneously, troubleshoot the relevant sensor DTCs (for ABS, VSC and/or electronically controlled brake system) after the CAN communication system returns to normal.


    Result:

    Result
    Proceed to
    DTC is not output
    A
    DTC (ABS, VSC and/or electronically controlled brake system DTC) is output
    B
    DTC (CAN communication system DTC) is output
    C



B
REPAIR CIRCUIT INDICATED BY OUTPUT DTC (Click here)

C
INSPECT CAN COMMUNICATION SYSTEM (Click here)
A

CHECK FOR INTERMITTENT PROBLEMS (SYMPTOM SIMULATION) (Click here)  

4.REPAIR OR REPLACE HARNESS OR CONNECTOR
  1. Turn the power switch off.

  1. Repair or replace the harness or connector.

  1. Check for any momentary interruption between the skid control ECU and each sensor or ECU (Click here).

  1. Check that there are no momentary interruptions.


NEXT


5.RECONFIRM DTC
  1. Turn the power switch off.

  1. Clear the DTCs (Click here).

  1. Turn the power switch on (READY).

  1. Drive the vehicle and turn the steering wheel to the right and left at a speed of 15 km/h (9 mph) or more.

  1. Check that no CAN communication system DTC is output (Click here).

  1. If ABS, VSC and/or electronically controlled brake system DTCs are output, record them (Click here).

    Result:

    Result
    Proceed to
    DTC is not output
    A
    DTC (ABS, VSC and/or electronically controlled brake system DTC) is output
    B
    DTC (CAN communication system DTC) is output
    C

    HINT:
    The CAN communication system must be normal when repairing each sensor DTC (for ABS, VSC and/or electronically controlled brake system).



B
REPAIR CIRCUIT INDICATED BY OUTPUT DTC (Click here)

C
INSPECT CAN COMMUNICATION SYSTEM (Click here)
A

END