Home › HYBRID SYSTEM · P310 › HYBRID VEHICLE CONTROL › HYBRID CONTROL SYSTEM

DTC    P3004-800    Power Cable Malfunction

DTC    P3004-801    Power Cable Malfunction

for Preparation Click here


DESCRIPTION

The hybrid vehicle control ECU monitors the high-voltage wiring between the HV battery and inverter with converter assembly and detects the following malfunction.

DTC No.
INF Code
DTC Detection Condition
Trouble Area
P3004
800
Excessive overcurrent occurs during precharge (time from when SMR1 turns on until when SMR2 turns on)
  1. Wire harness or connector
  2. No. 4 Engine wire
  3. With motor compressor assembly
  4. Inverter with converter assembly
  5. HV relay assembly
  6. No. 3 frame wire
801
Minimal overcurrent occurs during precharge (time from when SMR1 turns on until when SMR2 turns on)

WIRING DIAGRAM

  1. Refer to the wiring diagram for DTC P0A08-264 and DTC P0AE6-225 .

INSPECTION PROCEDURE

CAUTION:
  1. Before inspecting the high-voltage system or disconnecting the low voltage connector of the inverter with converter assembly, take safety precautions such as wearing insulated gloves and removing the service plug grip to prevent electrical shocks. After removing the service plug grip, put it in your pocket to prevent other technicians from accidentally reconnecting it while you are working on the high-voltage system.
  2. After disconnecting the service plug grip, wait for at least 5 minutes before touching any of the high-voltage connectors or terminals. After waiting for 5 minutes, check the voltage at the terminals in the inspection point in the inverter with converter assembly. The voltage should be 0 V before beginning work.

HINT:
Waiting for at least 5 minutes is required to discharge the high-voltage capacitor inside the inverter with converter assembly.

1.CHECK DTC OUTPUT (HV)
  1. Connect the Techstream to the DLC3.

  1. Turn the power switch on (IG).

  1. Select the following menu items: Powertrain / Hybrid Control / Trouble Codes.

    Result:
    Result
    Proceed to
    P3004-800 or P3004-801 only is output.
    A
    Any of the following DTCs are also output.
    B

    DTC No.
    Relevant Diagnosis
    P0A09 (all INF codes) *1
    DC / DC Converter Status Circuit Low Input
    P0A10 (all INF codes) *1
    DC / DC Converter Status Circuit High Input

    HINT:
    *1: If any INF codes are output for this DTC, refer to the corresponding diagnostic flowchart.



B
GO TO DTC CHART (Click here)
A


2.CHECK WIRE HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU - MG ECU)

CAUTION:
Be sure to wear insulated gloves.

  1. Turn the power switch off.

  1. Remove the service plug grip (Click here).

    NOTICE:
    After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.

  1. Disconnect the A43 connector from the hybrid vehicle control ECU.

  1. Remove the inverter cover (Click here).

    NOTICE:
    1. Wrap the round interlock terminal for the inverter cover with insulating tape to prevent it from shorting to ground.
    2. Be sure to prevent coolant in the inverter reserve tank from entering the inverter.
    3. Removing the inverter cover causes the MG ECU board to be exposed. Therefore, temporarily install the inverter cover for each area to be inspected.

  1. Disconnect the A42 connector from the MG ECU.



    A175145E07
  1. Measure the voltage according to the value(s) in the table below when the power switch is on (IG).

    HINT:
    Turning the power switch on (IG) with the service plug grip and inverter cover removed causes interlock switch system DTC (P0A0D-350) to be set.

    Standard voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    A43-11 (NODD) - Body ground
    Power switch on (IG)
    Below 1 V

  1. Turn the power switch off.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance (Check for open):
    Tester Connection
    Switch Condition
    Specified Condition
    A43-11 (NODD) - A42-33 (NODD)
    Power switch off
    Below 1 Ω

    Standard resistance (Check for short):
    Tester Connection
    Switch Condition
    Specified Condition
    A43-11 (NODD) or A42-33 (NODD) - Body ground and other terminals
    Power switch off
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3.CHECK WITH MOTOR COMPRESSOR ASSEMBLY

CAUTION:
Be sure to wear insulated gloves.

  1. Check that the service plug grip is not installed.



    A175130E01
  1. Disconnect the No. 4 engine wire from the air conditioning wiring harness.

    NOTICE:
    Do not remove the bolt for the No. 4 engine wire shielded wire from the inverter with converter assembly.



    A175149E01
  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    1 (+) - 2 (-)
    Power switch off
    100 Ω or higher

    NOTICE:
    Connect the tester correctly.



NG
Go to step 6
OK


4.CHECK NO. 3 FRAME WIRE

CAUTION:
Be sure to wear insulated gloves.



    A175132E01
  1. Disconnect the No. 3 frame wire (DC cable for the HV battery) from the inverter with converter assembly.



    A108046E07
  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    1 (+) - 2 (-)
    Power switch off
    10 kΩ or higher

    NOTICE:
    Connect the tester correctly.



NG
Go to step 5
OK

REPLACE INVERTER WITH CONVERTER ASSEMBLY (Click here)  

5.CHECK NO. 3 FRAME WIRE (INVERTER WITH CONVERTER ASSEMBLY - HV RELAY ASSEMBLY)

CAUTION:
Be sure to wear insulated gloves.



    A108041E07
  1. Disconnect the No. 3 frame wire (DC cable for the inverter with converter assembly) from the HV relay assembly.



    A117156E04
  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    j2-1 - j3-1
    Power switch off
    10 kΩ or higher



NG
REPLACE NO. 3 FRAME WIRE
OK

REPLACE HV RELAY ASSEMBLY (Click here)  

6.CHECK NO. 4 ENGINE WIRE

CAUTION:
Be sure to wear insulated gloves.



    A108067E01
  1. Disconnect the No. 4 engine wire from the with motor compressor assembly.



    A175149E01
  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    1 - 2
    Power switch off
    10 kΩ or higher



NG
REPLACE NO. 4 ENGINE WIRE
OK

REPLACE WITH MOTOR COMPRESSOR ASSEMBLY (Click here)