Home › RESTRAINTS › SUPPLEMENTAL RESTRAINT SYSTEM › OCCUPANT CLASSIFICATION SYSTEM

DTC    B1771    Passenger Side Buckle Switch Circuit Malfunction

for Preparation Click here


DESCRIPTION

The passenger side buckle switch circuit consists of the occupant classification ECU and the front seat inner belt assembly RH.
DTC B1771 is recorded when a malfunction is detected in the passenger side buckle switch circuit.
Troubleshoot DTC B1771 first if DTCs B1771 and B1795 are output simultaneously.

DTC No.
DTC Detection Condition
Trouble Area
B1771
  1. The occupant classification ECU receives a line short circuit signal, an open circuit signal, a short circuit to ground signal or a short circuit to B+ signal in the passenger side buckle switch circuit for 2 seconds.
  2. Passenger side buckle switch malfunction
  3. Occupant classification ECU malfunction
  1. Front seat inner belt assembly RH (Passenger side buckle switch)
  2. Occupant classification ECU
  3. Front seat wire RH

HINT:
When DTC B1650/32 is detected as a result of troubleshooting for the AIRBAG SYSTEM, check the DTCs stored in the occupant classification ECU. When DTC B1771 in output, perform troubleshooting for the DTC.


WIRING DIAGRAM


C167968E04


INSPECTION PROCEDURE

HINT:
  1. If troubleshooting (wire harness inspection) is difficult to perform, remove the front passenger seat installation bolts to see under the seat cushion.
  2. In the above case, hold the seat so that it does not fall down. Hold the seat only as necessary because holding the seat for a long period of time may cause seat rail deformation.

1.CHECK CONNECTORS
  1. Turn the power switch off.

  1. Disconnect the negative (-) terminal cable from the battery.

  1. Check that the connectors are properly connected to the occupant classification ECU and the front seat inner belt assembly RH.

    OK:
    The connectors are properly connected.

    HINT:
    If the connectors are not connected securely, reconnect the connectors and proceed to the next inspection.

  1. Disconnect the connectors from the occupant classification ECU and the front seat inner belt assembly RH.

  1. Check that the terminals of the connectors are not damaged.

    OK:
    The terminals are not deformed or damaged.



NG
REPLACE FRONT SEAT WIRE RH
OK


2.CHECK FRONT SEAT WIRE RH (SHORT TO B+)


    C169183E01
  1. Connect the negative (-) terminal cable to the battery.

  1. Turn the power switch on (IG).

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    a3-9 (BSW) - Body ground
    power switch on (IG)
    Below 1 V
    a3-5 (BGND) - Body ground
    power switch on (IG)
    Below 1 V



NG
REPLACE FRONT SEAT WIRE RH
OK


3.CHECK FRONT SEAT WIRE RH (OPEN)


  1. Turn the power switch off.


    C178311E01

  1. Disconnect the negative (-) terminal cable from the battery.

  1. Using SST, connect terminals 2 and 1 of connector C.

    NOTICE:
    Do not forcibly insert SST into the terminals of the connector when connecting.

SST
09843-18040  
  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    a3-9 (BSW) - a3-5 (BGND)
    Always
    Below 1 Ω



NG
REPLACE FRONT SEAT WIRE RH
OK


4.CHECK FRONT SEAT WIRE RH (SHORT)


    C169183E01
  1. Disconnect SST from connector C.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    a3-9 (BSW) - a3-5 (BGND)
    Always
    1 MΩ or higher



NG
REPLACE FRONT SEAT WIRE RH
OK


5.CHECK FRONT SEAT WIRE RH (SHORT TO GROUND)


    C169183E01
  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    a3-9 (BSW) - Body ground
    Always
    1 MΩ or higher
    a3-5 (BGND) - Body ground
    Always
    1 MΩ or higher



NG
REPLACE FRONT SEAT WIRE RH
OK


6.CHECK DTC
  1. Connect the connectors to the occupant classification ECU and the front seat inner belt assembly RH.

  1. Connect the negative (-) terminal cable to the battery.

  1. Turn the power switch on (IG).

  1. Clear the DTCs stored in the occupant classification ECU (Click here).

  1. Clear the DTCs stored in the center airbag sensor assembly (Click here).

  1. Turn the power switch off.

  1. Turn the power switch on (IG).

  1. Check for DTCs (Click here).

    OK:
    DTC B1771 is not output.

    HINT:
    Codes other than DTC B1771 may be output at this time, but they are not related to this check.



NG
Go to step 7
OK

USE SIMULATION METHOD TO CHECK (Click here)  

7.REPLACE FRONT SEAT INNER BELT ASSEMBLY RH
  1. Turn the power switch off.

  1. Disconnect the negative (-) terminal cable from the battery.

  1. Replace the front seat inner belt assembly RH (Click here).

    HINT:
    Perform the inspection using parts from a normal vehicle if possible.

  1. Connect the negative (-) terminal cable to the battery.

  1. Turn the power switch on (IG).

  1. Clear the DTCs stored in the occupant classification ECU (Click here).

  1. Clear the DTCs stored in the center airbag sensor assembly (Click here).

  1. Turn the power switch off.

  1. Turn the power switch on (IG).

  1. Check for DTCs (Click here).

    OK:
    DTC B1771 is not output.

    HINT:
    Codes other than DTC B1771 may be output at this time, but they are not related to this check.



NG
Go to step 8
OK

END 

8.REPLACE OCCUPANT CLASSIFICATION ECU
  1. Turn the power switch off.

  1. Disconnect the negative (-) terminal cable from the battery.

  1. Replace the occupant classification ECU (Click here).


NEXT


9.PERFORM ZERO POINT CALIBRATION
  1. Connect the negative (-) terminal cable to the battery.

  1. Connect Techstream to the DLC3.

  1. Turn the power switch on (IG).

  1. Using Techstream, perform "zero point calibration" (Click here).

    OK:
    "Zero Point Calibration is complete." is displayed.


NEXT


10.PERFORM SENSITIVITY CHECK
  1. Using Techstream, perform "sensitivity check" (Click here).

    Standard:
    27 to 33 kg (59.52 to 72.75 lb)


NEXT

END