Home › RESTRAINTS › SUPPLEMENTAL RESTRAINT SYSTEM › OCCUPANT CLASSIFICATION SYSTEM

DTC    B1793    Occupant Classification Sensor Power Supply Circuit Malfunction

for Preparation Click here


DESCRIPTION

The occupant classification sensor power supply circuit consists of the occupant classification ECU and the occupant classification sensors.
DTC B1793 is recorded when a malfunction is detected in the occupant classification sensor power supply circuit.

DTC No.
DTC Detection Condition
Trouble Area
B1793
  1. The occupant classification ECU receives a line short circuit signal, an open circuit signal, a short circuit to ground signal or a short circuit to B+ signal in the occupant classification sensor power supply circuit for 2 seconds.
  2. Occupant classification ECU malfunction
  1. Front seat assembly RH (Occupant classification sensors)
  2. Occupant classification ECU
  3. Front seat wire RH

HINT:
When DTC B1650/32 is detected as a result of troubleshooting for the AIRBAG SYSTEM, check the DTCs stored in the occupant classification ECU. When DTC B1793 is output, perform troubleshooting for the DTC.


WIRING DIAGRAM


C170483E01


INSPECTION PROCEDURE

HINT:
  1. If troubleshooting (wire harness inspection) is difficult to perform, remove the front passenger seat installation bolts to see under the seat cushion.
  2. In the above case, hold the seat so that it does not fall down. Hold the seat only as necessary because holding the seat for a long period of time may cause seat rail deformation.

1.CHECK CONNECTORS
  1. Turn the power switch off.

  1. Disconnect the negative (-) terminal cable from the battery.

  1. Check that the connectors are properly connected to the center airbag sensor assembly and the occupant classification ECU.

    OK:
    The connectors are properly connected.

    HINT:
    If the connectors are not connected securely, reconnect the connectors and proceed to the next inspection.

  1. Disconnect the connectors from the center airbag sensor assembly and the occupant classification ECU.

  1. Check that the terminals of the connectors are not damaged.

    OK:
    The terminals are not deformed or damaged.



NG
REPLACE FRONT SEAT WIRE RH
OK


2.CHECK FRONT SEAT WIRE RH (SHORT TO B+)


    C169182E01
  1. Connect the negative (-) terminal cable to the battery.

  1. Turn the power switch on (IG).

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    a1-5 (SVC3) - Body ground
    power switch on (IG)
    Below 1 V
    a1-6 (SVC4) - Body ground
    power switch on (IG)
    Below 1 V
    a1-11 (SVC1) - Body ground
    power switch on (IG)
    Below 1 V
    a1-12 (SVC2) - Body ground
    power switch on (IG)
    Below 1 V



NG
REPLACE FRONT SEAT WIRE RH
OK


3.CHECK FRONT SEAT WIRE RH (SHORT TO GROUND)


    C169182E01
  1. Turn the power switch off.

  1. Disconnect the negative (-) terminal cable from the battery.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    a1-5 (SVC3) - Body ground
    Always
    1 MΩ or higher
    a1-6 (SVC4) - Body ground
    Always
    1 MΩ or higher
    a1-11 (SVC1) - Body ground
    Always
    1 MΩ or higher
    a1-12 (SVC2) - Body ground
    Always
    1 MΩ or higher



NG
REPLACE FRONT SEAT WIRE RH
OK


4.CHECK FRONT SEAT WIRE RH (OPEN)


    C171185E02
  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    a1-5 (SVC3) - a10-1 (SVC3)
    Always
    Below 1 Ω
    a1-6 (SVC4) - a8-1 (SVC4)
    Always
    Below 1 Ω
    a1-11 (SVC1) - a9-1 (SVC1)
    Always
    Below 1 Ω
    a1-12 (SVC2) - a7-1 (SVC2)
    Always
    Below 1 Ω



NG
REPLACE FRONT SEAT WIRE RH
OK


5.CHECK FRONT SEAT WIRE RH (SHORT)


    C169182E01
  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    a1-5 (SVC3) - a1-6 (SVC4)
    Always
    1 MΩ or higher
    a1-5 (SVC3) - a1-11 (SVC1)
    Always
    1 MΩ or higher
    a1-5 (SVC3) - a1-12 (SVC2)
    Always
    1 MΩ or higher
    a1-6 (SVC4) - a1-11 (SVC1)
    Always
    1 MΩ or higher
    a1-6 (SVC4) - a1-12 (SVC2)
    Always
    1 MΩ or higher
    a1-11 (SVC1) - a1-12 (SVC2)
    Always
    1 MΩ or higher



NG
REPLACE FRONT SEAT WIRE RH
OK


6.CHECK DTC
  1. Connect the connectors to the occupant classification ECU and the 4 occupant classification sensors.

  1. Connect the negative (-) terminal cable to the battery.

  1. Turn the power switch on (IG).

  1. Clear the DTCs stored in the occupant classification ECU (Click here).

  1. Clear the DTCs stored in the center airbag sensor assembly (Click here).

  1. Turn the power switch off.

  1. Turn the power switch on (IG).

  1. Check for DTCs (Click here).

    OK:
    DTC B1793 is not output.

    HINT:
    Codes other than DTC B1793 may be output at this time, but they are not related to this check.



NG
Go to step 7
OK

USE SIMULATION METHOD TO CHECK (Click here)  

7.REPLACE OCCUPANT CLASSIFICATION ECU
  1. Turn the power switch off.

  1. Disconnect the negative (-) terminal cable from the battery.

  1. Replace the occupant classification ECU (Click here).

    HINT:
    Perform the inspection using parts from a normal vehicle if possible.


NEXT


8.PERFORM ZERO POINT CALIBRATION
  1. Connect the negative (-) terminal cable to the battery.

  1. Connect Techstream to the DLC3.

  1. Turn the power switch on (IG).

  1. Using Techstream, perform "zero point calibration" (Click here).

    OK:
    "Zero Point Calibration is complete." is displayed.



NG
Go to step 11
OK


9.PERFORM SENSITIVITY CHECK
  1. Using Techstream, perform "sensitivity check" (Click here).

    Standard:
    27 to 33 kg (59.52 to 72.75 lb)



NG
Go to step 11
OK


10.CHECK DTC
  1. Turn the power switch on (IG).

  1. Clear the DTCs stored in the occupant classification ECU (Click here).

  1. Clear the DTCs stored in the center airbag sensor assembly (Click here).

  1. Turn the power switch off.

  1. Turn the power switch on (IG).

  1. Check for DTCs (Click here).

    OK:
    DTC B1793 is not output.

    HINT:
    Codes other than DTC B1793 may be output at this time, but they are not related to this check.



NG
Go to step 11
OK

END 

11.REPLACE FRONT SEAT ASSEMBLY RH
  1. Turn the power switch off.

  1. Disconnect the negative (-) terminal cable from the battery.

  1. Replace the front seat assembly RH (Click here for power seat or Click here for manual seat).


NEXT


12.PERFORM ZERO POINT CALIBRATION
  1. Connect the negative (-) terminal cable to the battery.

  1. Connect Techstream to the DLC3.

  1. Turn the power switch on (IG).

  1. Using Techstream, perform "zero point calibration" (Click here).

    OK:
    "Zero Point Calibration is complete." is displayed.


NEXT


13.PERFORM SENSITIVITY CHECK
  1. Using Techstream, perform "sensitivity check" (Click here).

    Standard:
    27 to 33 kg (59.52 to 72.75 lb)


NEXT

END