Home › BODY › WINDSHIELD / WINDOWGLASS › POWER WINDOW CONTROL SYSTEM

POWER WINDOW CONTROL SYSTEM > Front Passenger Side Power Window does not Operate with Front Passenger Side Power Window Switch

for Preparation Click here


DESCRIPTION

If the passenger side manual UP/DOWN function does not operate, a malfunction may exist in the power window regulator motor, power window regulator switch, power window regulator master switch or wire harness.

WIRING DIAGRAM


B175981E02


INSPECTION PROCEDURE

1.CHECK POWER WINDOW SWITCH (FRONT PASSENGER SIDE) (POWER SOURCE)


    B175982E02
  1. Disconnect the G7 connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Condition
    Specified Condition
    G7-3 (B) - Body ground
    Power switch on (IG)
    11 to 14 V



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


2.INSPECT POWER WINDOW SWITCH (FRONT PASSENGER SIDE)


    B164433E05
  1. Measure the resistance when the switch is operated according to the value(s) in the table below.

Standard resistance:
Tester Connection
Switch Condition
Specified Condition
1 (D) - 2 (SD)
UP
Below 1 Ω
3 (B) - 4 (U)
UP
Below 1 Ω
1 (D) - 2 (SD)
OFF
Below 1 Ω
4 (U) - 5 (SU)
OFF
Below 1 Ω
4 (U) - 5 (SU)
DOWN
Below 1 Ω
1 (D) - 3 (B)
DOWN
Below 1 Ω



NG
REPLACE POWER WINDOW SWITCH (FRONT PASSENGER SIDE) (Click here)
OK


3.CHECK HARNESS AND CONNECTOR (SWITCH (FRONT PASSENGER SIDE) - MOTOR (FRONT PASSENGER SIDE))


    B175983E02
  1. Disconnect the G7 and G1 connectors.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    G7-4 (U) - G1-2 (U)
    Always
    Below 1 Ω
    G7-1 (D) - G1-1 (D)
    Always
    Below 1 Ω
    G7-4 (U) - Body ground
    Always
    10 kΩ or higher
    G7-1 (D) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4.INSPECT POWER WINDOW REGULATOR MOTOR ASSEMBLY (FRONT PASSENGER SIDE)


  1. Check power window regulator motor operation.



      B164426E03
    1. Remove the power window regulator motor. (Click here)

    2. Apply battery voltage to the motor connector according to the table below.

      NOTICE:
      Do not apply battery voltage to any terminals except terminals 1 and 2.

      OK:
      Measurement Condition
      Specified Condition
      Battery negative (-) → Terminal 2
      Battery positive (+) → Terminal 1
      Motor gear rotates clockwise
      Battery negative (-) → Terminal 1
      Battery positive (+) → Terminal 2
      Motor gear rotates counterclockwise



  1. Check PTC operation:

    NOTICE:
    The work must be performed with the power window regulator and door glass installed on the vehicle.

    1. Install the power window regulator motor. (Click here)



    2. B164428E14
    3. Connect an electrical tester DC 400 A probe to the wire harness of terminal 2.

      NOTICE:
      Match the arrow mark of the probe with the direction of the current flow.

    4. Fully close the door glass by pressing the power window UP switch. Wait for approximately 60 seconds.

    5. Continue to press the power window UP switch and measure how long it takes for the electrical current to change from a range of 16 to 28 A to approximately 1 A (Inspection of current shut-off).

      Standard:
      4 to 90 seconds

    6. 60 seconds after the previous step, press the power window DOWN switch (passenger side).

      OK:
      The passenger side window goes down.



NG
REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY (FRONT PASSENGER SIDE) (Click here)
OK


5.CHECK HARNESS AND CONNECTOR (MASTER SWITCH - SWITCH (FRONT PASSENGER SIDE))


    B175975E01
  1. Disconnect the M1 and G7 connectors.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    M1-16 (U) - G7-5 (SU)
    Always
    Below 1 Ω
    M1-15 (D) - G7-2 (SD)
    Always
    Below 1 Ω
    M1-16 (U) - Body ground
    Always
    10 kΩ or higher
    M1-15 (D) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE POWER WINDOW MASTER SWITCH (Click here)