Home › ENGINE › 3MZ-FE ENGINE MECHANICAL › CAMSHAFT (for Bank 1)

CAMSHAFT (for Bank 1) > INSTALLATION

for Preparation Click here



1. INSTALL CAMSHAFT SUB GEAR


    P012595E01
  1. Clamp the camshaft in a vise on the hexagonal lobe.

    NOTICE:
    Do not damage the camshaft.



    A180234E01
  1. Install the camshaft gear bolt washer and the camshaft sub-gear.

    HINT:
    Attach the pins on the gears to the gear bolt washer ends.

  1. Install the wave washer.



    A052353E01
  1. Using snap ring pliers, install the snap ring.



    A078733E01
  1. Using SST, align the holes of the camshaft main gear and sub-gear by turning the camshaft sub-gear counterclockwise, and temporarily install a service bolt.

    SST
    09960-10010   (09962-01000, 09963-00500)

  1. Align the gear teeth of the main gear and sub-gear, and tighten the service bolt.

    Torque:
    5.0 N*m{ 51 kgf*cm , 44 in.*lbf }

    NOTICE:
    Do not damage the camshaft.

    HINT:
    When installing the camshaft, make certain that the torsional spring force of the sub-gear has been eliminated by installing the service bolt.



2. INSTALL CAMSHAFT TIMING GEAR ASSEMBLY


    A078734E01
  1. Align the alignment pin with the groove and install the camshaft timing gear on the camshaft.

    NOTICE:
    Install it with the lock-pin engaged and locked at the most retard angle position.

  1. Apply engine oil to the nut, the mounting surface of the camshaft timing gear and the screw threads.

    NOTICE:
    1. Be sure to apply oil, otherwise the specified torque cannot be obtained.
    2. A new nut must be used when replacing the camshaft timing gear unit.



    A005738E01
  1. Using a 46 mm socket wrench, install and tighten a lock nut by turning it counterclockwise.

    Torque:
    150 N*m{ 1530 kgf*cm , 111 ft.*lbf }

    NOTICE:
    1. The lock nut has left-hand threads.
    2. Never use any tool other than the socket wrench. Other tools will deform the cam angle rotor.



3. INSTALL NO. 2 CAMSHAFT

NOTICE:
Since the thrust clearance of the camshaft is small, the camshaft must be kept level while it is being installed. If the camshaft is not kept level, damage to the cylinder head or to the camshaft may result. To avoid this, the following steps should be carried out.

  1. Apply new engine oil to the thrust portion and journal of the camshaft.



    A078735E01
  1. Place the No. 2 camshaft at 90° angle of the timing mark (2-dot mark) on the cylinder head.

  1. Apply MP grease to a new oil seal lip.



    A078736E08
  1. Install the oil seal to the camshaft.

    NOTICE:
    1. Do not turn over the oil seal lip.
    2. Insert the oil seal until it stops.

  1. Remove any old packing material from the contact surface.



    A078737E01
  1. Apply seal packing to the No. 1 bearing cap as shown in the illustration.

    Seal packing:
    Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent

    NOTICE:
    1. Install the No. 1 bearing cap within 5 minutes after applying seal packing.
    2. Do not expose the seal to engine oil within 2 hours after installing.



    A005283E01
  1. Install the 5 bearing caps in their proper locations.

  1. Apply a light coat of engine oil to the threads of the bearing cap bolts.



    A078738E01
  1. Using several steps, tighten the 10 bearing cap bolts uniformly in the sequence shown in the illustration.

    Torque:
    16 N*m{ 163 kgf*cm , 12 ft.*lbf }



4. INSTALL CAMSHAFT

NOTICE:
Since the thrust clearance of the camshaft is small, the camshaft must be kept level while it is being installed. If the camshaft is not kept level, damage to the cylinder head or to the camshaft may result. To avoid this, the following steps should be carried out.

  1. Apply new engine oil to the thrust portion and journal of the camshaft.



    A078739E01
  1. Align the timing marks (2-dot mark) of the camshaft drive gear with the mark on the driven gear.

  1. Place the camshaft on the cylinder head.



    A005204E01
  1. Install the 5 bearing caps in their proper locations.

  1. Apply a light coat of engine oil to the threads of the bearing cap bolts.



    A078740E01
  1. Using several steps, tighten the 10 bearing cap bolts uniformly in the sequence shown in the illustration.

    Torque:
    16 N*m{ 163 kgf*cm , 12 ft.*lbf }

  1. Remove the service bolt.



5. INSTALL NO. 3 TIMING BELT COVER
  1. Visually check for cracks and breaks on the gasket of the timing belt cover.

    HINT:
    If a trace of water is found in the visual check, repair it with seal packing when the crack length is within 20 to 30 mm (0.79 to 1.18 in.). Replace the gasket when the crack length is 30 to 40 mm (1.18 to 1.57 in.) and more.



    A180235E01
  1. If the timing belt cover gasket is needed to repair, follow the procedure below.

    1. Repair the cracks and breaks by applying the seal packing to the damaged area.

      Seal packing:
      Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent

      NOTICE:
      When applying the seal packing, apply it as wide and high as possible to fill the surface area of the gasket.



  1. If the timing belt cover gasket is needed to replace, follow the procedure below.

    1. Using a screwdriver and gasket scraper, remove the remaining gasket.

      NOTICE:
      Do not damage the timing belt cover.



    2. A078749E08
    3. Remove the backing paper from a new gasket, and affix the gasket along the groove of the timing belt cover as shown in the illustration.

      NOTICE:
      1. Affix the gasket in the center of the groove.
      2. At the corners, try to keep the gasket thickness uniform.

      HINT:
      Gasket length
      Gasket
      D
      E
      F
      G
      Length
      335 mm
      (13.19 in.)
      180 mm
      (7.09 in.)
      133 mm
      (5.24 in.)
      72 mm
      (2.83 in.)

    4. If there is a gap on the joint of the gasket, apply seal packing to close the gap.

      Seal packing:
      Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent

      NOTICE:
      When applying the seal packing, apply it as wide and high as possible to fill the surface area of the gasket.



    A108157E01
  1. Install the timing belt cover No. 3 with the 6 bolts.

    Torque:
    9.0 N*m{ 92 kgf*cm , 80 in.*lbf }



6. INSTALL CAMSHAFT TIMING PULLEY


    A078750E01
  1. Paying attention to the direction of the belt guide, install the camshaft timing pulley and tighten the bolt temporarily.

    HINT:
    1. Face the belt guide of the RH timing pulley toward the front of the engine.
    2. Face the belt guide of the LH timing pulley toward the rear of the engine.



    A108162E04
  1. Using SST, tighten the RH pulley bolt.

    SST
    09960-10010   (09962-01000, 09963-01000)
    09961-00950  

    Torque:
    125 N*m{ 1275 kgf*cm , 92 ft.*lbf } for use without SST
    90 N*m{ 913 kgf*cm , 66 ft.*lbf } for use with SST

    HINT:
    1. Use a torque wrench with a fulcrum length of 380 mm (14.96 in.).
    2. Make sure that SST and the wrench are connected in a straight line.



    A108164E03
  1. Using SST, tighten the LH pulley bolt.

    SST
    09960-10010   (09962-01000, 09963-01000)

    Torque:
    125 N*m{ 1275 kgf*cm , 92 ft.*lbf }



7. INSTALL NO. 2 TIMING BELT IDLER SUB-ASSEMBLY
  1. Install the No. 2 timing belt idler sub-assembly with the bolt.

    Torque:
    43 N*m{ 438 kgf*cm , 32 ft.*lbf }



8. INSPECT TIMING BELT

NOTICE:
  1. Do not bend, twist or turn the timing belt inside out.
  2. Do not allow the timing belt to come into contact with oil, water or steam.
  3. Do not utilize timing belt tension when installing or removing the mounting bolt of the camshaft timing pulley.
Check the belt for any defects, as shown in the illustration. Also, check the points below.



    EM03336E01
  1. If there is premature parting:

    1. Check for proper installation.

  1. If the belt teeth are cracked or damaged, check if either camshaft is locked.

  1. If there is noticeable wear or cracks on the belt face, check if there are nicks on the side of the idler pulley lock and water pump.

  1. If there is wear or damage to only one side of the belt, check the belt guide and the alignment of each pulley.

  1. If there is noticeable wear on the belt teeth:

    1. Check the timing cover for damage.
    2. Check for foreign objects on the pulley teeth. If there is any trouble in the belt condition, replace the timing belt.



9. INSTALL TIMING BELT
  1. Remove any oil or water on the pulleys, and keep them clean.

    NOTICE:
    1. If there is a trace of water and/or oil on the timing belt, repair the leakage and install a new timing belt.
    2. Wipe only the pulleys. Do not use any cleaning agent.

  1. Inspect the idler pulleys.

    1. Check that the idler pulley turns smoothly.

    2. Visually check the seal portion of the idler pulley for oil leakage.

  1. Inspect the water pump.

    1. Turn the pulley, and check that the water pump bearing moves smoothly and does not make any noise.

    2. Visually check the drain hole for coolant leakage.

  1. Temporarily install the crankshaft pulley bolt and washer to the crankshaft.



    A082349E11
  1. Turn the crankshaft counterclockwise by approximately 60°.

    NOTICE:
    To prevent contacting the piston head and the valve head, set the crankshaft pulley at 60° BTDC/compression position.



    A078751E08
  1. Using SST, turn the timing pulleys, and align the timing marks of the timing pulleys with the No. 3 timing belt cover.

    SST
    09960-10010   (09962-01000, 09963-01000)

    NOTICE:
    Be sure to hold SST with the timing marks aligned to prevent the left bank pulley from deviating to the right.



    A005062E01
  1. Turn the crankshaft, and align the timing mark of the crankshaft timing pulley with the oil pump body.



    A052840E01
  1. Face the front mark on the timing belt forward.

  1. Align the installation mark on the timing belt with the timing mark of the crankshaft timing pulley.

  1. Align the installation marks on the timing belt with the timing marks of the camshaft timing pulleys.



    A078702E02
  1. Install the timing belt in the following order.
    1st
    Crankshaft timing pulley
    2nd
    Water pump pulley
    3rd
    LH camshaft timing pulley
    4th
    No. 2 idler pulley
    5th
    RH camshaft timing pulley
    6th
    No. 1 idler pulley

    NOTICE:
    Be sure to hold SST with the timing marks aligned to prevent the left bank pulley from deviating to the right.



10. INSTALL NO. 1 CHAIN TENSIONER ASSEMBLY
  1. Set the timing belt tensioner upright on the press.



    A036238E01
  1. Slowly press in the push rod.

    NOTICE:
    Do not apply pressure more than 9.8 kN (1000 kgf, 2205 lbf) to the rod.

  1. Align the holes of the push rod and housing, and pass a 1.5 mm hexagon wrench through the holes to keep the setting position of the push rod.

  1. Release the press.

  1. Install the tensioner with the 2 bolts. Alternately tighten the 2 bolts.

    Torque:
    27 N*m{ 280 kgf*cm , 20 ft.*lbf }

    NOTICE:
    Be sure to tighten the bolts equally. Installing the tensioner at an angle may cause improper operation.

  1. Remove the 1.5 mm hexagon wrench from the tensioner.



    A078326E01
  1. Turn the crankshaft 2 revolutions slowly and align the timing mark of the crankshaft timing pulley with the oil pump body.

    NOTICE:
    Always turn the crankshaft clockwise.



    A005052E01
  1. Check the timing marks of the RH and LH timing pulleys are aligned with the timing marks of the No. 3 timing belt cover as shown in the illustration.
    If the marks do not align, remove the timing belt and reinstall it.

  1. Remove the crankshaft pulley bolt.



11. INSTALL NO. 2 TIMING BELT GUIDE


    A036239E01
  1. Install the timing belt guide with the cup side facing toward the engine front.



12. INSTALL ENGINE MOUNTING BRACKET RH


    A108728
  1. Install the engine mounting bracket RH with the 2 bolts and 2 nuts.

    Torque:
    28 N*m{ 286 kgf*cm , 21 ft.*lbf }



13. INSTALL NO. 2 TIMING BELT COVER
  1. Visually check for cracks and breaks on the gasket of the timing belt cover.
    If a trace of water is found in the visual check, replace the timing belt cover.



    A108158E01
  1. Install the timing belt cover with the 5 bolts.

    Torque:
    8.5 N*m{ 87 kgf*cm , 75 in.*lbf }

  1. Connect the 2 clamps.



14. INSTALL NO. 1 TIMING BELT COVER
  1. Visually check for cracks and breaks on the gasket of the timing belt cover.
    If a trace of water is found in the visual check, replace the timing belt cover.

  1. Install the timing belt cover with the 4 bolts.

    Torque:
    8.5 N*m{ 87 kgf*cm , 75 in.*lbf }



15. INSTALL CRANKSHAFT PULLEY


    A108137E01
  1. Align the keyway of the pulley with the key located on the crankshaft and slide the pulley into place.

  1. Using SST, install the pulley bolt.

    SST
    09213-54015   (91651-60855)
    09330-00021  

    Torque:
    220 N*m{ 2243 kgf*cm , 162 ft.*lbf }



16. INSTALL NO. 2 ENGINE MOUNTING STAY


    A108727
  1. Install the No. 2 engine mounting stay and the No. 2 engine mounting bracket with the bolt.

    Torque:
    64 N*m{ 653 kgf*cm , 47 ft.*lbf }



17. INSTALL ENGINE MOVING CONTROL ROD


    A181832E01
  1. Temporarily install the engine moving control rod and bracket with the 4 bolts.

  1. First tighten bolt A, bolt B, then bolt C in this order.

    Torque:
    64 N*m{ 653 kgf*cm , 47 ft.*lbf }

  1. Tighten bolt D.

    Torque:
    23 N*m{ 235 kgf*cm , 17 ft.*lbf }



18. INSTALL AIR CLEANER BRACKET


    A108129
  1. Install the 2 bolts and air cleaner bracket.

    Torque:
    27 N*m{ 275 kgf*cm , 20 ft.*lbf }



19. INSTALL BRAKE MASTER CYLINDER RESERVOIR SUB-ASSEMBLY


    A175945
  1. Install the 2 nuts and brake master cylinder reservoir.

    Torque:
    19 N*m{ 194 kgf*cm , 14 ft.*lbf }

  1. Connect the connector.



20. INSTALL CYLINDER HEAD COVER SUB-ASSEMBLY
  1. Install a new cylinder head cover gasket to the cylinder head cover sub-assembly.



    A078673E01
  1. Apply seal packing to the cylinder head as shown in the illustration.

    Seal packing:
    Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent

    NOTICE:
    1. Remove any oil from the contact surface.
    2. Install the cylinder head cover within 3 minutes after applying seal packing.
    3. Do not start the engine within 2 hours after installing.



    A108160
  1. Install the cylinder head cover with the 9 bolts. Tighten the bolts uniformly in several steps.

    Torque:
    12 N*m{ 122 kgf*cm , 9 ft.*lbf }



    A078541
  1. Install the engine wire harness with the 3 nuts and 2 clamps.

    Torque:
    8.4 N*m{ 85 kgf*cm , 74 in.*lbf }



21. INSTALL IGNITION COIL ASSEMBLY


    A170868
  1. Install the 6 ignition coils with the 6 bolts.

    Torque:
    8.0 N*m{ 80 kgf*cm , 71 in.*lbf }



    A170869
  1. Connect the 6 ignition coil connectors.



22. INSTALL INTAKE AIR SURGE TANK
  1. Install a new gasket to the intake air surge tank.



    A109274E04
  1. Using a socket hexagon wrench 8 mm, install the intake air surge tank with the 4 bolts and 2 nuts. Using several steps, tighten the bolts and nuts uniformly in the sequence shown in the illustration.

    Torque:
    28 N*m{ 286 kgf*cm , 21 ft.*lbf }

  1. Connect the ground cable connector.



    A109273E05
  1. Install the No. 2 surge tank stay (A) with the 2 bolts.

    Torque:
    20 N*m{ 199 kgf*cm , 14 ft.*lbf }

  1. Install the No. 1 surge tank stay (B) with the 2 bolts.

    Torque:
    20 N*m{ 199 kgf*cm , 14 ft.*lbf }

  1. Install the No. 1 engine hunger (C) with the 2 bolts.

    Torque:
    20 N*m{ 199 kgf*cm , 14 ft.*lbf }



    A109268
  1. Connect the ventilation hose.



    A106879E02
  1. Connect the fuel vapor feed hose (A).

  1. Connect the No. 3 water by-pass hose (B).

  1. Connect the No. 2 water by-pass hose (C).

  1. Connect the throttle motor connector (D).



23. INSTALL EMISSION CONTROL VALVE SET


    A109272E02
  1. Install the emission control valve set with the 2 nuts (A).

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }

  1. Connect the No. 2 fuel vapor feed hose (B).

  1. Connect the No. 1 fuel vapor feed hose (C).

  1. Connect the wire harness clamp (D).

  1. Connect the VSV connector (E).



24. INSTALL AIR CLEANER CASE SUB-ASSEMBLY


    A173493
  1. Align the tab on the throttle body with the groove on the air cleaner hose and tighten the hose clamp.



    A173492
  1. Install the air cleaner case sub-assembly with the 5 bolts.

    Torque:
    5.0 N*m{ 51 kgf*cm , 44 in.*lbf }



    A173491
  1. Connect the intake air flow meter connector.

  1. Connect the 2 wire harness clamps to the air cleaner case.



    A173490
  1. Connect the No. 1 ventilation hose.



25. INSTALL AIR CLEANER CAP SUB-ASSEMBLY
  1. Install the air cleaner filter element to the air cleaner case.



    A175875
  1. Install the 2 bolts, 4 clamps and air cleaner cap sub-assembly.

    Torque:
    7.0 N*m{ 71 kgf*cm , 62 in.*lbf }



26. INSTALL BATTERY CARRIER SUB-ASSEMBLY


    A177162
  1. Install the 5 bolts and battery carrier.

    Torque:
    19 N*m{ 194 kgf*cm , 14 ft.*lbf }



27. INSTALL BATTERY
  1. Install the battery clamp and battery.

    Torque:
    5.4 N*m{ 55 kgf*cm , 48 in.*lbf }

  1. Connect the cable to the battery terminal.

    Torque:
    6.4 N*m{ 65 kgf*cm , 56 in.*lbf }

    NOTICE:
    When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).



28. INSTALL FRONT FENDER APRON SEAL RH


    A108741
  1. Install the fender apron seal RH with the 2 bolts and clip.



29. INSTALL FRONT FENDER LINER RH


    A109418
  1. Install the front fender liner with the screw and clip.



30. INSTALL NO. 1 ENGINE UNDER COVER
  1. Install the 6 bolts, 2 screws, 2 clips and No. 1 engine under cover.



31. INSTALL FRONT WHEEL RH


32. ADD ENGINE OIL
  1. Add new oil.

    Engine oil:
    Oil Grade
    Oil Viscosity (SAE)
    ILSAC multigrade engine oil
    1. 5W-20
    2. 0W-20

    Specification:
    Item
    Capacity
    Drain and refill
    with oil filter change
    4.7 liters (5.0 US qts, 4.1 lmp. qts)
    Drain and refill
    without oil filter change
    4.5 liters (4.8 US qts, 4.0 lmp. qts)
    Dry fill
    5.5 liters (5.8 US qts, 4.8 lmp. qts)



33. ADD COOLANT (for Engine)
  1. Tighten the radiator drain cock plug.

  1. Tighten the cylinder block drain cock plugs.

    Torque:
    13 N*m{ 133 kgf*cm , 9 ft.*lbf }

  1. Loosen the air drain plug.



    A176032E01
  1. Install a vinyl tube to the vent tube located on the air drain plug.

  1. Fill the radiator with engine coolant until the vinyl tube is filled with the coolant.

  1. Tighten the air drain plug.

    Torque:
    1.5 N*m{ 15 kgf*cm , 13 in.*lbf }

    CAUTION:
    1. Do not use an alcohol type coolant or plain water alone.
    2. The coolant must be mixed with plain water (preferably demineralized water).


    Coolant capacity:

    Condition
    Capacity
    w/ rear heater
    12.8 liters (13.5 US qts, 11.2 lmp.qts)
    w/o rear heater
    10.6 liters (11.2 US qts, 9.3 lmp.qts)

    HINT:
    1. Improper coolants may damage the engine cooling system.
    2. TOYOTA vehicles are filled with TOYOTA SLLC at the factory. In order to avoid damage to the engine cooling system and other technical problems, only use TOYOTA SLLC or similar high quality ethylene glycol based non-silicate, non-amine, non-nitrite, non-borate coolant with long-life hybrid organic acid technology (coolant with long-life hybrid organic acid technology consists of a combination of low phosphates and organic acids).
    3. Use of coolant which includes more than 50% (freezing protection down to -35°C (-31°F)) or 60% (freezing protection down to -50°C (-58°F)) of ethylene-glycol is recommended but not more than 70%.
    4. Observe the coolant level inside the radiator by pressing the inlet and outlet radiator hoses several times by hand. If the coolant level goes down, add the coolant.

    NOTICE:
    Never use water as a substitute for engine coolant.

  1. Install the radiator cap securely.

  1. Fill the radiator reservoir tank with coolant.

  1. Warm up the engine until the thermostat opens. While the thermostat is open, allow the coolant to circulate for several minutes.

    HINT:
    The thermostat opening timing can be confirmed by squeezing the inlet radiator hose by hand, and sensing vibrations when the engine coolant starts to flow inside the hose.

  1. Stop the engine and wait until the coolant cools down.

  1. Remove the radiator cap and check the coolant level inside the radiator.

  1. If the coolant level is below the full level, perform the steps from (C) through (K) and repeat the operation until the coolant level stays at the full level.

  1. Recheck the coolant level inside the radiator reservoir tank. If it is below the full level, add the coolant.



34. INSPECT FOR COOLANT LEAK (for Engine)

CAUTION:
Do not remove the radiator cap while the engine and radiator are still hot. Pressurized, hot engine coolant and steam may be released and cause serious burns.



    A176028
  1. Fill the radiator with coolant and attach a radiator cap tester.

  1. Pump the tester to 118 kPa (1.2 kgf/cm2, 17.1 psi), then check that the pressure does not drop.
    If the pressure drops, check the hoses, radiator assembly and water pump assembly for leakage. If there are no signs or traces of external engine coolant leakage, check the heater core, cylinder block and cylinder head.



35. INSPECT FOR OIL LEAK


36. INSPECT IGNITION TIMING
  1. Set the vehicle to inspection mode (Click here).

  1. Warm up the engine.

  1. When using the Techstream:

    1. Connect the Techstream to the DLC3.

    2. Enter DATA LIST MODE on the Techstream.

      Ignition timing:
      8 to 12° BTDC

      NOTICE:
      1. Turn all the electrical systems off.
      2. Inspect the engine idle speed with the cooling fan off.

      HINT:
      Refer to the Techstream operator's manual if you need help to select DATA LIST.

    3. Check that the ignition timing advances immediately when the engine speed is increased.



  1. When not using the Techstream:

    1. Using SST, connect terminals 13 (TC) and 4 (CG) of the DLC3.

      SST
      09843-18040  

      NOTICE:
      1. Confirm the terminal numbers before connecting them. Connecting wrong terminals can damage the engine.
      2. Turn off all electrical systems before connecting the terminals.
      3. Perform this inspection after the cooling fan motor is turned off.



    2. A108139
    3. Pull out the red-colored wire harness as shown in the illustration.

    4. Connect the tester terminal of the timing light to the red-colored wire.

      NOTICE:
      Use a timing light which detects the first signal.

    5. Inspect ignition timing at idle.

      Ignition timing:
      8 to 12° BTDC

      NOTICE:
      When checking the ignition timing, the transmission is in neutral.

      HINT:
      Run the engine at 1,000 to 1,300 rpm for 5 seconds, check that the engine rpm returns to idle speed.

    6. Disconnect SST from terminals 13 (TC) and 4 (CG) of the DLC3.

    7. Inspect ignition timing at idle.

      Ignition timing:
      7 to 24° BTDC

    8. Confirm that the ignition timing advances when the engine rpm is increased.

    9. Remove the timing light.



37. INSPECT IDLE SPEED
  1. Set the vehicle to inspection mode (Click here).

  1. Warm up the engine.

  1. Connect the Techstream to the DLC3.

  1. Enter DATA LIST MODE on the Techstream.

    Idle speed:
    850 to 950 rpm.

    NOTICE:
    1. When checking the idle speed, the transmission is in neutral.
    2. Check the idle speed with the cooling fan off.
    3. Switch off all accessories and air conditioning before connecting the Techstream.

    HINT:
    Refer to the Techstream operator's manual for further details.



38. INSTALL NO. 2 ENGINE ROOM SIDE COVER LH


    A173813
  1. Fit the clips and install the No. 2 engine room side cover LH.

    NOTICE:
    1. Be sure to engage the clips securely.
    2. Do not apply excessive force or do not hit the cover to engage the clips. This may cause the cover to break.



39. INSTALL OUTER COWL TOP PANEL SUB-ASSEMBLY


    C175030E01
  1. Install the outer cowl top panel sub-assembly with the 8 bolts and 6 nuts.

    Torque:
    Nut A:
    85 N*m{ 866 kgf*cm , 63 ft.*lbf }
    Bolt B:
    8.8 N*m{ 90 kgf*cm , 78 in.*lbf }
    Nut C:
    8.8 N*m{ 90 kgf*cm , 78 in.*lbf }



    C175029
  1. Engage the 4 clamps.



40. INSTALL WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY


    E150150
  1. Install the windshield wiper motor and link assembly with the 4 bolts.

    Torque:
    7.0 N*m{ 71 kgf*cm , 62 in.*lbf }

  1. Connect the connector.



41. INSTALL COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY


  1. Engage the 20 claws.


    E150149

  1. Install the cowl top ventilator louver sub-assembly with the 2 clips.



    E150146
  1. Engage the 2 claws and connect the front fender to cowl side seal LH.



    E150147
  1. Engage the 2 claws and connect the front fender to cowl side seal RH.



42. INSTALL HOOD TO COWL TOP SEAL


    E150148
  1. Engage the 8 clips and install the hood to cowl top seal.



43. INSTALL FRONT WIPER ARM AND BLADE ASSEMBLY RH
  1. Operate the wiper and stop the windshield wiper motor at the automatic stop position.



  1. When reinstalling:



      E112237E01
    1. Clean the wiper arm serrations.

    2. Clean the wiper pivot serrations with a wire brush.



    E147125E01
  1. Install the front wiper arm and blade assembly RH with the nut to the position shown in the illustration.

    Torque:
    24 N*m{ 245 kgf*cm , 18 ft.*lbf }

    HINT:
    Hold the wiper arm by hand when tightening the nut.

    Area
    Measurement
    A
    25.6 mm (1.00 in.)



44. INSTALL FRONT WIPER ARM AND BLADE ASSEMBLY LH
  1. Operate the wiper and stop the windshield wiper motor at the automatic stop position.



  1. When reinstalling:



      E112237E01
    1. Clean the wiper arm serrations.

    2. Clean the wiper pivot serrations with a wire brush.



    E152618E01
  1. Install the front wiper arm and blade assembly LH with the nut to the position shown in the illustration.

    Torque:
    24 N*m{ 245 kgf*cm , 18 ft.*lbf }

    HINT:
    Hold the wiper arm by hand when tightening the nut.

    Area
    Measurement
    A
    31.9 mm (1.26 in.)

  1. Operate the front wipers while spraying washer fluid onto the windshield glass. Make sure that the front wipers function properly and the wipers do not come into contact with the vehicle body.