Home › ENGINE › 3MZ-FE ENGINE MECHANICAL › CYLINDER HEAD GASKET (for Bank 2)

CYLINDER HEAD GASKET (for Bank 2) > REMOVAL

for Preparation Click here



1. PRECAUTION
  1. Check for DTCs (Click here).

    NOTICE:
    Confirm the P0AA6 (Hybrid Battery Voltage System Isolation Fault) is not output before doing removal or installation work inside the battery. If the DTC is output, perform troubleshooting procedures first.



2. REMOVE FRONT WIPER ARM AND BLADE ASSEMBLY LH


    E150144
  1. Remove the nut, and the front wiper arm and blade assembly LH.



3. REMOVE FRONT WIPER ARM AND BLADE ASSEMBLY RH


    E150145
  1. Remove the nut, and the front wiper arm and blade assembly RH.



4. REMOVE HOOD TO COWL TOP SEAL


    E150148
  1. Disengage the 8 clips and remove the hood to cowl top seal.



5. REMOVE COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY


    E150146
  1. Disengage the 2 claws and disconnect the front fender to cowl side seal LH.



    E150147
  1. Disengage the 2 claws and disconnect the front fender to cowl side seal RH.



  1. Remove the 2 clips.


    E150149

  1. Disengage the 20 claws and remove the cowl top ventilator louver sub-assembly.



6. REMOVE WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY


    E150150
  1. Disconnect the connector.

  1. Remove the 4 bolts, and the windshield wiper motor and link assembly.



7. REMOVE OUTER COWL TOP PANEL SUB-ASSEMBLY


    C175029
  1. Disengage the 4 clamps and separate the wiper wire harness from the outer cowl top panel sub-assembly.



    C175030
  1. Remove the 8 bolts, 6 nuts, and the outer cowl top panel sub-assembly.



8. REMOVE NO. 2 ENGINE ROOM SIDE COVER LH


    A173813
  1. Remove the engine room side cover.



9. REMOVE DISCHARGE FUEL SYSTEM PRESSURE


10. DRAIN COOLANT (for Engine)
  1. Loosen the radiator drain cock plug.

    CAUTION:
    To avoid the danger of being burned, do not remove the radiator cap and drain plugs while the engine and radiator are still hot. Thermal expansion will cause hot engine coolant and steam to blow out from the radiator.

    NOTICE:
    Collect the coolant in a container and dispose of it according to the regulations in your area.

  1. Loosen the cylinder block drain cock plugs.



  1. Remove the radiator cap.


    A176029E01



11. DRAIN ENGINE OIL
  1. Remove the oil filler cap.

  1. Remove the oil drain plug and drain the oil into a container.

  1. Clean and install the oil pan drain plug with a new gasket.

    Torque:
    45 N*m{ 459 kgf*cm , 33 ft.*lbf }



12. REMOVE FRONT WHEEL RH


13. REMOVE NO. 1 ENGINE UNDER COVER
  1. Remove the 6 bolts, 2 screws, 2 clips and No. 1 engine under cover.



14. SEPARATE FRONT FENDER LINER RH


    A109418
  1. Remove the screw and clip, and separate the front fender liner.



15. REMOVE FRONT FENDER APRON SEAL RH


    A108741
  1. Remove the 2 bolts, clip and fender apron seal RH.



16. REMOVE NO. 2 ENGINE UNDER COVER
  1. Remove the 4 bolts and No. 2 engine under cover.



17. REMOVE BATTERY
  1. Disconnect the battery terminal.

    NOTICE:
    When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).

  1. Remove the bolt and battery clamp.

  1. Remove the battery and battery tray.



18. REMOVE BATTERY CARRIER SUB-ASSEMBLY


    A177162
  1. Remove the 5 bolts and battery carrier.



19. REMOVE AIR CLEANER CAP SUB-ASSEMBLY


    A175875
  1. Remove the 2 bolts, 4 clamps and air cleaner cap sub-assembly.

  1. Remove the air cleaner filter element from the air cleaner case.



20. REMOVE AIR CLEANER CASE SUB-ASSEMBLY


    A173490
  1. Separate the No. 1 ventilation hose.



    A173491
  1. Disconnect the intake air flow meter connector.

  1. Disconnect the 2 wire harness clamps from the air cleaner case sub-assembly.



    A173492
  1. Remove the 5 bolts from the air cleaner case sub-assembly.



    A173493
  1. Loosen the hose clamp and separate the No. 1 air cleaner hose.

  1. Remove the air cleaner case sub-assembly.



21. REMOVE SERVICE PLUG GRIP

CAUTION:
  1. Remove the service plug to interrupt a high voltage circuit at the time of the check.
  2. Keep the removed service plug in your pocket to prevent other technicians from accidentally reconnecting it while you are servicing the vehicle.
  3. All the high voltage wiring connectors are colored in orange.



    A175634
  1. Remove the 5 clips and door scuff plate LH.



    A175635
  1. Remove the 2 clips and reclining hinge cover.



    A175636
  1. Wear insulated glove and remove the service plug grip, after sliding up the lever of the service plug grip.

    CAUTION:
    1. Keep the removed service plug in your pocket to prevent other technicians from accidentally reconnecting it while you are servicing the vehicle.
    2. After removing the service plug grip, do not touch the high voltage connectors and terminals for 5 minutes.

    NOTICE:
    After removing the service plug grip, do not operate the power switch as it may damage the hybrid vehicle control ECU.



22. REMOVE INVERTER WITH CONVERTER ASSEMBLY
Click here


23. REMOVE EMISSION CONTROL VALVE SET


    A109272E01
  1. Disconnect the VSV connector (A).

  1. Remove the wire harness clamp (B).

  1. Disconnect the No. 1 fuel vapor feed hose (C).

  1. Disconnect the No. 2 fuel vapor feed hose (D).

  1. Remove the 2 nuts (E), then remove the emission control valve set.



24. REMOVE INTAKE AIR SURGE TANK


    A106879E03
  1. Disconnect the throttle motor connector (A).

  1. Separate the No. 2 water by-pass hose (B).

  1. Separate the No. 3 water by-pass hose (C).

  1. Separate the fuel vapor feed hose (D).



    A109268
  1. Disconnect the ventilation hose.



    A109273E04
  1. Remove the 2 bolts and No. 1 engine hanger (A).

  1. Remove the 2 bolts and No. 1 surge tank stay (B).

  1. Remove the 2 bolts and No. 2 surge tank stay (C).



    A109274E03
  1. Disconnect the ground cable connector.

  1. Using a socket hexagon wrench 8 mm, remove the 4 bolts.

  1. Remove the 2 nuts, then remove the emission control valve bracket and the intake air surge tank.

  1. Remove the gasket from the intake air surge tank.



25. DISCONNECT NO. 1 FUEL PIPE SUB-ASSEMBLY


    A175965
  1. Remove the EFI fuel pipe clamp.



    A175966
  1. Pinch the retainer as illustrated, then pull out the fuel tube connector from the pipe.

    NOTICE:
    1. Remove any dirt and foreign objects on the fuel tube connector before performing this work.
    2. Do not allow any scratches or foreign objects on the parts when disconnecting, as the fuel tube connector has the O-rings that seal the pipe.
    3. Perform this work by hand. Do not use any tools.
    4. Do not forcibly bend, twist or turn the nylon tube.
    5. Protect the disconnected part by covering it with a vinyl bag after disconnecting the fuel tube.
    6. If the fuel tube connector and pipe are stuck, push and pull them to release.



26. DISCONNECT INLET HEATER WATER HOSE


    A079759E01
  1. Lock the hose clamp as shown in the illustration (A).

  1. Disconnect the inlet heater water hose (B).



27. REMOVE INTAKE MANIFOLD


    A108734E01
  1. Remove the nut and disconnect the ground cable (A).

  1. Disconnect the 6 fuel injector connectors.



    A108290E01
  1. In order to remove the intake manifold, using several steps, remove the 9 bolts and 2 nuts in the sequence shown in the illustration.



28. DISCONNECT INLET RADIATOR HOSE


29. REMOVE OUTLET WATER


    A108155E01
  1. Disconnect the ground cable connector (A).

  1. Disconnect the engine coolant temperature sensor connector (B).

  1. Remove the clamp (C).

  1. Remove the 2 bolts, 2 nuts and 2 washers.

  1. Lock the hose clamp as shown in the illustration (D) and remove the water outlet together with No. 1 water by-pass hose (E).

  1. Remove the 2 gaskets from the 2 cylinder heads.



30. SEPARATE BRAKE MASTER CYLINDER RESERVOIR SUB-ASSEMBLY


    A175945
  1. Disconnect the connector.

  1. Remove the 2 nuts and separate the brake master cylinder reservoir.



31. REMOVE AIR CLEANER BRACKET


    A108129
  1. Remove the 2 bolts and air cleaner bracket.



32. REMOVE ENGINE MOVING CONTROL ROD


    A181832
  1. Remove the 4 bolts, the engine moving control rod and the bracket.



33. REMOVE NO. 2 ENGINE MOUNTING STAY


    A108727
  1. Remove the bolt, the No. 2 engine mounting stay and the No. 2 engine mounting bracket.



34. REMOVE CRANKSHAFT PULLEY
  1. Remove the bolt and the timing belt plate.



    A108143E02
  1. Install the pulley bolt to the crankshaft.

  1. Using SST, remove the crankshaft timing pulley.

    SST
    09950-50013   (09951-05010, 09952-05010, 09953-05020, 09954-05011)

    NOTICE:
    1. Do not scratch the sensor part of the crankshaft timing pulley.
    2. Before using SST, apply lubricating oil to the threads and tip of the center bolt 150.



35. REMOVE NO. 1 TIMING BELT COVER
  1. Remove the 4 bolts and the No. 1 timing belt cover.



36. REMOVE NO. 2 TIMING BELT COVER


    A108158E01
  1. Disconnect the engine wire protector clamps from the No. 2 timing belt cover.

  1. Remove the 5 bolts and the timing belt cover.



37. REMOVE ENGINE MOUNTING BRACKET RH


    A108728
  1. Remove the 2 bolts, 2 nuts and engine mounting bracket RH.



38. REMOVE NO. 2 TIMING BELT GUIDE


39. REMOVE TIMING BELT


    A078326E01
  1. Set No. 1 cylinder to TDC/compression.

    1. Temporarily install the crankshaft pulley bolt and washer to the crankshaft.

    2. Turn the crankshaft clockwise, and align the timing mark of the crankshaft timing pulley with the oil pump body.



    3. A005052E01
    4. Check that the timing marks of the camshaft timing pulleys and No. 3 timing belt cover are aligned.
      If not, turn the crankshaft 1 revolution (360°).

    5. Remove the crankshaft pulley bolt.



    A052840E01
  1. If reusing the timing belt, check that there are 4 installation marks on the timing belt as shown in the illustration.

    1. If the installation marks have disappeared, put new installation marks on the timing belt before removing.



    A078327E13
  1. Set No. 1 cylinder to approximately 60° BTDC/compression.

    1. Turn the crankshaft counterclockwise by approximately 60°.

      NOTICE:
      If the timing belt is disengaged, having the crankshaft pulley at a wrong angle can cause the piston head and valve head to come into contact with each other when you remove the camshaft timing pulley and camshaft, causing damage. So always set the crankshaft pulley at the correct angle.



    A078702E01
  1. Remove the 2 bolts and No. 1 chain tensioner.

  1. Remove the timing belt in the following order.
    1st
    No. 1 idler pulley
    2nd
    RH camshaft timing pulley
    3rd
    No. 2 idler pulley
    4th
    LH camshaft timing pulley
    5th
    Water pump pulley
    6th
    Crankshaft timing pulley



40. REMOVE NO. 2 TIMING BELT IDLER SUB-ASSEMBLY
  1. Remove the bolt and No. 2 timing belt idler sub-assembly.



41. REMOVE CAMSHAFT TIMING PULLEY


    A108161E02
  1. Using SST, remove the bolt and the RH timing pulley.

    SST
    09960-10010   (09962-01000, 09963-01000)
    09961-00950  



    A108163E02
  1. Using SST, remove the bolt and the LH timing pulley.

    SST
    09960-10010   (09962-01000, 09963-01000)

    HINT:
    Arrange the camshaft timing pulleys (RH and LH sides) so that they can be returned to the original locations when reassembling.



42. REMOVE NO. 3 TIMING BELT COVER


    A108157E01
  1. Disconnect the 2 engine wire harness clamps from the No. 3 timing belt cover.

  1. Remove the 6 bolts and the timing belt cover.



43. REMOVE FRONT EXHAUST PIPE ASSEMBLY
  1. Disconnect the heated oxygen sensor connector.



    A109430
  1. Remove the 2 bolts, 2 nuts and front exhaust pipe assembly.

  1. Remove the 2 gaskets.



44. REMOVE FRONT NO. 3 EXHAUST PIPE SUB-ASSEMBLY
  1. Disconnect the heated oxygen sensor connector.



    A109431
  1. Remove the 2 bolts, 2 nuts and front No. 3 exhaust pipe sub-assembly.

  1. Remove the 2 gaskets.



45. REMOVE IGNITION COIL ASSEMBLY


    A170869
  1. Disconnect the 6 ignition coil connectors.



    A170868
  1. Remove the 6 bolts and 6 ignition coils.



46. REMOVE NO. 3 MANIFOLD CONVERTER INSULATOR


    A108736
  1. Remove the bolt, nut and No. 3 manifold converter insulator.



47. REMOVE NO. 2 EXHAUST MANIFOLD HEAT INSULATOR


    A108154
  1. Remove the 2 bolts and No. 2 manifold heat insulator.



48. REMOVE NO. 2 EXHAUST MANIFOLD CONVERTER SUB-ASSEMBLY
  1. Disconnect the heated oxygen sensor connector.



    A181833E01
  1. Using several steps, loosen and remove the 6 nuts and bolt in the sequence shown in the illustration.

  1. Remove the No. 2 exhaust manifold converter and the gasket from the cylinder head LH.



49. REMOVE OIL LEVEL DIPSTICK GUIDE


    A108140
  1. Remove the bolt which is used to secure the oil dipstick gauge guide from the cylinder head LH.

  1. Pull out the oil level gauge guide and the oil dipstick gauge together from the cylinder block.

  1. Remove the O-ring from the oil level gauge guide.



50. REMOVE INLET WATER PIPE


    A080823
  1. Remove the bolt and the water inlet pipe.

  1. Remove the O-ring from the water inlet pipe.



51. REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY LH


    A036719E01
  1. Using an E6 "TORX" socket wrench, remove the 2 bolts and disconnect the engine wire harness protector.



    A114812
  1. Remove the 2 engine wire harness clamps.

    CAUTION:
    Wear insulating gloves.



    A108125
  1. Remove the 2 bolts and 2 brackets.



    A108159
  1. Remove the 9 bolts and the cylinder head cover.



52. REMOVE NO. 3 CAMSHAFT SUB-ASSEMBLY

NOTICE:
Since the thrust clearance of the camshaft is small, the camshaft must be kept level while it is being removed. If the camshaft is not kept level, damage to the cylinder head or to the camshaft may result. To avoid this, the following steps should be carried out.



    A078710E08
  1. Align the timing marks (1-dot mark) of the camshaft drive and the driven gears by turning the camshaft with a wrench.



    A180236E01
  1. Secure the exhaust camshaft sub-gear to the main gear with a service bolt.

    Torque:
    5.0 N*m{ 51 kgf*cm , 44 in.*lbf }

    Recommended service bolt: 
    Thread diameter
    6.0 mm (0.24 in.)
    Thread pitch
    1.0 mm (0.04 in.)
    Bolt length
    16 to 20 mm (0.63 to 0.79 in.)

    HINT:
    When removing the camshaft, make certain that the torsional spring force of the sub-gear has been eliminated by installing the service bolt.



    A078712E01
  1. Using several steps, loosen and remove the 10 bearing cap bolts uniformly in the sequence shown in the illustration. Remove the 5 bearing caps and the No. 3 camshaft.

    NOTICE:
    1. Do not pry out the camshaft.
    2. Do not damage the portion of the cylinder head which receives the shaft thrust.



53. REMOVE NO. 4 CAMSHAFT SUB-ASSEMBLY


    A078713E01
  1. Using several steps, loosen and remove the 10 bearing cap bolts uniformly in the sequence shown in the illustration. Remove the 5 bearing caps and the No. 4 camshaft.

    NOTICE:
    1. Do not pry out the camshaft.
    2. Do not damage the portion of the cylinder head which receives the shaft thrust.

  1. Remove the oil seal from the No. 4 camshaft.



54. REMOVE CYLINDER HEAD LH


    A108141E01
  1. Disconnect the VVT sensor connector (A).

  1. Disconnect the camshaft timing oil control valve connector (B).

  1. Remove the 2 nuts and disconnect the ground cable (C).

  1. Remove the 2 bolts, wire harness clamp and No. 2 intake air connector bracket.



    A078718E01
  1. Using an 8 mm socket hexagon wrench, remove the hexagon bolt.



    A078719E01
  1. Using several steps, loosen the 8 cylinder head bolts uniformly in the sequence shown in the illustration. Remove the 8 cylinder head bolts and plate washers.

    NOTICE:
    1. Do not drop the washers into the cylinder head.
    2. Head warpage or cracking could result from removing bolts in an incorrect order.

  1. Remove the cylinder head.



55. REMOVE NO. 2 CYLINDER HEAD GASKET