Home › BODY ELECTRICAL › METER › METER / GAUGE SYSTEM

METER / GAUGE SYSTEM > Fuel Receiver Gauge Malfunction

for Preparation Click here


DESCRIPTION

  1. The meter CPU uses the fuel sender gauge assembly to determine the level of the fuel in the fuel tank. The resistance of the fuel sender gauge will vary between approximately 4 Ω with the float at the full position, and 110 Ω with the float at the empty position. The meter outputs battery voltage through two 220 Ω resistors that are mounted in parallel inside the meter CPU. The meter CPU measures the voltage between the variable resistor in the fuel sender gauge and the two resistors mounted in parallel in the meter. Voltage measured at this point will vary as the float of the fuel sender gauge is moved. The highest voltage observed should be approximately half of the auxiliary battery voltage.

HINT:
The fuel level warning light will come on when the fuel level is below 11.0 liters.


WIRING DIAGRAM


E152381E06


INSPECTION PROCEDURE

1.CHECK CAN COMMUNICATION SYSTEM
  1. Check if a CAN communication DTC is output (Click here).


Result:

Result
Proceed to
CAN communication DTC is not output.
A
CAN communication DTC is output.
B



B
GO TO CAN COMMUNICATION SYSTEM (Click here)
A


2.PERFORM ACTIVE TEST USING TECHSTREAM (FUEL METER OPERATION)
  1. Connect Techstream to the DLC3.

  1. Power switch on (READY).

  1. Turn the tester on.

  1. Enter following menus: Body Electrical / Combination Meter / Active Test.

  1. Check the operation by referring to the table below.

    Combination Meter: 
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Fuel Meter Operation
    Fuel receiver gauge
    EMPTY, 1/2, FULL
    -

    OK:
    Fuel receiver gauge indication is normal.



NG
REPLACE COMBINATION METER ASSEMBLY (Click here)
OK


3.READ VALUE USING TECHSTREAM (FUEL INPUT)
  1. Connect Techstream to the DLC3.

  1. Power switch on (READY).

  1. Turn the tester on.

  1. Enter following menus: Body Electrical / Combination Meter / Data List.

  1. Check the values by referring to the table below.

    Combination Meter: 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Fuel Input
    Fuel input signal Min.: 0, Max.: 127.5
    Fuel gauge indicates (E): 6.8 (L)
    Fuel gauge indicates (1/2): 32.4 (L)
    Fuel gauge indicates (F): 58.3 (L)
    -

    OK:
    Fuel value signal displayed on the tester is almost the same as needle indication.



NG
REPLACE COMBINATION METER ASSEMBLY (Click here)
OK


4.CHECK HARNESS AND CONNECTOR (COMBINATION METER - FUEL SENDER GAUGE ASSEMBLY)


    E152442E04
  1. Disconnect the E1 and fuel sender gauge assembly connectors.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    E1-34 (FR) - 2
    Always
    Below 1 Ω
    E1-19 (FE) - 1
    Always
    Below 1 Ω
    2 - Body ground
    Always
    10 kΩ or higher
    E1-34 (FR) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


5.INSPECT FUEL SENDER GAUGE ASSEMBLY


    E146925E01
  1. Disconnect the fuel sender gauge connector.

  1. Measure the resistance between the terminals 1 and 2 of the connector according to the value(s) in the table below.

    Standard resistance:
    Float Level
    Resistance (Ω)
    F
    3.0 to 5.0
    Between E and F
    3.0 to 111.0 (Gradually changes)
    E
    109.0 to 111.0

  1. Remove the fuel sender gauge assembly .

  1. Check that the float moves smoothly between F and E.

  1. Check the fuel sender gauge if there is deformation in the arm.



NG
REPLACE FUEL SENDER GAUGE ASSEMBLY
OK


6.REPLACE COMBINATION METER ASSEMBLY
  1. Replace the combination meter assembly with a new one or a normal one .

    OK:
    The operation of the combination meter assembly returns to normal.



NG
REPLACE HYBRID VEHICLE CONTROL ECU (for 3MZ-FE)
OK

END