Home › HYBRID SYSTEM · P310 › HYBRID VEHICLE CONTROL › HYBRID CONTROL SYSTEM

DTC    P2601-777    Coolant Pump Control Circuit Range / Performance

for Preparation Click here


DESCRIPTION

HINT:
Although the DTC title refers to "coolant pump", this DTC is related to the oil pump control circuit.
The hybrid vehicle control ECU detects the MG1 and MG2 temperature based on signals from the generator and motor temperature sensors and activates the OIL PMP relay and oil pump driver (oil pump with motor assembly).
The hybrid vehicle control ECU monitors OPST signals from the oil pump driver and detects malfunctions.


DTC No.
INF No.
DTC Detection Condition
Trouble Area
P2601
777
Command signal (OPM1) from hybrid vehicle control ECU is abnormal
  1. Wire harness or connector
  2. Oil pump with motor assembly
  3. Hybrid vehicle control ECU
The oil pump with motor assembly is activated when:
  1. MG1 temperature is 248°F (120°C) or more
  2. MG2 temperature is 266°F (130°C) or more and the MG1 temperature is 212°F (100°C) or more

HINT:
  1. If the second condition occurs, and the oil pump with motor assembly does not activate even though the MG1 temperature is 212°F (100°C) or more, the hybrid vehicle control ECU will attempt to activate it when the MG1 temperature changes to 230°F (110°C), 248°F (120°C), 266°F (130°C), 284°F (140°C) and 302°F (150°C) respectively.
  2. The oil pump cannot be activated only with the OIL PMP relay on. It is activated after receiving the command signals (OPM1) from the hybrid vehicle control ECU.


WIRING DIAGRAM


A178013E03


INSPECTION PROCEDURE

NOTICE:
  1. When troubleshooting the oil pump with motor assembly, check for the following conditions:
    1. ATF temperature inside the oil cooler is 41°F (5°C) or more.
    2. The ambient temperature sensor value is 41°F (5°C) or more.

1.CHECK OPERATION OF OIL PUMP WITH MOTOR ASSEMBLY
  1. Connect the Techstream to the DLC3.

  1. Turn the power switch on (IG).

  1. Select the following menu items: Powertrain / Hybrid Control / Active Test / Inspection Mode -2WD Inspection.

  1. Turn the power switch on (READY).



    A175140E02
  1. Connect an oscilloscope between the hybrid vehicle control ECU terminals specified in the following table, and measure the waveform.
    Item
    Contents
    Terminal
    A43-6 (OPM1) - B3-5 (E1)
    Equipment Setting
    5 V/DIV, 5 ms./DIV.
    Condition
    Power switch on (READY)

    Result:
    Waveform
    Proceed to
    Normal waveform
    A
    Waveform other than normal waveform
    B
    No waveform (0 V)
    C
    No waveform (12 V)
    D



B
REPLACE HYBRID VEHICLE CONTROL ECU (Click here)

C
Go to step 2

D
Go to step 4
A

REPLACE OIL PUMP WITH MOTOR ASSEMBLY (Click here)  

2.CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU - OIL PUMP WITH MOTOR ASSEMBLY)
  1. Turn the power switch off.

  1. Disconnect the oil pump with motor assembly connector.

  1. Disconnect connector A43 from the hybrid vehicle control ECU.



    A175141E08
  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance (Check for open):
    Tester Connection
    Switch Condition
    Specified Condition
    A43-6 (OPM1) - A48-3 (OPM1)
    Power switch off
    Below 1 Ω

    Standard resistance (Check for short):
    Tester Connection
    Switch Condition
    Specified Condition
    A43-6 (OPM1) or A48-3 (OPM1) - Body ground and other terminals
    Power switch off
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3.CHECK HYBRID VEHICLE CONTROL ECU (OPM1 TERMINAL RESISTANCE CHECK)
  1. Connect the oil pump with motor assembly connector.

  1. Disconnect connector B3 from the hybrid vehicle control ECU.



    A175142E03
  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance :
    Tester Connection
    Switch Condition
    Specified Condition
    A43-6 (OPM1) - B3-5 (E1)
    Power switch off
    10 kΩ or higher



NG
REPLACE OIL PUMP WITH MOTOR ASSEMBLY (Click here)
OK

REPLACE HYBRID VEHICLE CONTROL ECU (Click here)  

4.CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU - OIL PUMP WITH MOTOR ASSEMBLY)
  1. Turn the power switch off.

  1. Disconnect the oil pump with motor assembly connector.

  1. Disconnect connector A43 from the hybrid vehicle control ECU.

  1. Turn the power switch on (IG).



    A175141E09
  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    A43-6 (OPM1) - Body ground
    Power switch on (IG)
    Below 1 V

    NOTICE:
    Turning the power switch on (IG) with the oil pump with motor assembly connector and hybrid vehicle control ECU connector disconnected causes other DTCs to be stored. Clear the DTCs after performing this inspection.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


5.CHECK OIL PUMP WITH MOTOR ASSEMBLY
  1. Turn the power switch off.



    A175143E04
  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance :
    Tester Connection
    Switch Condition
    Specified Condition
    A48-4 (L) - A48-3 (OPM1)
    Power switch off
    10 kΩ or higher



NG
REPLACE OIL PUMP WITH MOTOR ASSEMBLY (Click here)
OK

REPLACE HYBRID VEHICLE CONTROL ECU (Click here)