Home › RESTRAINTS › SUPPLEMENTAL RESTRAINT SYSTEM › AIRBAG SYSTEM

DTC    B1650/32    Occupant Classification System Malfunction

for Preparation Click here


DESCRIPTION

The occupant classification system circuit consists of the center airbag sensor assembly and the occupant classification system.
If the center airbag sensor assembly receives signals from the occupant classification ECU, it determines whether the front passenger airbag assembly, the front seat side airbag assembly RH and front seat outer belt assembly RH should be operated.
DTC B1650/32 is recorded when a malfunction is detected in the occupant classification system circuit.

DTC No.
DTC Detection Condition
Trouble Area
B1650/32
  1. The center airbag sensor assembly receives a line short circuit signal, an open circuit signal, a short circuit to ground signal or a short circuit to B+ signal in the occupant classification system circuit for 2 seconds.
  2. Occupant classification system malfunction
  3. Center airbag sensor assembly malfunction
  1. Floor wire
  2. Front seat wire RH
  3. Occupant classification system
  4. Center airbag sensor assembly

WIRING DIAGRAM


C167958E02


INSPECTION PROCEDURE

1.CHECK DTC (OCCUPANT CLASSIFICATION ECU)
  1. Turn the power switch on (IG).

  1. Using Techstream, check the DTCs of the occupant classification ECU (Click here).



NG
REPAIR CIRCUITS INDICATED BY OUTPUT DTCS (Click here)
OK


2.CHECK CONNECTORS
  1. Turn the power switch off.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Check that the connectors are properly connected to the center airbag sensor assembly and the occupant classification ECU. Also check that the connectors that link the front seat wire RH and floor wire are properly connected.

    OK:
    The connectors are properly connected.

    HINT:
    If the connectors are not connected securely, reconnect the connectors and proceed to the next inspection.

  1. Disconnect the connectors from the center airbag sensor assembly and the occupant classification ECU. Also disconnect the connectors that link the front seat wire RH and floor wire.

  1. Check that the terminals of the connectors are not damaged.

    OK:
    The terminals are not deformed or damaged.



NG
REPLACE WIRE HARNESS
OK


3.CHECK OCCUPANT CLASSIFICATION SYSTEM CIRCUIT (OPEN)


  1. Using SST, connect terminals 16 (FSP+) and 24 (FSP-) of connector B.


    C169179E03

    NOTICE:
    Do not forcibly insert SST into the terminals of the connector when connecting the wire.

SST
09843-18040  
  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    a3-8 (FSR+) - a3-4 (FSR-)
    Always
    Below 1 Ω



NG
Go to step 7
OK


4.CHECK OCCUPANT CLASSIFICATION SYSTEM CIRCUIT (SHORT)


    C169187E02
  1. Disconnect SST from connector B.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    a3-8 (FSR+) - a3-4 (FSR-)
    Always
    1 MΩ or higher



NG
Go to step 8
OK


5.CHECK OCCUPANT CLASSIFICATION SYSTEM CIRCUIT (SHORT TO B+)


    C169187E02
  1. Connect the negative (-) terminal cable to the battery.

  1. Turn the power switch on (IG).

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    a3-8 (FSR+) - Body ground
    power switch on (IG)
    Below 1 V
    a3-4 (FSR-) - Body ground
    power switch on (IG)
    Below 1 V



NG
Go to step 9
OK


6.CHECK OCCUPANT CLASSIFICATION SYSTEM CIRCUIT (SHORT TO GROUND)


    C169187E02
  1. Turn the power switch off.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    a3-8 (FSR+) - Body ground
    Always
    1 MΩ or higher
    a3-4 (FSR-) - Body ground
    Always
    1 MΩ or higher

    HINT:
    After replacing the center airbag sensor assembly, check for DTCs of the center airbag sensor assembly. If the DTC B1650/32 is detected, replace the occupant classification ECU (Click here) and perform "zero point calibration" and "sensitivity check" of the occupant classification system (Click here).



NG
Go to step 10
OK

REPLACE CENTER AIRBAG SENSOR ASSEMBLY (Click here)  

7.CHECK FLOOR WIRE (OPEN)


  1. Disconnect the front seat wire RH connector from the floor wire.


    C169181E03

    HINT:
    SST has already been inserted into connector B.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    Na1-1 (FSR+) - Na1-4 (FSR-)
    Always
    Below 1 Ω



NG
REPLACE FLOOR WIRE
OK

REPLACE FRONT SEAT WIRE RH 

8.CHECK FLOOR WIRE (SHORT)


    C169180E03
  1. Disconnect the front seat wire RH connector from the floor wire.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    Na1-1 (FSR+) - Na1-4 (FSR-)
    Always
    1 MΩ or higher



NG
REPLACE FLOOR WIRE
OK

REPLACE FRONT SEAT WIRE RH 

9.CHECK FLOOR WIRE (SHORT TO B+)


    C169180E03
  1. Turn the power switch off.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Disconnect the front seat wire RH connector from the floor wire.

  1. Connect the negative (-) terminal cable to the battery.

  1. Turn the power switch on (IG).

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    Na1-1 (FSR+) - Body ground
    power switch on (IG)
    Below 1 V
    Na1-4 (FSR-) - Body ground
    power switch on (IG)
    Below 1 V



NG
REPLACE FLOOR WIRE
OK

REPLACE FRONT SEAT WIRE RH 

10.CHECK FLOOR WIRE (SHORT TO GROUND)


    C169180E03
  1. Disconnect the front seat wire RH connector from the floor wire.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    Na1-1 (FSR+) - Body ground
    Always
    1 MΩ or higher
    Na1-4 (FSR-) - Body ground
    Always
    1 MΩ or higher



NG
REPLACE FLOOR WIRE
OK

REPLACE FRONT SEAT WIRE RH