Home › HYBRID SYSTEM · P310 › HYBRID BATTERY CONTROL › HYBRID BATTERY SYSTEM

DTC    P0A9C-123    Hybrid Battery Temperature Sensor "A"

DTC    P0AC5-123    Hybrid Battery Temperature Sensor "B" Circuit

DTC    P0ACA-123    Hybrid Battery Temperature Sensor "C" Circuit

for Preparation Click here


DESCRIPTION

The battery temperature sensors are provided at 8 locations on the bottom of the HV battery. The resistance of the thermistor, which is built into each battery temperature sensor, varies in accordance with changes in the HV battery temperature. The lower the battery temperature, the higher the thermistor resistance. Conversely, the higher the temperature, the lower the resistance. The battery smart unit uses the battery temperature sensor to detect the HV battery temperature, and sends the detected value to the hybrid vehicle control ECU. Based on the results of this detection, the hybrid vehicle control ECU controls the blower fan. (The blower fan starts when HV battery temperature rises above a predetermined level.)

A171806E02


A108795E02


DTC No.
DTC Detection Condition
Trouble Area
P0A9C-123
P0AC5-123
P0ACA-123
  1. When the battery temperature sensor performance is abnormal (1 trip detection/2 trip detection)
  1. HV battery assembly
  2. Battery smart unit

HINT:
After confirming that a DTC is output, use the Techstream to check "Temp of BATT TB 1 to 8" in the hybrid vehicle control system ECU data list.


Temperature Displayed
Malfunction
Below -49°F (-45°C)
Open or +B short circuit
203°F (95°C) or more
GND short circuit

MONITOR DESCRIPTION

If the temperature indicated by the battery temperature sensor is lower than the standard level (open circuit), or is higher than the standard level (short circuit), the battery smart unit interprets this as a sensor malfunction. If the battery smart unit detects that HV battery temperature is out of a normal range, the hybrid vehicle control ECU illuminates the MIL and sets a DTC.

MONITOR STRATEGY


Related DTCs
P0A9C-123/P0AC5-123/P0ACA-123
Required sensors/components
Battery temperature sensor
Frequency of operation
Continuous
Duration
TOYOTA's intellectual property
MIL operation
Immediately or 2 driving cycles
Sequence of operation
None

TYPICAL ENABLING CONDITIONS


The monitor will run whenever the DTCs listed are not present
TOYOTA's intellectual property

TYPICAL MALFUNCTION THRESHOLDS


TOYOTA's intellectual property
-

COMPONENT OPERATING RANGE


Battery temperature sensor
9 to 11 kΩ at 77°F (25°C)

WIRING DIAGRAM


A176193E01


INSPECTION PROCEDURE

CAUTION:
  1. Before inspecting the high-voltage system, take safety precautions to prevent electrical shocks, such as wearing insulated gloves and removing the service plug grip. After removing the service plug grip, put it in your pocket to prevent other technicians from accidentally reconnecting it while you are working on the high-voltage system.
  2. After disconnecting the service plug grip, wait for at least 5 minutes before touching any of the high-voltage connectors or terminals.

HINT:
At least 5 minutes is required to discharge the high-voltage capacitor inside the inverter with converter assembly.

1.CHECK DTC OUTPUT (DTC P0A1F IS OUTPUT)
  1. Connect the Techstream to the DLC3.

  1. Turn the power switch on (IG).

  1. Select the following menu items: Powertrain / Hybrid Control / Trouble Codes.

  1. Read output DTCs (Click here).

    Result:
    Result
    Proceed to
    P0A1F-123 is not output.
    A
    P0A1F-123 is also output.
    B



B
GO TO DTC CHART (P0A1F-123) (Click here)
A


2.CHECK HV BATTERY (BATTERY TEMPERATURE SENSOR)

CAUTION:
Be sure to wear insulated gloves and protective goggles.



    A173713E01
  1. Disconnect the z33 and z34 connectors from the battery smart unit (Click here).

  1. Measure the resistance according to the conditions and value(s) in the tables below.
    Tester Connection
    Thermistor No.
    z33-1(TB0) - z33-6(GB0)
    0
    z33-2(TB1) - z33-7(GB1)
    1
    z34-1(TB2) - z34-4(GB2)
    2
    z34-2(TB3) - z34-5(GB3)
    3
    z34-3(TB4) - z34-6(GB4)
    4
    z33-3(TB5) - z33-8(GB5)
    5
    z33-4(TB6) - z33-9(GB6)
    6
    z33-5(TB7) - z33-10(GB7)
    7

    Standard resistance:
    Thermistor Temperature
    Switch Condition
    Specified Condition (kΩ)
    32°F (0°C)
    Power switch off
    27.0 to 27.6
    77°F (25°C)
    Power switch off
    9.9 to 10.1
    104°F (40°C)
    Power switch off
    5.77 to 5.89



NG
REPLACE HV BATTERY ASSEMBLY (Click here)
OK


3.CHECK INSTALLATION OF BATTERY TEMPERATURE SENSOR

CAUTION:
Be sure to wear insulated gloves and protective goggles.

  1. Remove the HV battery with the relevant battery temperature sensor (Click here).



    A108237E01
  1. Turn over the relevant HV battery and check the installation of the battery temperature sensor.

    Result:
    Result
    Proceed to
    Battery temperature sensor is installed correctly.
    A
    Claws are damaged.
    B
    Battery temperature sensor is not installed correctly, but claws are not damaged.
    C

    HINT:
    Do not leave the HV battery 10 minutes or more after turning the battery over.



B
REPLACE HV BATTERY ASSEMBLY (Click here)

C
INSTALL CORRECTLY
A

REPLACE BATTERY SMART UNIT (Click here)