Home › HYBRID SYSTEM · P310 › HYBRID BATTERY CONTROL › HYBRID BATTERY SYSTEM

DTC    P0AD0-123    Hybrid Battery Pack Cooling Fan 3 Performance or Stuck OFF

for Preparation Click here


DESCRIPTION

  1. Refer to the description for DTC P0A84-123 .

DTC No.
DTC Detection Condition
Trouble Area
P0AD0-123
When the speed of the battery blower assembly is not within the target range speed (1 trip detection)
  1. Wire harness or connector
  2. Hybrid vehicle control ECU
  3. Battery cooling blower assembly
  4. Battery smart unit

WIRING DIAGRAM

  1. Refer to the wiring diagram for DTC P0A84-123 .

INSPECTION PROCEDURE

CAUTION:
  1. Before inspecting the high-voltage system, take safety precautions to prevent electrical shocks, such as wearing insulated gloves and removing the service plug grip. After removing the service plug grip, put it in your pocket to prevent other technicians from accidentally reconnecting it while you are working on the high-voltage system.
  2. After disconnecting the service plug grip, wait for at least 5 minutes before touching any of the high-voltage connectors or terminals.

HINT:
At least 5 minutes is required to discharge the high-voltage capacitor inside the inverter with converter assembly.

1.CHECK DTC OUTPUT (HV)
  1. Connect the Techstream to the DLC3.

  1. Turn the power switch on (IG) and the Techstream on.

  1. Select the following menu items: Powertrain / Hybrid Control / Trouble Codes.

  1. Read output DTCs (Click here).

    Result:

    Result
    Proceed to
    P0AD0-123 only is output
    A
    P0A1F-123 is output
    B
    Any of P0A84-123, P0A85-123, P0A99-123, P0A9A-123, P0AD2-123 and P0AD3-123 are output
    C



B
GO TO DTC CHART (P0A1F-123) (Click here)

C
GO TO DTC CHART
A


2.CHECK BATTERY COOLING BLOWER ASSEMBLY

CAUTION:
Be sure to wear insulated gloves and protective goggles.

  1. Connect the Techstream to the DLC3.

  1. Select the following menu items: Powertrain / Hybrid Control / Data List / VMF Fan Motor Voltage 1 to 3 and Temp of BATT TB 1to 8.

    HINT:
    It is easier to see the change in the VMF Fan Motor Voltage when displayed in the line chart.

  1. Perform a road test and check that there is a malfunction in the VMF Fan Motor Voltage 3 while the battery cooling blower assembly is operating. (*1)

    HINT:
    The fan operates when the battery temperature is approximately 97°F (36°C) or more.



    A173697E02
  1. Remove the battery cover and replace the battery cooling blower assembly with another battery cooling blower assembly (Click here).

  1. Install the battery cover.

  1. Select the following menu items: Powertrain / Hybrid Control / Data List / VMF Fan Motor Voltage 1 to 3 and Temp of BATT TB 1to 8.

    HINT:
    It is easier to see the change in the VMF Fan Motor Voltage when displayed in the line chart.

  1. Perform a road test and check that the malfunction in (*1) is reproduced in another battery cooling blower assembly.

    Result:
    Result
    Proceed to
    The malfunction is reproduced in the same battery cooling blower.
    A
    The malfunction is reproduced in another battery cooling blower.
    B

    HINT:
    The battery cooling blower operates when the battery temperature is approximately 97°F (36°C) or more.



B
REPLACE BATTERY COOLING BLOWER ASSEMBLY (Click here)
A


3.CHECK HARNESS AND CONNECTOR (BATTERY COOLING BLOWER ASSEMBLY - BATTERY SMART UNIT)

CAUTION:
Be sure to wear insulated gloves and protective goggles.

  1. Remove the service plug grip.

  1. Remove the battery cover.



    A173697E07
  1. Disconnect the O47 connector from the battery cooling blower assembly.

  1. Disconnect the z18 connector from the battery smart unit (Click here).



    A173709E03
  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance (Check for open):
    Tester Connection
    Switch Condition
    Specified Condition
    O47-2 (VM2) - z18-5 (VM2)
    Power switch off
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4.CHECK HARNESS AND CONNECTOR (BATTERY COOLING BLOWER ASSEMBLY - HYBRID VEHICLE CONTROL ECU)
  1. Disconnect D36 connector from the hybrid vehicle control ECU (Click here).



    A173711E08
  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance (Check for open):
    Tester Connection
    Switch Condition
    Specified Condition
    O47-3 (Sl2) - D36-13 (Sl2)
    Power switch off
    Below 1 Ω

Standard resistance (Check for short):
Tester Connection
Switch Condition
Specified Condition
O47-3 (Sl2) - O47-4 (GND2)
Power switch off
10 kΩ or more
O47-3 (Sl2) - Body ground
Power switch off
10 kΩ or more



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


5.READ VALUE USING TECHSTREAM (VM2 VOLTAGE)

CAUTION:
Be sure to wear insulated gloves and protective goggles.

  1. Connect the O47, z18 and D36 connector.

  1. Connect the Techstream to the DLC3.

  1. Turn the power switch on (IG) and the Techstream on.

  1. Select the following menu items: Powertrain / Hybrid Control / Active Test / Driving the Battery Cooling Fan.

  1. Select the following menu items: All Data / VMF Fan Motor Voltage 3.

  1. Select each air volume mode (1 to 6) in the "Driving the Battery Cooling Fan" active test to operate the battery cooling blower assembly.



    A183993E12
  1. While the cooling fan is operating, compare the value in the Data List (VMF Fan Motor Voltage 3) with the voltage value that was actually measured at the battery cooling blower assembly connector.

    Specified Condition:
    Tester Connection
    Condition
    Specified Condition
    O47-2 (VM2) - O47-4 (GND2)
    Battery cooling blower is operating
    Difference between the value in the Data List (VMF Fan Motor Voltage 3) and the actual measurement value is 1 V or less.

    HINT:
    1. Compare the values in each air volume mode (1 to 6).
    2. If the power switch is turned on (IG) with the service plug grip removed, DTC P0A0D-350 for the interlock switch system will be stored. If this DTC is output, clear the DTC using the Techstream.



NG
REPLACE BATTERY SMART UNIT (Click here)
OK

REPLACE HYBRID VEHICLE CONTROL ECU (Click here)