Home › HYBRID SYSTEM ยท P310 › HYBRID BATTERY CONTROL › HYBRID BATTERY SYSTEM

DTC    P3011-123    Battery Block 1 Becomes Weak

DTC    P3012-123    Battery Block 2 Becomes Weak

DTC    P3013-123    Battery Block 3 Becomes Weak

DTC    P3014-123    Battery Block 4 Becomes Weak

DTC    P3015-123    Battery Block 5 Becomes Weak

DTC    P3016-123    Battery Block 6 Becomes Weak

DTC    P3017-123    Battery Block 7 Becomes Weak

DTC    P3018-123    Battery Block 8 Becomes Weak

DTC    P3019-123    Battery Block 9 Becomes Weak

DTC    P3020-123    Battery Block 10 Becomes Weak

DTC    P3021-123    Battery Block 11 Becomes Weak

DTC    P3022-123    Battery Block 12 Becomes Weak

DTC    P3023-123    Battery Block 13 Becomes Weak

DTC    P3024-123    Battery Block 14 Becomes Weak

DTC    P3025-123    Battery Block 15 Becomes Weak

for Preparation Click here


DESCRIPTION

  1. Refer to the description for DTC P0A80 .

DTC No.
DTC Detection Condition
Trouble Area
P3011-123
P3012-123
P3013-123
P3014-123
P3015-123
P3016-123
P3017-123
P3018-123
P3019-123
P3020-123
P3021-123
P3022-123
P3023-123
P3024-123
P3025-123
Presence of a malfunctioning block is determined based on each battery block voltage (1 trip detection).
  1. Battery smart unit
  2. HV battery assembly

HINT:
P3011-123 and P3025-123 will not be set unless the vehicle is driven for approximately 10 minutes after clearing the DTCs.


MONITOR DESCRIPTION

If there is an abnormal internal resistance or electromotive voltage in the battery blocks, the battery smart unit determines that a malfunction has occurred. When the malfunction detection condition is satisfied, the hybrid vehicle control ECU illuminates the MIL and sets a DTC.

MONITOR STRATEGY


Related DTCs
P3011 to P3025
Required sensors/components
HV battery
Frequency of operation
Continuous
Duration
TOYOTA's intellectual property
MIL operation
Immediately
Sequence of operation
None

TYPICAL ENABLING CONDITIONS


The monitor will run whenever the DTCs listed are not present
TOYOTA's intellectual property

TYPICAL MALFUNCTION THRESHOLDS


Open circuit voltage deviation
More than 1.2 V

COMPONENT OPERATING RANGE


HV battery
Any DTCs from P3011-123 to P3025-123 are not detected

INSPECTION PROCEDURE

1.CHECK DTC OUTPUT (DTC P0A1F-123 IS OUTPUT)
  1. Connect the Techstream to the DLC3.

  1. Turn the power switch on (IG).

  1. Select the following menu items: Powertrain / Hybrid Control / Trouble Codes.

  1. Read output DTCs (Click here).

    Result:
    Result
    Proceed to
    P0A1F-123 is not output.
    A
    P0A1F-123 is also output.
    B



B
GO TO DTC CHART (P0A1F-123) (Click here)
A


2.INSPECT BATTERY SMART UNIT
  1. Ensure the safety of the areas in front and at the back of the vehicle.

  1. Connect the Techstream to the DLC3.

  1. Turn the power switch on (READY).

  1. Select the following menu items: Powertrain / Hybrid Control / Data List / V1 to 15 Batt block.

  1. Fully warm up the engine and turn the air conditioning off.

  1. Firmly depress the brake pedal with your left foot.

  1. Move the shift lever to the D position.

  1. Record each battery block voltage from the data list (V1 to 15 Batt block) while fully depressing the accelerator pedal.

  1. Compare the battery block voltages (V1 to 15 Batt block) between the even and odd number groups in each combination shown in the table below.

    Odd number group
    Even number group
    Battery block voltages to be compared
    V1 BATT BLOCK
    V2 BATT BLOCK
    V1 BATT BLOCK - V2 BATT BLOCK
    V3 BATT BLOCK
    V4 BATT BLOCK
    V3 BATT BLOCK - V4 BATT BLOCK
    V5 BATT BLOCK
    V6 BATT BLOCK
    V5 BATT BLOCK - V6 BATT BLOCK
    V7 BATT BLOCK
    V8 BATT BLOCK
    V7 BATT BLOCK - V8 BATT BLOCK
    V9 BATT BLOCK
    V10 BATT BLOCK
    V9 BATT BLOCK - V10 BATT BLOCK
    V11 BATT BLOCK
    V12 BATT BLOCK
    V11 BATT BLOCK - V12 BATT BLOCK
    V13 BATT BLOCK
    V14 BATT BLOCK
    V13 BATT BLOCK - V14 BATT BLOCK
    V15 BATT BLOCK
    V12 BATT BLOCK
    V15 BATT BLOCK - V12 BATT BLOCK

  1. Check if the difference in voltage of each combination is 0.3 V or more.

    Result:
    Result
    Proceed to
    Difference in voltage of each combination is less than 0.3 V.
    A
    Difference in voltage of each combination is 0.3 V or more.
    B

    HINT:
    Difference in voltage of each combination is 0.3 V or more due to a battery smart unit internal error.



B
REPLACE BATTERY SMART UNIT (Click here)
A

REPLACE HV BATTERY (Click here)