Home › DRIVE LINE › DRIVE SHAFT › FRONT DRIVE SHAFT

FRONT DRIVE SHAFT > INSTALLATION

for Preparation Click here



1. INSTALL FRONT DRIVE SHAFT ASSEMBLY LH


    C165536
  1. Align the shaft splines and install the drive shaft assembly LH with a brass bar and hammer.

    NOTICE:
    1. Set the shaft snap ring with the opening facing down.
    2. Be careful not to damage the drive shaft dust cover, boot, or oil seal.
    3. Move the drive shaft assembly while keeping it level.



2. INSTALL FRONT DRIVE SHAFT ASSEMBLY RH
  1. Install the front drive shaft assembly RH.



    C167529
  1. Install a new bearing bracket hole snap ring and bolt.

    Torque:
    32 N*m{ 326 kgf*cm , 24 ft.*lbf }

    NOTICE:
    1. Do not damage the boot or oil seal.
    2. Move the drive shaft assembly while keeping it level.



3. INSTALL FRONT AXLE ASSEMBLY LH


    C165537E05
  1. Align the matchmarks and install the front drive shaft assembly to the front axle hub sub-assembly.



4. INSTALL NO. 1 FRONT SUSPENSION LOWER ARM LH


    C165929
  1. Install the front lower suspension arm to the front lower ball joint with the bolt and 2 nuts.

    Torque:
    92 N*m{ 938 kgf*cm , 68 ft.*lbf }



5. INSTALL TIE ROD ASSEMBLY LH
  1. Connect the tie rod assembly LH to the steering knuckle with the nut.

    Torque:
    49 N*m{ 500 kgf*cm , 36 ft.*lbf }

  1. Install a new cotter pin.

    NOTICE:
    Further tighten the nut up to 60° if the holes for the cotter pin are not aligned.



6. INSTALL FRONT SPEED SENSOR LH


    C165818E03
  1. Install the resin clamp and front speed sensor with the bolt.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }

    NOTICE:
    1. Prevent foreign matter from attaching to the sensor tip.
    2. Firmly insert the sensor body into the knuckle before tightening the bolt.
    3. After installing the sensor to the knuckle, make sure that there is no clearance between the sensor stay and knuckle. Also make sure that no foreign matter is stuck between the parts.
    4. To prevent interference between the sensor and magnetic rotor, do not rotate the sensor body during or after the insertion of the sensor body to the knuckle.



7. INSTALL FRONT STABILIZER LINK ASSEMBLY LH


    C165915
  1. Install the front stabilizer link assembly to the front shock absorber with the nut.

    Torque:
    74 N*m{ 755 kgf*cm , 55 ft.*lbf }

    NOTICE:
    If the ball joint turns together with the nut, use a hexagon wrench (6 mm) to hold the stud bolt.



8. INSTALL FRONT AXLE SHAFT NUT LH
  1. Clean the threaded parts on the drive shaft and front axle shaft nut LH using a non-residue solvent.

    HINT:
    1. Be sure to perform this work for a new drive shaft.
    2. Keep the threaded parts free of oil and foreign objects.



    C165538
  1. Using a socket wrench (30 mm), install a new front axle shaft nut.

    Torque:
    294 N*m{ 2996 kgf*cm , 216 ft.*lbf }

  1. Using a chisel and hammer, stake the front axle shaft nut.



9. INSTALL FRONT WHEELS

Torque:
103 N*m{ 1050 kgf*cm , 76 ft.*lbf }



10. ADD AND INSPECT HYBRID TRANSAXLE FLUID
  1. Add transaxle fluid.



    C173144E01
  1. Check that the fluid surface is within 5 mm (0.20 in.) from the lowest position of the inner surface of the differential filler plug opening.

    NOTICE:
    1. Keep the fluid temperature at 5°C (41°F) or higher.
    2. Stop the vehicle on a flat road.
    3. Insufficient or excessive amounts of transaxle fluid may be the cause of some trouble.

  1. Using a socket hexagon wrench 10 mm, temporarily tighten the filler plug and gasket.

  1. Enter 2WD inspection mode (Click here).

  1. After waiting for 1 minute or more, stop the engine.

  1. Using a socket hexagon wrench 10 mm, remove the filler plug and gasket.

  1. Add transaxle fluid.



    C173144E01
  1. Check that the fluid surface is within 5 mm (0.20 in.) from the lowest position of the inner surface of the differential filler plug opening.

    NOTICE:
    1. Keep the fluid temperature at 5°C (41°F) or higher.
    2. Stop the vehicle on a flat road.
    3. Recheck the transaxle fluid level after driving when exchanging fluid.
    4. Insufficient or excessive amounts of transaxle fluid may be the cause of some trouble.

  1. Check for leaks if the fluid level is low.

  1. Using a socket hexagon wrench 10 mm, install the filler plug, and a new gasket.

    Torque:
    39 N*m{ 398 kgf*cm , 29 ft.*lbf }



11. INSTALL NO. 2 ENGINE UNDER COVER
  1. Install the 2 bolts and No. 2 engine under cover.



12. INSTALL NO. 1 ENGINE UNDER COVER
  1. Install the 6 bolts, 2 screws, 2 clips and No. 1 engine under cover.



13. ADJUST FRONT WHEEL ALIGNMENT

HINT:
(Click here)



14. CHECK ABS SPEED SENSOR SIGNAL

HINT:
(Click here)