Home › RESTRAINTS › SUPPLEMENTAL RESTRAINT SYSTEM › AIRBAG SYSTEM

DTC    B1900/73    Short in Front Driver Side Pretensioner Squib Circuit

DTC    B1901/73    Open in Front Driver Side Pretensioner Squib Circuit

DTC    B1902/73    Short to GND in Front Driver Side Pretensioner Squib Circuit

DTC    B1903/73    Short to B+ in Front Driver Side Pretensioner Squib Circuit

for Preparation Click here


DESCRIPTION

The front driver side pretensioner squib circuit consists of the center airbag sensor assembly and the front seat outer belt assembly LH.
This circuit instructs the SRS to deploy when deployment conditions are met.
These DTCs are recorded when a malfunction is detected in the front driver side pretensioner squib circuit.

DTC No.
DTC Detection Condition
Trouble Area
B1900/73
  1. The center airbag sensor assembly receives a line short circuit signal 5 times in the front driver side pretensioner squib circuit during primary check.
  2. Front driver side pretensioner squib malfunction
  3. Center airbag sensor assembly malfunction
  1. Floor wire No. 2
  2. Front seat outer belt assembly LH (Front driver side pretensioner squib)
  3. Center airbag sensor assembly
B1901/73
  1. The center airbag sensor assembly receives an open circuit signal in the front driver side pretensioner squib circuit for 2 seconds.
  2. Front driver side pretensioner squib malfunction
  3. Center airbag sensor assembly malfunction
  1. Floor wire No. 2
  2. Front seat outer belt assembly LH (Front driver side pretensioner squib)
  3. Center airbag sensor assembly
B1902/73
  1. The center airbag sensor assembly receives a short circuit to ground signal in the front driver side pretensioner squib circuit for 0.5 seconds.
  2. Front driver side pretensioner squib malfunction
  3. Center airbag sensor assembly malfunction
  1. Floor wire No. 2
  2. Front seat outer belt assembly LH (Front driver side pretensioner squib)
  3. Center airbag sensor assembly
B1903/73
  1. The center airbag sensor assembly receives a short circuit to B+ signal in the front driver side pretensioner squib circuit for 0.5 seconds.
  2. Front driver side pretensioner squib malfunction
  3. Center airbag sensor assembly malfunction
  1. Floor wire No. 2
  2. Front seat outer belt assembly LH (Front driver side pretensioner squib)
  3. Center airbag sensor assembly

WIRING DIAGRAM


C157591E52


INSPECTION PROCEDURE

HINT:
  1. Perform the simulation method by selecting "check mode" (signal check) with Techstream (Click here).
  2. After selecting "check mode" (signal check), perform the simulation method by wiggling each connector of the airbag system or driving the vehicle on a city or rough road (Click here).

1.CHECK CONNECTORS


    C167985E06
  1. Turn the power switch off.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Check that the connectors are properly connected to the front seat outer belt assembly LH and center airbag sensor assembly.

    OK:
    The connectors are properly connected.

    HINT:
    If the connectors are connected securely, reconnect the connectors and proceed to the next inspection.

  1. Disconnect the connectors from the front seat outer belt assembly LH and center airbag sensor assembly.

  1. Check that the terminals of the connectors are not damaged.

    OK:
    The terminals are not deformed or damaged.

  1. Check that the floor wire No. 2 connector (on the front seat outer belt assembly LH side) is not damaged.

    OK:
    The lock button is not disengaged, and the claw of the lock is not deformed or damaged.



NG
REPLACE FLOOR WIRE NO. 2
OK


2.CHECK FRONT SEAT OUTER BELT ASSEMBLY LH (FRONT DRIVER SIDE PRETENSIONER SQUIB)


    C167997E03
  1. Connect the connector to the center airbag sensor assembly.

  1. Connect SST (resistance 2.1 Ω) to connector C.

    CAUTION:
    Never connect the tester to the front seat outer belt assembly LH (front driver side pretensioner squib) for measurement, as this may lead to a serious injury due to airbag deployment.

    NOTICE:
    1. Do not forcibly insert SST into the terminals of the connector when connecting.
    2. Insert SST straight into the terminals of the connector.

SST
09843-18061  
  1. Connect the negative (-) terminal cable to the battery.

  1. Turn the power switch on (IG), and wait for at least 60 seconds.

  1. Clear the DTCs stored in the memory (Click here).

  1. Turn the power switch off.

  1. Turn the power switch on (IG), and wait for at least 60 seconds.

  1. Check for DTCs (Click here).

    OK:
    DTC B1900, B1901, B1902, B1903, or 73 is not output.

    HINT:
    Codes other than DTC B1900, B1901, B1902, B1903, and 73 may be output at this time, but they are not related to this check.



NG
Go to step 3
OK

REPLACE FRONT SEAT OUTER BELT ASSEMBLY LH (Click here)  

3.CHECK FLOOR WIRE NO. 2 (FRONT DRIVER SIDE PRETENSIONER SQUIB CIRCUIT)


    C167998E03
  1. Turn the power switch off.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Disconnect SST from connector C.

  1. Disconnect the floor wire No. 2 from the center airbag sensor assembly.

  1. Check for a short to B+ in the circuit.

    1. Connect the negative (-) terminal cable to the battery.

    2. Turn the power switch on (IG).

    3. Measure the voltage according to the value(s) in the table below.

      Standard voltage:
      Tester Connection
      Switch Condition
      Specified Condition
      O4-1 (L+) - Body ground
      power switch on (IG)
      Below 1 V
      O4-2 (L-) - Body ground
      power switch on (IG)
      Below 1 V

  1. Check for an open in the circuit.

    1. Turn the power switch off.

    2. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

    3. Measure the resistance according to the value(s) in the table below.

      Standard resistance:
      Tester Connection
      Switch Condition
      Specified Condition
      O4-1 (L+) - O4-2 (L-)
      Always
      Below 1 Ω

  1. Check for a short to ground in the circuit.

    1. Measure the resistance according to the value(s) in the table below.

      Standard resistance:
      Tester Connection
      Switch Condition
      Specified Condition
      O4-1 (L+) - Body ground
      Always
      1 MΩ or higher
      O4-2 (L-) - Body ground
      Always
      1 MΩ or higher

  1. Check for a short in the circuit.

    1. Release the activation prevention mechanism built into connector B (Click here).

    2. Measure the resistance according to the value(s) in the table below.

      Standard resistance:
      Tester Connection
      Switch Condition
      Specified Condition
      O4-1 (L+) - O4-2 (L-)
      Always
      1 MΩ or higher



NG
REPLACE FLOOR WIRE NO. 2
OK


4.CHECK CENTER AIRBAG SENSOR ASSEMBLY


    C167999E02
  1. Restore the released activation prevention mechanism of connector B to the original condition.

  1. Connect the connectors to the front seat outer belt assembly LH and the center airbag sensor assembly.

  1. Connect the negative (-) terminal cable to the battery.

  1. Turn the power switch on (IG), and wait for at least 60 seconds.

  1. Clear the DTCs stored in the memory (Click here).

  1. Turn the power switch off.

  1. Turn the power switch on (IG), and wait for at least 60 seconds.

  1. Check for DTCs (Click here).

    OK:
    DTC B1900, B1901, B1902, B1903, or 73 is not output.

    HINT:
    Codes other than DTC B1900, B1901, B1902, B1903, and 73 may be output at this time, but they are not related to this check.



NG
REPLACE CENTER AIRBAG SENSOR ASSEMBLY (Click here)
OK

USE SIMULATION METHOD TO CHECK (Click here)