Home › RESTRAINTS › SUPPLEMENTAL RESTRAINT SYSTEM › OCCUPANT CLASSIFICATION SYSTEM

DTC    B1794    Open in Occupant Classification ECU Battery Positive Line

for Preparation Click here


DESCRIPTION

This circuit consists of the occupant classification ECU and the power source circuit (battery, fuse, and wire harness).
DTC B1794 is recorded when a malfunction is detected in the occupant classification ECU or the power source circuit.

HINT:
If DTC B1794 is output after turning the power switch from off to on (IG) to off 50 times in a row when a malfunction occurs in the power circuit for the occupant classification system.
This DTC is output if a malfunction is detected even after being cleared unless the normal system code is input.

DTC No.
DTC Detection Condition
Trouble Area
B1794
  1. The power switch is turned from off to on (IG), hold for 10 seconds or more, and turned off again 50 times in a row when a malfunction occurs in the power circuit for the occupant classification system.
  2. Occupant classification ECU malfunction
  1. Battery
  2. ECU-B fuse
  3. Wire harness
  4. Occupant classification ECU
When DTC B1650/32 is detected as a result of troubleshooting for the AIRBAG SYSTEM, check the DTCs stored in the occupant classification ECU. When DTC B1794 is output, perform troubleshooting for the DTC.


WIRING DIAGRAM


C170488E02


INSPECTION PROCEDURE

1.CHECK BATTERY
  1. Measure the voltage of the battery.

    Standard voltage:
    11 to 14 V



NG
REPLACE BATTERY
OK


2.CHECK FUSE
  1. Measure the resistance of the ECU-B fuse.

    Standard resistance:
    Below 1 Ω



NG
REPLACE FUSE
OK


3.CHECK WIRE HARNESS (SOURCE VOLTAGE)


    C169182E02
  1. Turn the power switch off.

  1. Disconnect the negative (-) terminal cable from the battery.

  1. Disconnect the connector from the occupant classification ECU.

  1. Connect the negative (-) terminal cable to the battery.

  1. Turn the power switch on (IG).

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    a3-1 (+B) - Body ground
    Always
    11 to 14 V
    a3-7 (IG) - Body ground
    power switch on (IG)
    11 to 14 V

  1. Turn the power switch off.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    a3-3 (GND) - Body ground
    Always
    Below 1 Ω



NG
REPLACE WIRE HARNESS
OK


4.CHECK DTC
  1. Turn the power switch off.

  1. Disconnect the negative (-) terminal cable from the battery.

  1. Connect the connector to the occupant classification ECU.

  1. Connect Techstream to the DLC3.

  1. Connect the negative (-) terminal cable to the battery.

  1. Turn the power switch on (IG).

  1. Clear the DTCs stored in the occupant classification ECU (Click here).

  1. Clear the DTCs stored in the center airbag sensor assembly (Click here).

  1. Turn the power switch off.

  1. Turn the power switch on (IG), and wait for at least 10 seconds.

  1. Using Techstream, check for DTCs of the occupant classification ECU (Click here).

    OK:
    DTC B1794 is not output.

    HINT:
    Codes other than DTC B1794 may be output at this time, but they are not related to this check.



NG
Go to step 5
OK

USE SIMULATION METHOD TO CHECK (Click here)  

5.REPLACE OCCUPANT CLASSIFICATION ECU
  1. Turn the power switch off.

  1. Disconnect the negative (-) terminal cable from the battery.

  1. Replace the occupant classification ECU (Click here).


NEXT


6.PERFORM ZERO POINT CALIBRATION
  1. Connect the negative (-) terminal cable to the battery.

  1. Connect Techstream to the DLC3.

  1. Turn the power switch on (IG).

  1. Using Techstream, perform the "zero point calibration" (Click here).

    OK:
    "Zero Point Calibration is complete." is displayed.


NEXT


7.PERFORM SENSITIVITY CHECK
  1. Using Techstream, perform "sensitivity check" (Click here).

    Standard:
    27 to 33 kg (59.52 to 72.75 lb)


NEXT

END