Home › RESTRAINTS › SUPPLEMENTAL RESTRAINT SYSTEM › AIRBAG SYSTEM

DTC    B1622/81    Lost Communication with Driver Side - Side Airbag Sensor Assembly

DTC    B1623/81    Driver Side - Side Airbag Sensor Assembly Initialization Incomplete

DTC    B1632/81    Lost Communication with Driver Side Rear Airbag Sensor

DTC    B1633/81    Driver Side Rear Airbag Sensor Initialization Incomplete

DTC    B1642/81    Lost Communication with Driver Side Satellite Sensor Bus

DTC    B1643/81    Driver Side Satellite Sensor Bus Initialization Incomplete

for Preparation Click here


DESCRIPTION

The driver side - side collision sensor circuit (to determine deployment of the front seat side airbag assembly LH and curtain shield airbag assembly LH) is composed of the center airbag sensor assembly, side airbag sensor LH, and rear airbag sensor LH.
The side airbag sensor LH and rear airbag sensor LH detect impacts to the vehicle and send signals to the center airbag sensor assembly to determine if the airbag should be deployed.
These DTCs are recorded when a malfunction is detected for the driver side - side collision sensor circuit (to determine deployment of the front seat side airbag assembly LH and curtain shield airbag assembly LH).

DTC No.
DTC Detection Condition
Trouble Area
B1622/81
B1623/81
B1632/81
B1633/81
B1642/81
B1643/81
  1. The center airbag sensor assembly receives a line short circuit signal, an open circuit signal, a short circuit to ground signal or a short circuit to B+ signal in the driver side - side collision sensor circuit (to determine deployment of the front seat side airbag assembly LH and curtain shield airbag assembly LH) for 2 seconds.
  2. Side airbag sensor LH malfunction
  3. Rear airbag sensor LH malfunction
  4. Center airbag sensor assembly malfunction
  1. Floor wire No. 2
  2. Side airbag sensor LH
  3. Rear airbag sensor LH
  4. Center airbag sensor assembly

WIRING DIAGRAM


C165789E04


INSPECTION PROCEDURE

1.CHECK PRESENT DTC


    C167949E01
  1. Turn the power switch on (IG), and wait for at least 60 seconds.

  1. Check for present DTCs (Click here).

    Result:
    Result
    Proceed to
    Present DTC B1623 or B1643 is output
    A
    Present DTC B1642 or 81 is output
    B
    Present DTC B1632 or B1633 is output
    C
    Present DTC B1622 is output
    D
    Present DTC B1622, B1623, B1632, B1633, B1642, B1643 or 81 is not output
    E

    HINT:
    1. DTCs indicating communication errors will be changed to DTCs indicating errors in initialization by turning the power switch off and then on (IG) again.
    2. Codes other than present DTC B1622, B1623, B1632, B1633, B1642, B1643, and 81 may be output at this time, but they are not related to this check.



B
Go to step 3

C
Go to step 14

D
Go to step 21

E
USE SIMULATION METHOD TO CHECK (Click here)
A


2.CHECK PAST DTC
  1. Check for past DTCs (Click here).

    Result:
    Result
    Proceed to
    Past DTC B1622 or B1632 is not output
    A
    Past DTC B1632 is output
    B
    Past DTC B1622 is output
    C

    HINT:
    Codes other than past DTC B1622 and B1632 may be output at this time, but they are not related to this check.



B
Go to step 14

C
Go to step 21
A


3.CHECK CONNECTORS
  1. Turn the power switch off.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Check that the connectors are properly connected to the center airbag sensor assembly, side airbag sensor LH and the rear airbag sensor LH.

    OK:
    The connectors are properly connected.

    HINT:
    If the connectors are not connected securely, reconnect the connectors and proceed to the next inspection.

  1. Disconnect the connectors from the center airbag sensor assembly, side airbag sensor LH and rear airbag sensor LH.

  1. Check that the terminals of the connectors are not damaged.

    OK:
    The terminals are not deformed or damaged.



NG
REPLACE FLOOR WIRE NO. 2
OK


4.CHECK FLOOR WIRE NO. 2 (OPEN)


    C167950E03
  1. Using SST, connect terminals 24 (BBD+) and 23 (BBD-) of connector B.

    NOTICE:
    Do not forcibly insert SST into the terminals of the connector when connecting.

SST
09843-18040  
  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    O3-4 (BBL+) - O3-3 (BBL-)
    Always
    Below 1 Ω



NG
REPLACE FLOOR WIRE NO. 2
OK


5.CHECK FLOOR WIRE NO. 2 (SHORT)


    C167951E02
  1. Disconnect SST from connector B.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    O3-4 (BBL+) - O3-3 (BBL-)
    Always
    1 MΩ or higher



NG
REPLACE FLOOR WIRE NO. 2
OK


6.CHECK FLOOR WIRE NO. 2 (SHORT TO B+)


    C167951E02
  1. Connect the negative (-) terminal cable to the battery.

  1. Turn the power switch on (IG).

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    O3-4 (BBL+) - Body ground
    power switch on (IG)
    Below 1 V
    O3-3 (BBL-) - Body ground
    power switch on (IG)
    Below 1 V



NG
REPLACE FLOOR WIRE NO. 2
OK


7.CHECK FLOOR WIRE NO. 2 (SHORT TO GROUND)


    C167951E02
  1. Turn the power switch off.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    O3-4 (BBL+) - Body ground
    Always
    1 MΩ or higher
    O3-3 (BBL-) - Body ground
    Always
    1 MΩ or higher



NG
REPLACE FLOOR WIRE NO. 2
OK


8.CHECK FLOOR WIRE NO. 2 (OPEN)


    C145449E11
  1. Using SST, connect terminals 2 (BCL+) and 1 (BCL-) of connector C.

    NOTICE:
    Do not forcibly insert SST into the terminals of the connector when connecting.

SST
09843-18040  
  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    O3-1 (BCL+) - O3-2 (BCL-)
    Always
    Below 1 Ω



NG
REPLACE FLOOR WIRE NO. 2
OK


9.CHECK FLOOR WIRE NO. 2 (SHORT)


    C145445E07
  1. Disconnect SST from connector C.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    O3-1 (BCL+) - O3-2 (BCL-)
    Always
    1 MΩ or higher



NG
REPLACE FLOOR WIRE NO. 2
OK


10.CHECK FLOOR WIRE NO. 2 (SHORT TO B+)


    C145445E07
  1. Connect the negative (-) terminal cable to the battery.

  1. Turn the power switch on (IG).

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    O3-1 (BCL+) - Body ground
    power switch on (IG)
    Below 1 V
    O3-2 (BCL-) - Body ground
    power switch on (IG)
    Below 1 V



NG
REPLACE FLOOR WIRE NO. 2
OK


11.CHECK FLOOR WIRE NO. 2 (SHORT TO GROUND)


    C145445E07
  1. Turn the power switch off.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    O3-1 (BCL+) - Body ground
    Always
    1 MΩ or higher
    O3-2 (BCL-) - Body ground
    Always
    1 MΩ or higher



NG
REPLACE FLOOR WIRE NO. 2
OK


12.CHECK SIDE AIRBAG SENSOR LH


    C123806E01
  1. Connect the connectors to the rear airbag sensor LH and center airbag sensor assembly.

  1. Interchange the side airbag sensor RH with LH and connect the connectors to them.

  1. Connect the negative (-) terminal cable to the battery.

  1. Turn the power switch on (IG), and wait for at least 60 seconds.

  1. Clear the DTCs stored in the the memory (Click here).

  1. Turn the power switch off.

  1. Turn the power switch on (IG), and wait for at least 60 seconds.

  1. Check for DTCs (Click here).

    Result:
    Result
    Proceed to
    DTC B1623, B1642, B1643, or 81 is output
    A
    DTC B1628, B1647, B1648, or 82 is output
    B
    DTCs B1623, B1642, B1643, or 81 and B1628, B1647, B1648, or 82 are not output
    C

    HINT:
    Codes other than DTC B1623, B1642, B1643, or 81 and B1628, B1647, B1648, or 82 may be output at this time, but they are not related to this check.



B
REPLACE SIDE AIRBAG SENSOR LH (Click here)

C
USE SIMULATION METHOD TO CHECK (Click here)
A


13.CHECK REAR AIRBAG SENSOR LH


    C167953E01
  1. Turn the power switch off.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Return the side airbag sensor RH and LH to their original positions and connect the connectors to them.

  1. Interchange the rear airbag sensor RH with LH and connect the connectors to them.

  1. Connect the negative (-) terminal cable to the battery.

  1. Turn the power switch on (IG), and wait for at least 60 seconds.

  1. Clear the DTCs stored in the memory (Click here).

  1. Turn the power switch off.

  1. Turn the power switch on (IG), and wait for at least 60 seconds.

  1. Check for DTCs (Click here).

    Result:
    Result
    Proceed to
    DTC B1623, B1642, B1643, or 81 and B1628, B1647, B1648, or 82 are not output.
    A
    DTC B1623, B1642, B1643, or 81 is output.
    B
    DTC B1628, B1647, B1648, or 82 is output.
    C

    HINT:
    Codes other than DTC B1623, B1642, B1643, or 81 and B1628, B1647, B1648, or 82 may be output at this time, but they are not related to this check.



B
REPLACE CENTER AIRBAG SENSOR ASSEMBLY (Click here)

C
REPLACE REAR AIRBAG SENSOR LH (Click here)
A

USE SIMULATION METHOD TO CHECK (Click here)  

14.CHECK CONNECTORS
  1. Turn the power switch off.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Check that the connectors are properly connected to the side airbag sensor LH and rear airbag sensor LH.

    OK:
    The connectors are properly connected.

    HINT:
    If the connectors are not connected securely, reconnect the connectors and proceed to the next inspection.

  1. Disconnect the connectors from the side airbag sensor LH and rear airbag sensor LH.

  1. Check that the terminals of connectors are not damaged.

    OK:
    The terminals are not deformed or damaged.



NG
REPLACE FLOOR WIRE NO. 2
OK


15.CHECK FLOOR WIRE NO. 2 (OPEN)


    C145449E11
  1. Using SST, connect terminals 2 (BCL+) and 1 (BCL-) of connector C.

    NOTICE:
    Do not forcibly insert SST into the terminals of the connector when connecting.

SST
09843-18040  
  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    O3-1 (BCL+) - O3-2 (BCL-)
    Always
    Below 1 Ω



NG
REPLACE FLOOR WIRE NO. 2
OK


16.CHECK FLOOR WIRE NO. 2 (SHORT)


    C145445E07
  1. Disconnect SST from connector C.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    O3-1 (BCL+) - O3-2 (BCL-)
    Always
    1 MΩ or higher



NG
REPLACE FLOOR WIRE NO. 2
OK


17.CHECK FLOOR WIRE NO. 2 (SHORT TO B+)


    C145445E07
  1. Connect the negative (-) terminal cable to the battery.

  1. Turn the power switch on (IG).

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    O3-1 (BCL+) - Body ground
    power switch on (IG)
    Below 1 V
    O3-2 (BCL-) - Body ground
    power switch on (IG)
    Below 1 V



NG
REPLACE FLOOR WIRE NO. 2
OK


18.CHECK FLOOR WIRE NO. 2 (SHORT TO GROUND)


    C145445E07
  1. Turn the power switch off.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    O3-1 (BCL+) - Body ground
    Always
    1 MΩ or higher
    O3-2 (BCL-) - Body ground
    Always
    1 MΩ or higher



NG
REPLACE FLOOR WIRE NO. 2
OK


19.CHECK SIDE AIRBAG SENSOR LH


    C167957E02
  1. Connect the connector to the rear airbag sensor LH.

  1. Interchange the side airbag sensor RH with LH and connect the connectors to them.

  1. Connect the negative (-) terminal cable to the battery.

  1. Turn the power switch on (IG), and wait for at least 60 seconds.

  1. Clear the DTCs stored in the the memory (Click here).

  1. Turn the power switch off.

  1. Turn the power switch on (IG), and wait for at least 60 seconds.

  1. Check for DTCs (Click here).

    Result:
    Result
    Proceed to
    DTC B1632 or B1633 is output
    A
    DTC B1637 or B1638 is output
    B
    DTC B1632 or B1633 and B1637 or B1638 are not output
    C

    HINT:
    Codes other than DTC B1632 or B1633 and B1637 or B1638 may be output at this time, but they are not related to this check.



B
REPLACE SIDE AIRBAG SENSOR LH (Click here)

C
USE SIMULATION METHOD TO CHECK (Click here)
A


20.CHECK REAR AIRBAG SENSOR LH


    C166174E01
  1. Turn the power switch off.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Return the side airbag sensor RH and LH to their original positions and connect the connectors to them.

  1. Interchange the rear airbag sensor RH with LH and connect the connectors to them.

  1. Connect the negative (-) terminal cable to the battery.

  1. Turn the power switch on (IG), and wait for at least 60 seconds.

  1. Clear the DTCs stored in the memory (Click here).

  1. Turn the power switch off.

  1. Turn the power switch on (IG), and wait for at least 60 seconds.

  1. Check for DTCs (Click here).

    Result:
    Result
    Proceed to
    DTC B1632 or B1633 and B1637 or B1638 are not output
    A
    DTC B1632 or B1633 is output
    B
    DTC B1637 or B1638 is output
    C

    HINT:
    Codes other than DTC B1632 or B1633 and B1637 or B1638 may be output at this time, but they are not related to this check.



B
REPLACE CENTER AIRBAG SENSOR ASSEMBLY (Click here)

C
REPLACE REAR AIRBAG SENSOR LH (Click here)
A

USE SIMULATION METHOD TO CHECK (Click here)  

21.CHECK SIDE AIRBAG SENSOR LH


    C167957E02
  1. Turn the power switch off.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Interchange the side airbag sensor RH with LH and connect the connectors to them.

  1. Connect the negative (-) terminal cable to the battery.

  1. Turn the power switch on (IG), and wait for at least 60 seconds.

  1. Clear the DTCs stored in the memory (Click here).

  1. Turn the power switch off.

  1. Turn the power switch on (IG), and wait for at least 60 seconds.

  1. Check for DTCs (Click here).

    Result:
    Result
    Proceed to
    DTC B1622 and B1627 are not output
    A
    DTC B1622 is output
    B
    DTC B1627 is output
    C

    HINT:
    Codes other than DTC B1622 and B1627 may be output at this time, but they are not related to this check.



B
REPLACE CENTER AIRBAG SENSOR ASSEMBLY (Click here)

C
REPLACE SIDE AIRBAG SENSOR LH (Click here)
A

USE SIMULATION METHOD TO CHECK (Click here)