Home › BODY ELECTRICAL › DOOR LOCK › SMART KEY SYSTEM

SMART KEY SYSTEM > All Door Entry Lock/Unlock Functions and Wireless Functions do not Operate

for Preparation Click here


DESCRIPTION

When the entry functions and wireless door lock functions do not operate, a malfunction or wave interference may be occurring in either of the following: 1) signal communication line between the door control receiver and certification ECU (smart key ECU assembly) (line is used for entry and wireless functions); or 2) electrical key transmitter.

WIRING DIAGRAM


B164402E05


INSPECTION PROCEDURE

NOTICE:
  1. Before performing the inspection, check that there are no problems related to "CAN COMMUNICATION SYSTEM" and "LIN COMMUNICATION SYSTEM".
  2. Check that there are not electrical key transmitters in the vehicle.
  3. Before performing the inspection, check that DTC B1242 is not output (Click here).

1.CHECK POWER DOOR LOCK OPERATION
  1. When the door control switch on the master switch assembly is operated, check that the locked doors unlock (Click here).

    OK:
    Locked doors unlock.



NG
GO TO POWER DOOR LOCK CONTROL SYSTEM (Click here)
OK


2.CHECK ELECTRICAL KEY TRANSMITTER
  1. When another registered door control transmitter is used, check that the wireless and entry functions operate normally (Click here).

    Result:
    Result
    Proceed to
    Entry functions do not operate
    A
    Entry functions operate and electrical key transmitter does not operate
    B



A
Go to step 5
B


3.CHECK ELECTRICAL KEY TRANSMITTER (LED)
  1. Check that the transmitter's LED illuminates 3 times when the switch is pressed 3 times.

    Result:
    Result
    Proceed to
    Transmitter's LED illuminates 3 times when switch is pressed 3 times
    A
    Transmitter's LED does not illuminate the second or third time
    B
    Transmitter's LED does not illuminate 3 times when switch is pressed 3 times
    C

    HINT:
    If the transmitter's LED does not illuminate the second or third time, replace the transmitter battery as it is depleted.



A
REPLACE ELECTRICAL KEY TRANSMITTER

B
REPLACE ELECTRICAL TRANSMITTER BATTERY (Click here)
C


4.INSPECT TRANSMITTER BATTERY (VOLTAGE)


    B171393
  1. Remove the battery from the electrical key transmitter that does not operate. Attach a lead wire (0.6 mm (0.0236 in.) in diameter or less including wire sheath) with tape or equivalent to the negative terminal (Click here).

    NOTICE:
    Do not wrap the lead wire around a terminal, wedge it between the terminals, or solder it. A terminal may be deformed or damaged, and the battery will not be able to be installed correctly.

  1. Carefully pull the lead wire out from the position shown in the illustration and install the previously removed transmitter battery.



    B171394E01
  1. Using an oscilloscope, check the transmitter battery voltage waveform.

    HINT:
    When measuring the battery voltage, while operating the lock switch of a door outside handle, bring the electrical key transmitter within the entry operating range to perform the measurement. For the entry operating range, refer to SYSTEM DESCRIPTION (Click here).

    Standard voltage:
    Item
    Content
    Tester Connection
    Battery positive (+) - Battery negative (-)
    Tool Setting
    0.5 V/DIV., 100 ms/DIV.
    Condition
    Power switch OFF, all doors closed and lock switch pushed
    Specified Condition
    2.2 to 3.2 V (Refer to the waveform)



NG
REPLACE ELECTRICAL TRANSMITTER BATTERY (Click here)
OK

REPLACE ELECTRICAL KEY TRANSMITTER 

5.CHECK WAVE ENVIRONMENT
  1. Bring the electrical key transmitter near the door control receiver, and perform a wireless and smart operation check.

    HINT:
    1. When the electrical key transmitter is brought near the door control receiver, the possibility of wave interference decreases, and it can be determined if wave interference is causing the problem symptom.
    2. If the inspection result is that the problem only occurs in certain locations or times of day, the possibility of wave interference is high. Also, added vehicle components may cause wave interference. If installed, remove them and perform the operation check.

    OK:
    Wireless and entry functions operate normally.



NG
Go to step 6
OK

AFFECTED BY WAVE INTERFERENCE 

6.INSPECT FUSE (EFI NO. 1)
  1. Remove the EFI NO. 1 fuse from the main body ECU (instrument panel junction block).

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    EFI NO. 1 fuse
    Always
    Below 1 Ω



NG
REPLACE FUSE (EFI NO. 1)
OK


7.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU - BATTERY AND GROUND)


    B178879E04
  1. Measure the voltage and resistance according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Condition
    Specified Condition
    D40-1 (+B) - Body ground
    Always
    11 to 14 V

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    D40-17 (E) - Body ground
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


8.CHECK HARNESS AND CONNECTOR (DOOR CONTROL RECEIVER - CERTIFICATION ECU)


    B171406E01
  1. Disconnect the certification ECU (smart key ECU assembly) and door control receiver connectors.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    D40-39 (RSSI) - O26-2 (RSSI)
    Always
    Below 1 Ω
    D40-38 (RDA) - O26-5 (DATA)
    Always
    Below 1 Ω
    D40-29 (RC0) - O26-4 (+5)
    Always
    Below 1 Ω
    D40-39 (RSSI) - Body ground
    Always
    10 kΩ or higher
    D40-38 (RDA) - Body ground
    Always
    10 kΩ or higher
    D40-29 (RC0) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


9.REPLACE DOOR CONTROL RECEIVER
  1. Replace the door control receiver (Click here).


NEXT


10.CHECK DOOR CONTROL RECEIVER (OPERATION)
  1. Check that the wireless and entry functions operate normally.

    OK:
    Wireless and entry functions operate normally.



NG
REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) (Click here)
OK

END (DOOR CONTROL RECEIVER IS DEFECTIVE)