Home › BODY › ENGINE HOOD / DOOR › FUEL LID OPENER SYSTEM

FUEL LID OPENER SYSTEM > "CLOSE FUEL LID" Remains Displayed at Multi-information Display

for Preparation Click here


DESCRIPTION

The hybrid vehicle control ECU detects the fuel lid courtesy switch status and transmits this data to the combination meter. According to the data from the hybrid vehicle control ECU, the combination meter displays "CLOSE FUEL LID" on the multi-information display if the fuel lid is open, and does not display "CLOSE FUEL LID" if the fuel lid is closed.
When the fuel lid is closed but "CLOSE FUEL LID" remains displayed on the multi-information display, one of the following may be malfunctioning: 1) fuel lid courtesy switch, 2) wire harness or connector, 3) hybrid vehicle control ECU, or 4) meter / gauge system.

WIRING DIAGRAM


B178874E02


INSPECTION PROCEDURE

NOTICE:
If the hybrid vehicle control ECU is replaced, register the ECU communication ID (Click here).

1.READ VALUE USING TECHSTREAM (FUEL LID COURTESY SWITCH)
  1. Connect the Techstream to the DLC3.

  1. Turn the power switch on (IG).

  1. Turn the Techstream on.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List.

  1. Read the Data List according to the display on the Techstream.

    Engine and ECT (Hybrid Vehicle Control ECU): 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Fuel Lid
    Fuel lid courtesy switch status: ON or OFF
    ON: Fuel lid is opened
    OFF: Fuel lid is closed
    -

    OK:
    On the Techstream screen, the item changes between ON and OFF according to the chart above.



NG
Go to step 6
OK


2.CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU - COMBINATION METER)


    B178872E01
  1. Disconnect the hybrid vehicle control ECU connector.

  1. Disconnect the combination meter connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    D35-7 (LST1) - E1-12 (FUWI)
    Always
    Below 1 Ω
    D35-6 (LST2) - E1-13 (FUCI)
    Always
    Below 1 Ω
    D35-7 (LST1) - Body ground
    Always
    10 kΩ or higher
    D35-6 (LST2) - Body ground
    Always
    10 kΩ or higher

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Condition
    Specified Condition
    D35-7 (LST1) - Body ground
    Power switch on (IG)
    Below 1 V
    D35-6 (LST2) - Body ground
    Power switch on (IG)
    Below 1 V

    NOTICE:
    Turning the power switch on (IG) with the hybrid vehicle control ECU connector disconnected causes other DTCs to be stored. Clear the DTCs after performing this inspection.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3.REPLACE HYBRID VEHICLE CONTROL ECU
  1. Replace the hybrid vehicle control ECU (Click here).


NEXT


4.REGISTER ECU COMMUNICATION ID (HYBRID VEHICLE CONTROL ECU - ID CODE BOX)
  1. Register the ECU communication ID (Click here).


NEXT


5.CHECK METER / GAUGE SYSTEM (MULTI-INFORMATION DISPLAY)
  1. Check the multi-information display when the fuel lid is closed.

    OK:
    "CLOSE FUEL LID" is not displayed on the multi-information display.



NG
REPLACE COMBINATION METER ASSEMBLY (Click here)
OK

END (HYBRID VEHICLE CONTROL ECU IS DEFECTIVE) 

6.INSPECT FUEL LID COURTESY SWITCH


    B178864E01
  1. Remove the fuel lid courtesy switch (Click here).

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    1 - 2
    Courtesy switch free (fuel lid open)
    10 kΩ or higher
    1 - 2
    Courtesy switch pushed (fuel lid closed)
    Below 1 Ω



NG
REPLACE FUEL LID COURTESY SWITCH
OK


7.CHECK HARNESS AND CONNECTOR (FUEL LID COURTESY SWITCH - HYBRID VEHICLE CONTROL ECU)


    B178870E01
  1. Disconnect the fuel lid courtesy switch connector.

  1. Disconnect the hybrid vehicle control ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    D35-13 (LIDO) - O48-1
    Always
    Below 1 Ω
    D35-13 (LIDO) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


8.CHECK HARNESS AND CONNECTOR (FUEL LID COURTESY SWITCH - BODY GROUND)


    B178887E01
  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    O48-2 - Body ground
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE HYBRID VEHICLE CONTROL ECU (Click here)