Home › BRAKE › BRAKE CONTROL › REAR SPEED SENSOR

REAR SPEED SENSOR > REMOVAL

for Preparation Click here


HINT:
  1. Use the same procedure for the LH side and RH side.
  2. The following procedure is for the LH side.
  3. If the sensor rotor needs to be replaced, replace it together with the outboard joint shaft assembly (Click here).



1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).



2. REMOVE SERVICE PLUG GRIP

CAUTION:
  1. Remove the service plug to interrupt a high voltage circuit at the time of the check.
  2. Keep the removed service plug in your pocket to prevent other technicians from accidentally reconnecting it while you are servicing the vehicle.
  3. All the high voltage wiring connectors are colored in orange.



    A175634
  1. Remove the 5 clips and door scuff plate LH.



    A175635
  1. Remove the 2 clips and reclining hinge cover.



    A175636
  1. Wear insulated glove and remove the service plug grip, after sliding up the lever of the service plug grip.

    CAUTION:
    1. Keep the removed service plug in your pocket to prevent other technicians from accidentally reconnecting it while you are servicing the vehicle.
    2. After removing the service plug grip, do not touch the high voltage connectors and terminals for 5 minutes.

    NOTICE:
    After removing the service plug grip, do not operate the power switch as it may damage the hybrid vehicle control ECU.



3. REMOVE REAR DOOR SCUFF PLATE LH


    B173228
  1. Disengage the 5 claws, 3 clips and guide, and remove the rear door scuff plate LH.



4. REMOVE REAR DOOR OPENING TRIM WEATHERSTRIP LH


    B173232
  1. Remove the rear door opening trim weatherstrip LH.



5. REMOVE DECK BOARD ASSEMBLY


    B173240
  1. Remove the deck board assembly.



6. REMOVE NO. 3 DECK BOARD SUB-ASSEMBLY


    B173242
  1. Disengage the 2 guides and remove the No. 3 deck board sub-assembly.



7. REMOVE NO. 2 DECK BOARD SUB-ASSEMBLY


    B173244
  1. Disengage the 2 guides and remove the No. 2 deck board sub-assembly.



8. REMOVE TONNEAU COVER ASSEMBLY (w/ Tonneau Cover)
  1. Remove the tonneau cover assembly.



9. REMOVE REAR NO. 1 FLOOR BOARD (w/o Rear No. 2 Seat)


    B175152
  1. Disengage the 3 clips and the 3 guides, and remove the rear No. 1 floor board.



10. REMOVE REAR SEAT SIDE COVER LH (w/ Rear No. 2 Seat)


    B173607
  1. Disengage the 2 clips and remove the rear seat side cover LH.



11. REMOVE DECK SIDE TRIM BOX LH


    B173243E01
  1. Remove the 2 deck side trim clips and clip.



  1. Remove the deck side trim box LH as shown in the illustration.


    B178554



12. REMOVE REAR SEAT SIDE COVER RH (w/ Rear No. 2 Seat)


    B173608
  1. Disengage the 2 clips and remove the rear seat side cover RH.



13. REMOVE JACK CARRIER SUPPORT


14. REMOVE JACK CARRIER CUSHION


    B178550
  1. Remove the jack carrier cushion.



15. REMOVE JACK ASSEMBLY


    B173245
  1. Remove the jack assembly.



16. REMOVE JACK CARRIER ASSEMBLY


    B178548
  1. Using a screwdriver, disengage the 3 claws and remove the jack carrier assembly.



17. REMOVE DECK SIDE TRIM BOX RH


    B173247E01
  1. Remove the 2 deck side trim clips and clip.



  1. Remove the deck side trim box RH as shown in the illustration.


    B178552



18. REMOVE DECK FLOOR BOARD ASSEMBLY (w/o Rear No. 2 Seat)


    B178560
  1. Remove the 4 bolts and 4 nuts.

  1. Remove the deck floor board assembly.



19. REMOVE REAR MAT


    B173249
  1. Remove the rear mat.



20. REMOVE DECK FLOOR BOARD ASSEMBLY (w/ Rear No. 2 Seat)


    B178561
  1. Disengage the 3 claws.

  1. Remove the 2 nuts and the deck floor board assembly.



21. REMOVE REAR DECK FLOOR BOX (w/o Rear No. 2 Seat)


    B173679
  1. Remove the 2 nuts and the deck floor box.



22. REMOVE REAR NO. 2 SEAT INNER BELT ASSEMBLY (w/ Rear No. 2 Seat)


    B170935
  1. Remove the bolt and rear No. 2 seat inner belt assembly.

    HINT:
    Use the same procedure for the RH side and LH side.



23. DISCONNECT REAR SEAT LAP TYPE BELT ASSEMBLY LH (w/ Rear No. 2 Seat)


    B170936
  1. Remove the bolt and disconnect the rear seat lap type belt assembly LH.



24. DISCONNECT REAR SEAT LAP TYPE BELT ASSEMBLY RH (w/ Rear No. 2 Seat)

HINT:
Use the same procedure for the RH side and the LH side.



25. REMOVE REAR NO. 2 SEAT ASSEMBLY (w/ Rear No. 2 Seat)


    B173781
  1. Remove the 4 bolts and the rear No. 2 seat assembly.



26. REMOVE REAR FLOOR FINISH PLATE


    B173609
  1. Disengage the 4 clips and the 4 claws, and remove the rear floor finish plate.



27. REMOVE DECK SIDE TRIM COVER LH


    B173595E01
  1. Using a screwdriver, disengage the 2 claws and remove the deck side trim cover LH.

    HINT:
    Tape the screwdriver tip before use.



28. REMOVE DECK SIDE TRIM LH


    B173596
  1. Remove the bolt.



    B173623
  1. Disengage the 4 claws and the 3 guides, and remove the deck side trim LH as shown in the illustration.



29. REMOVE SIDE TRIM COVER LH (w/o Rear Seat Entertainment System)


    B173597
  1. Disengage the 10 claws and remove the side trim cover LH.



30. REMOVE POWER OUTLET SOCKET BEZEL (w/ Rear Seat Entertainment System)


    B173680
  1. Disengage the 4 claws.



    B173681
  1. Disconnect each connector and remove the power outlet socket bezel.



31. REMOVE REAR COMBINATION LIGHT SERVICE COVER LH


    B173611E01
  1. Using a screwdriver, disengage the 6 claws and 2 guides, and remove the rear combination light service cover LH.

    HINT:
    Tape the screwdriver tip before use.



32. REMOVE REAR POWER POINT SOCKET ASSEMBLY
  1. Disconnect the connector.



    E151327
  1. Disengage the claw and remove the rear power point socket assembly.



33. REMOVE REAR POWER OUTLET SOCKET COVER


    E151328
  1. Disengage the 2 claws and remove the rear power outlet socket cover.



34. REMOVE REAR DECK TRIM COVER (w/o Remote Folding Function)


    B173602
  1. Disengage the 10 claws and remove the rear deck trim cover.



35. REMOVE RECLINING REMOTE CONTROL LEVER BEZEL LH (w/ Remote Folding Function)


    B173603
  1. Disengage the 5 claws and remove the reclining remote control lever bezel LH.



36. REMOVE ROPE HOOK ASSEMBLY (for LH Side)


    B173598E01
  1. for Front Side:

    1. Using a screwdriver, disengage the 2 claws.

      HINT:
      Tape the screwdriver tip before use.

    2. Remove the bolt and the rope hook assembly.



    B173600E01
  1. for Rear Side:

    1. Using a screwdriver, disengage the 2 claws.

      HINT:
      Tape the screwdriver tip before use.

    2. Remove the bolt and rope hook assembly.



37. REMOVE NO. 2 DECK SIDE TRIM HOOK


    B173612
  1. Remove the screw and the No. 2 deck side trim hook.



38. REMOVE FRONT DECK SIDE TRIM COVER LH


    B173604E01
  1. Using a screwdriver, disengage the 4 claws and remove the 2 front deck side trim covers LH.

    HINT:
    Tape the screwdriver tip before use.



39. REMOVE REAR NO. 1 SEAT OUTER BELT ASSEMBLY LH


    B170933
  1. Remove the bolt and disconnect the floor end of the rear No. 1 seat outer belt assembly.



40. REMOVE DECK TRIM SIDE PANEL ASSEMBLY LH
  1. Remove the 2 bolts.

  1. Remove the 2 clips.



  1. Disengage the 7 claws and 4 clips, and remove the deck trim side panel assembly LH.


    B173613



41. REMOVE REAR WHEEL


42. REMOVE REAR SPEED SENSOR


    C165811E01
  1. Disconnect the rear speed sensor connector.



    C165810E02
  1. Disconnect the grommet of the rear speed sensor wire from the hole in the wheel well.

  1. Remove the 2 bolts, No. 1 clamp and No. 2 clamp from the body and absorber.



    C165809
  1. Remove the bolt and rear speed sensor body from the carrier.

    NOTICE:
    Keep the sensor tip and rear speed sensor installation hole free from foreign matter.