Home › BODY › SLIDING ROOF › SLIDING ROOF SYSTEM

SLIDING ROOF SYSTEM > Sliding Roof does not Move by Operating Sliding Roof Control Switch

for Preparation Click here


DESCRIPTION

The sliding roof system uses a LIN communication protocol on the multiplex communication system. Inspect the communication system by following HOW TO PROCEED WITH TROUBLESHOOTING (Click here) to ensure that there are no problems with the multiplex communication system before troubleshooting the sliding roof system. The sliding roof system prohibits the AUTO UP function if the jam protection function malfunctions. Check that there are no DTCs output before troubleshooting the sliding roof system. If any sliding roof system DTCs are output, perform troubleshooting on the output DTCs first.

NOTICE:
When the sliding roof drive gear sub-assembly is reinstalled or replaced, the sliding roof drive gear sub-assembly must be initialized.


WIRING DIAGRAM


B174032E05


INSPECTION PROCEDURE

1.INSPECT FUSE (DC/DC, S/ROOF, ECU-IG NO. 1)
  1. Remove the DC/DC fuse from the engine room main relay block.

  1. Remove the S/ROOF and ECU-IG No. 1 fuses from the instrument panel junction block.

  1. Measure the resistance of the fuses.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    DC/DC fuse
    Always
    Below 1 Ω
    S/ROOF fuse
    Always
    Below 1 Ω
    ECU-IG No.1 fuse
    Always
    Below 1 Ω



NG
REPLACE FUSE
OK


2.CHECK WIRE HARNESS (SLIDING ROOF CONTROL ECU - BATTERY AND BODY GROUND)


    B130117E16
  1. Disconnect the Q12 connector.

  1. Measure the voltage and resistance according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Condition
    Specified Condition
    Q12-1 (B) - Body ground
    Always
    10 to 14 V
    Q12-5 (IG) - Body ground
    Power switch on (IG)
    10 to 14 V
    Q12-5 (IG) - Body ground
    Power switch off
    Below 1 V

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    Q12-2 (E) - Body ground
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3.PERFORM ACTIVE TEST BY TECHSTREAM (SLIDING ROOF OPERATION)
  1. Select the Active Test, use the Techstream to generate a control command, and then check that the sliding roof slides open/close and tilts up/down (Click here).

    Slide Roof: 
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Slide Roof
    Operate sliding roof SLIDE CLOSE/TILT UP
    Clos/Up: Sliding roof SLIDE CLOSE or TILT UP operation occurs.
    OFF: Sliding roof is not operating.
    -
    Slide Roof
    Operate sliding roof SLIDE OPEN/TILT DOWN
    Opn/Dwn: Sliding roof SLIDE OPEN or TILT DOWN operation occurs.
    OFF: Sliding roof is not operating.
    -

    OK:
    Sliding roof operates normally.



NG
REPLACE SLIDING ROOF DRIVE GEAR SUB-ASSEMBLY (SLIDING ROOF CONTROL ECU)
OK


4.READ VALUE USING TECHSTREAM (SLIDING ROOF CONTROL ECU)
  1. Use the Data List to check if the sliding roof switch assembly is functioning properly (Click here).

    Slide Roof: 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Hall IC1 Pulse
    Sliding roof operation signal/LO or HI
    LO: Sliding roof motor is not operating.
    HI: Sliding roof motor is operating.
    -
    Hall IC1 Status
    Sliding roof operation signal/NORMAL or LOCK
    NORMAL: Sliding roof motor is operating.
    LOCK: Sliding roof motor is not operating.
    -
    Hall IC2 Pulse
    Sliding roof operation signal/LO or HI
    LO: Sliding roof motor is not operating.
    HI: Sliding roof motor is operating.
    -
    Hall IC2 Status
    Sliding roof operation signal/NORMAL or LOCK
    NORMAL: Sliding roof motor is operating.
    LOCK: Sliding roof motor is not operating.
    -



NG
REPLACE SLIDING ROOF DRIVE GEAR SUB-ASSEMBLY (SLIDING ROOF CONTROL ECU)
OK


5.READ VALUE USING TECHSTREAM (SLIDING ROOF SWITCH ASSEMBLY)
  1. Use the Data List to check if the sliding roof switch assembly is functioning properly (Click here).

    Slide Roof: 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Open Switch
    Slide switch open signal/ON or OFF
    ON: OPEN switch is pressed.
    OFF: OPEN switch is not pressed.
    -
    Close Switch
    Slide switch close signal/ON or OFF
    ON: CLOSE switch is pressed.
    OFF: CLOSE switch is not pressed.
    -
    Up Switch
    Tilt switch up signal/ON or OFF
    ON: UP switch is pressed.
    OFF: UP switch is not pressed.
    -
    Down Switch
    Tilt switch down signal/ON or OFF
    ON: DOWN switch is pressed.
    OFF: DOWN switch is not pressed.
    -

    OK:
    The Techstream displays as shown in the table according to the operation of each switch.



NG
Go to step 6
OK

REPLACE SLIDING ROOF DRIVE GEAR SUB-ASSEMBLY (SLIDING ROOF CONTROL ECU)  

6.INSPECT ROOF CONSOLE BOX ASSEMBLY (SLIDING ROOF SWITCH ASSEMBLY)


    B174030E02
  1. Remove the roof console box assembly.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    Q1-3 (CLS) - Q1-2 (GND)
    CLOSE
    Below 100 Ω
    Q1-4 (OPN) - Q1-2 (GND)
    OPEN
    Below 100 Ω
    Q1-5 (DOWN) - Q1-2 (GND)
    DOWN
    Below 100 Ω
    Q1-6 (UP) - Q1-2 (GND)
    UP
    Below 100 Ω
    Q1-3 (CLS) - Q1-2 (GND)
    OPEN
    1 kΩ or higher
    Q1-4 (OPN) - Q1-2 (GND)
    CLOSE
    1 kΩ or higher
    Q1-5 (DOWN) - Q1-2 (GND)
    UP
    1 kΩ or higher
    Q1-6 (UP) - Q1-2 (GND)
    DOWN
    1 kΩ or higher



NG
REPLACE ROOF CONSOLE BOX ASSEMBLY (SLIDING ROOF SWITCH ASSEMBLY)
OK


7.CHECK WIRE HARNESS (SLIDING ROOF CONTROL ECU - ROOF CONSOLE BOX ASSEMBLY)


    B174031E02
  1. Remove the Q12 and Q1 connectors.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    Q12-2 (E) - Q1-2 (GND)
    Always
    Below 1 Ω
    Q12-7 (OPN) - Q1-4 (OPN)
    Always
    Below 1 Ω
    Q12-8 (DWN) - Q1-5 (DOWN)
    Always
    Below 1 Ω
    Q12-9 (CLS) - Q1-3 (CLS)
    Always
    Below 1 Ω
    Q12-10 (UP) - Q1-6 (UP)
    Always
    Below 1 Ω
    Q1-3 (CLS) - Body ground
    Always
    10 kΩ or higher
    Q1-4 (OPN) - Body ground
    Always
    10 kΩ or higher
    Q1-2 (GND) - Body ground
    Always
    Below 1 Ω
    Q1-5 (DOWN) - Body ground
    Always
    10 kΩ or higher
    Q1-6 (UP) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE SLIDING ROOF DRIVE GEAR SUB-ASSEMBLY (SLIDING ROOF CONTROL ECU)