Home › HYBRID SYSTEM · P310 › HYBRID VEHICLE CONTROL › HYBRID CONTROL SYSTEM

DTC    P0560-117    System Voltage

for Preparation Click here


DESCRIPTION

Battery power is constantly supplied to the BATT terminal of the hybrid vehicle control ECU to allow DTCs and freeze frame data to be retained in memory even though the power switch is turned off. The back-up power is supplied even when the power switch is off.

DTC No.
INF Code
DTC Detection Condition
Trouble Area
P0560
117
Malfunction in the hybrid vehicle control ECU back-up power source circuit
  1. Wire harness or connector
  2. Hybrid vehicle control ECU
  3. EFI No. 1 fuse

MONITOR DESCRIPTION

If a period of time has elapsed with a low voltage at the BATT terminal of the hybrid vehicle control ECU, the hybrid vehicle control ECU will determine that a malfunction has occurred in the back-up power supply system, and it will set a DTC. The MIL will illuminate the next time the engine is started.

MONITOR STRATEGY


Related DTCs
P0560 (INF 117): BATT signal malfunction
Required sensors / components
Main: Back-up power source circuit
Sub: Hybrid vehicle control ECU
Frequency of operation
Continuous
Duration
TMC's intellectual property
MIL operation
Immediately
Sequence of operation
None

TYPICAL ENABLING CONDITIONS


The monitor will run whenever the following DTCs are not present
TMC's intellectual property
Other conditions belong to TMC's intellectual property
-

TYPICAL MALFUNCTION THRESHOLDS


TMC's intellectual property
-

COMPONENT OPERATING RANGE


Auxiliary battery voltage
Between 9 and 14 V

WIRING DIAGRAM


A175409E03


INSPECTION PROCEDURE

1.CHECK CONNECTOR CONNECTION CONDITION (HYBRID VEHICLE CONTROL ECU CONNECTOR)


    A174883E01
  1. Check the connections of all hybrid vehicle control ECU connectors.

    OK:
    The connectors are connected securely and there are no contact problems.



NG
CONNECT SECURELY
OK


2.CHECK FUSE (EFI NO. 1 FUSE)


    A174422E01
  1. Remove the EFI No. 1 fuse from the engine room relay block.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance (Check for open):
    Tester Connection
    Switch Condition
    Specified Condition
    EFI No. 1 fuse
    Always
    Below 1 Ω

  1. Reinstall the EFI No. 1 fuse.



NG
REPLACE FUSE (EFI NO. 1 FUSE)
OK


3.CHECK HYBRID VEHICLE CONTROL ECU (BATT VOLTAGE)


    A173947E03
  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    D35-1 (BATT) - B3-5 (E1)
    Power switch off
    11 to 14 V



NG
Go to step 5
OK


4.CHECK DTC OUTPUT (HV)

HINT:
If DTC P0560-117 is output again after performing the inspection, replace the hybrid vehicle control ECU. If the DTC is not output, there may be a malfunction in the wire harness or connector. Perform a check for intermittent problems.

  1. Connect Techstream to the DLC3.

  1. Turn the power switch on (IG).

  1. Select the following menu items: Powertrain / Hybrid Control / Trouble Codes.

  1. Check output DTC.

Result:
Result
Proceed to
DTC P0560-177 is not output.
A
DTC P0560-177 is output again.
B



B
CHECK FOR INTERMITTENT PROBLEMS (Click here)
A

REPLACE HYBRID VEHICLE CONTROL ECU (Click here)  

5.CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU - EFI NO. 1 FUSE)


    A175410E02
  1. Check the harness and the connector between the EFI No. 1 fuse and hybrid vehicle control ECU.

    1. Remove the EFI No. 1 fuse from the engine room relay block.

    2. Disconnect connector D35 from the hybrid vehicle control ECU.

    3. Measure the resistance according to the value(s) in the table below.

      Standard resistance (Check for open):
      Tester Connection
      Condition
      Specified Condition
      EFI No. 1 fuse (2) - D35-1 (BATT)
      Always
      Below 1 Ω

      Standard resistance (Check for short):
      Tester Connection
      Switch Condition
      Specified Condition
      EFI No. 1 fuse (2) or D35-1 (BATT) - Body ground
      Always
      10 kΩ or higher

    4. Reconnect the hybrid vehicle control ECU connector.

    5. Reinstall the EFI No. 1 fuse.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (HYBRID VEHICLE CONTROL ECU - EFI NO. 1 FUSE)
OK

CHECK AND REPLACE ENGINE ROOM RELAY BLOCK