Home › HYBRID SYSTEM · P310 › HYBRID VEHICLE CONTROL › HYBRID CONTROL SYSTEM

DTC    P2122-104    Throttle / Pedal Position Sensor / Switch "D" Circuit Low Input

DTC    P2123-105    Throttle / Pedal Position Sensor / Switch "D" Circuit High Input

DTC    P2127-107    Throttle / Pedal Position Sensor / Switch "E" Circuit Low Input

DTC    P2128-108    Throttle / Pedal Position Sensor / Switch "E" Circuit High Input

for Preparation Click here


DESCRIPTION

Refer to the description for DTC P2120-111 .

DTC No.
INF Code
DTC Detection Condition
Trouble Area
P2122
104
Open or GND short in main sensor circuit
  1. Wire harness or connector
  2. Accelerator pedal assembly
  3. Hybrid vehicle control ECU
P2123
105
VC short in main sensor circuit
P2127
107
Open or GND short in sub sensor circuit
P2128
108
VC short in sub sensor circuit

WIRING DIAGRAM

Refer to the wiring diagram for DTC P2120-111 .

INSPECTION PROCEDURE

1.READ VALUE USING TECHSTREAM (ACCEL PEDAL POS #1, #2)


    FI07052
  1. Connect the Techstream to the DLC3.

  1. Turn the power switch on (IG).

  1. Select the following menu items: Powertrain / Hybrid Control / Data List / Accel Pedal Pos #1 and Accel Pedal Pos #2.

  1. Read the data list.

    HINT:
    5 V is described as 100% on the tester.

    Result:
    Pedal Condition
    Accel Pedal Pos #1
    Accel Pedal Pos #2
    Not depressed
    (8 to 28%) 0.4 to 1.4 V
    (20 to 44%) 1.0 to 2.2 V
    Fully depressed
    (62 to 92%) 3.1 to 4.6 V
    (78 to 100%) 3.9 to 5.0 V
    Not depressed
    → Fully depressed
    → Not depressed (Accelerator pedal should be operated slowly)
    Value changes progressively
    Value changes progressively



NG
Go to step 2
OK

CHECK FOR INTERMITTENT PROBLEMS (Click here)  

2.CHECK HYBRID VEHICLE CONTROL ECU
  1. Disconnect the accelerator pedal position sensor connector.

  1. Turn the power switch on (IG).



    A174222E21
  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    A43-24 (VCP1) - A43-33 (EP1)
    Power switch on (IG)
    4.5 to 5.5 V
    A43-31 (VCP2) - A43-32 (EP2)
    Power switch on (IG)
    4.5 to 5.5 V



NG
REPLACE HYBRID VEHICLE CONTROL ECU (Click here)
OK


3.CHECK HYBRID VEHICLE CONTROL ECU
  1. Connect the accelerator pedal position sensor connector.

  1. Turn the power switch on (IG).



    A174222E22
  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Condition
    Specified Condition
    A43-25 (VPA) - A43-33 (EP1)
    Power switch on (IG)
    Accelerator pedal released
    0.4 to 1.4 V
    Power switch on (IG)
    Accelerator pedal depressed
    3.1 to 4.6 V
    A43-26 (VPA2) - A43-32 (EP2)
    Power switch on (IG)
    Accelerator pedal released
    1.0 to 2.2 V
    Power switch on (IG)
    Accelerator pedal depressed
    3.9 to 5.5 V



NG
Go to step 4
OK

REPLACE HYBRID VEHICLE CONTROL ECU (Click here)  

4.CHECK HARNESS AND CONNECTOR (HV CONTROL ECU - ACCELERATOR PEDAL POSITION SENSOR)
  1. Turn the power switch off.

  1. Disconnect connector A43 from the hybrid vehicle control ECU.

  1. Disconnect the accelerator pedal position sensor connector.

  1. Turn the power switch on (IG).



    A175411E02
  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    A43-25 (VPA) - Body ground
    Power switch on (IG)
    Below 1 V
    A43-24 (VCP1) - Body ground
    Power switch on (IG)
    Below 1 V
    A43-33 (EP1) - Body ground
    Power switch on (IG)
    Below 1 V
    A43-26 (VPA2) - Body ground
    Power switch on (IG)
    Below 1 V
    A43-31 (VCP2) - Body ground
    Power switch on (IG)
    Below 1 V
    A43-32 (EP2) - Body ground
    Power switch on (IG)
    Below 1 V

  1. Turn the power switch off.

  1. Measure the resistance according to the value(s) in the table.

    Standard resistance (Check for open):
    Tester Connection
    Switch Condition
    Specified Condition
    A43-25 (VPA) - A18-6 (VPA1)
    Power switch off
    Below 1 Ω
    A43-24 (VCP1) - A18-4 (VCP1)
    Power switch off
    Below 1 Ω
    A43-33 (EP1) - A18-5 (EP1)
    Power switch off
    Below 1 Ω
    A43-26 (VPA2) - A18-3 (VPA2)
    Power switch off
    Below 1 Ω
    A43-31 (VCP2) - A18-1 (VCP2)
    Power switch off
    Below 1 Ω
    A43-32 (EP2) - A18-2 (EP2)
    Power switch off
    Below 1 Ω

    Standard resistance (Check for short):
    Tester Connection
    Switch Condition
    Specified Condition
    A43-25 (VPA) or A18-6 (VPA1) - Body ground and other terminals
    Power switch off
    10 kΩ or higher
    A43-24 (VCP1) or A18-4 (VCP1) - Body ground and other terminals
    Power switch off
    10 kΩ or higher
    A43-33 (EP1) or A18-5 (EP1) - Body ground and other terminals
    Power switch off
    10 kΩ or higher
    A43-26 (VPA2) or A18-3 (VPA2) - Body ground and other terminals
    Power switch off
    10 kΩ or higher
    A43-31 (VCP2) or A18-1 (VCP2) - Body ground and other terminals
    Power switch off
    10 kΩ or higher
    A43-32 (EP2) or A18-2 (EP2) - Body ground and other terminals
    Power switch off
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE ACCELERATOR PEDAL ASSEMBLY (Click here)