Home › Power Source / Network › NETWORKING › LIN COMMUNICATION SYSTEM
RM3160E _57 Power Source / Network _019704 NETWORKING _0095459 LIN COMMUNICATION SYSTEM U

NETWORKING  LIN COMMUNICATION SYSTEM  TERMINALS OF ECU  


CHECK MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) AND INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY


B357833C05
4.99,3.521 5.396,3.792 0.406,0.271 1.427,4.823 1.833,5.094 0.406,0.271 4.083,4.802 4.49,5.073 0.406,0.271 5.573,4.927 5.979,5.198 0.406,0.271 1.354,6.396 1.76,6.667 0.406,0.271 4.865,6.396 5.271,6.667 0.406,0.271 6.469,4.927 6.875,5.198 0.406,0.271 3.458,7.969 3.865,8.24 0.406,0.271 1.792,3.521 2.198,3.792 0.406,0.271 2.25,0.25 2.083,0.25 2.083,0.25 2.083,0.604 false 2.5,2.083 2.25,2.083 2.25,2.083 2.167,2.083 false 2.5,1.583 2.25,1.583 2.25,1.583 2.167,1.583 false 2.021,1.583 1.667,1.583 1.667,1.583 1.667,2.417 false 2.021,2.083 1.75,2.083 1.75,2.083 1.667,2.083 false 4.833,0.198 4.667,0.198 4.667,0.198 4.667,0.552 false 0.125,0.094 0.5,0.333 0.375,0.24 12 false *A 0.552,1.052 0.75,1.25 0.198,0.198 10 false 4H 0.552,1.802 0.75,2 0.198,0.198 10 false 4F 0.563,2.24 0.76,2.438 0.198,0.198 10 false 4K 0.833,2.5 1.031,2.698 0.198,0.198 10 false 4L 2.365,0.156 2.563,0.354 0.198,0.198 10 false *1 2.563,1.479 2.875,1.688 0.313,0.208 10 false F19 2.573,1.969 2.927,2.198 0.354,0.229 10 false F18 1.604,2.448 1.802,2.646 0.198,0.198 10 false *a 4.917,0.083 5.167,0.25 0.25,0.167 10 false MB 6.458,0.906 6.656,1.104 0.198,0.198 10 false 4D 6.458,1.74 6.656,1.938 0.198,0.198 10 false 4A 1.885,3.573 2.208,3.781 0.323,0.208 10 false F18 5.083,3.573 5.448,3.781 0.365,0.208 10 false F19 1.552,4.865 1.75,5.063 0.198,0.198 10 false 4H 4.208,4.865 4.406,5.063 0.198,0.198 10 false 4F 5.698,4.969 5.896,5.167 0.198,0.198 10 false 4K 1.479,6.458 1.74,6.667 0.26,0.208 10 false 4D 4.99,6.448 5.188,6.646 0.198,0.198 10 false 4A 6.604,4.969 6.802,5.167 0.198,0.198 10 false 4L 3.563,8.021 3.844,8.271 0.281,0.25 10 false MB
*A Main Body ECU (Multiplex Network Body ECU) with 2 Connectors - -
*1 Main Body ECU (Multiplex Network Body ECU) - -
*a 2 connectors - -


B357834C05
1.083,3.479 1.5,3.75 0.417,0.271 3.594,3.5 4.01,3.771 0.417,0.271 5.917,3.479 6.333,3.75 0.417,0.271 1.417,4.833 1.833,5.104 0.417,0.271 4.042,4.833 4.458,5.104 0.417,0.271 5.563,4.906 5.979,5.177 0.417,0.271 1.385,6.396 1.802,6.667 0.417,0.271 4.844,6.396 5.26,6.667 0.417,0.271 6.438,4.906 6.854,5.177 0.417,0.271 3.417,7.958 3.833,8.229 0.417,0.271 2.083,0.604 2.083,0.25 2.083,0.25 2.25,0.25 false 2.167,1.083 2.583,1.083 false 2.167,1.583 2.583,1.583 false 2.167,2.083 2.583,2.083 false 1.667,1.583 2.021,1.583 false 1.667,2.083 2.021,2.083 false 1.667,2.5 1.667,1.083 1.667,1.083 2.021,1.083 false 4.583,0.552 4.583,0.198 4.583,0.198 4.75,0.198 false 0.156,0.135 0.531,0.375 0.375,0.24 12 false *A 0.552,1.052 0.833,1.219 0.281,0.167 10 false 4H 0.552,1.823 0.833,1.99 0.281,0.167 10 false 4F 0.563,2.25 0.844,2.417 0.281,0.167 10 false 4K 0.833,2.5 1.115,2.667 0.281,0.167 10 false 4L 2.302,0.188 2.615,0.385 0.313,0.198 10 false *1 1.594,2.531 1.906,2.729 0.313,0.198 10 false *a 2.646,1.01 2.927,1.177 0.281,0.167 10 false F20 2.656,1.51 2.938,1.677 0.281,0.167 10 false F19 2.656,2.01 2.938,2.177 0.281,0.167 10 false F18 4.813,0.125 5.156,0.344 0.344,0.219 10 false MB 6.458,0.927 6.823,1.094 0.365,0.167 10 false 4D 6.458,1.75 6.823,1.917 0.365,0.167 10 false 4A 1.177,3.542 1.521,3.729 0.344,0.188 10 false F18 3.688,3.563 3.969,3.729 0.281,0.167 10 false F19 6.01,3.531 6.333,3.708 0.323,0.177 10 false F20 1.531,4.896 1.813,5.063 0.281,0.167 10 false 4H 4.177,4.896 4.458,5.063 0.281,0.167 10 false 4F 5.688,4.958 5.969,5.125 0.281,0.167 10 false 4K 3.521,8.021 3.885,8.25 0.365,0.229 10 false MB 1.521,6.458 1.802,6.625 0.281,0.167 10 false 4D 4.969,6.458 5.25,6.625 0.281,0.167 10 false 4A 6.573,4.948 6.854,5.115 0.281,0.167 10 false 4L
*A Main Body ECU (Multiplex Network Body ECU) with 3 Connectors - -
*1 Main Body ECU (Multiplex Network Body ECU) - -
*a 3 connectors - -


a.

Remove the main body ECU (multiplex network body ECU) from the instrument panel junction block assembly.

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL


b.

Reconnect the instrument panel junction block assembly connectors.


c.

Measure the resistance and voltage according to the value(s) in the table below.

HINT:

Measure the values on the wire harness side with the connector disconnected.


Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
MB-11 (GND1) - Body ground - Ground Always Below 1 Ω
MB-31 (BECU) - Body ground - Battery power supply Always 11 to 14 V
MB-30 (ACC) - Body ground - ACC power supply Ignition switch ACC 11 to 14 V
MB-30 (ACC) - Body ground - ACC power supply Ignition switch off Below 1 V
MB-32 (IG) - Body ground - IG power supply Ignition switch ON 11 to 14 V
MB-32 (IG) - Body ground - IG power supply Ignition switch off Below 1 V


d.

Install the main body ECU (multiplex network body ECU) to instrument panel junction block assembly.

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>INSTALLATION


e.

Check for pulses according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
4D-25 - Body ground P - Body ground LIN communication line Ignition switch ON Pulse generation
4H-35 - Body ground P - Body ground LIN communication line Ignition switch ON Pulse generation



CHECK POWER WINDOW REGULATOR MOTOR ASSEMBLY (for Driver Door)


B286202
2.115,0.552 2.49,0.781 0.375,0.229 2.115,0.885 2.49,1.115 0.375,0.229 2.26,0.583 2.531,0.74 0.271,0.156 10 false I4 2.229,0.917 2.5,1.073 0.271,0.156 10 false H4 2.552,0.583 2.823,0.781 0.271,0.198 10 false *A 2.552,0.927 2.844,1.146 0.292,0.219 10 false *B
*A for LHD *B for RHD


a.

Disconnect the I4*1 or H4*2 power window regulator motor assembly (for driver door) connector.

*1: for LHD

*2: for RHD



b.

Measure the resistance and voltage according to the value(s) in the table below.

HINT:

Measure the values on the wire harness side with the connector disconnected.


for LHD
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
I4-2 (B) - Body ground L - Body ground Battery power supply Always 11 to 14 V
I4-1 (GND) - Body ground W-B - Body ground Ground Always Below 1 Ω

for RHD
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
H4-2 (B) - Body ground L - Body ground Battery power supply Always 11 to 14 V
H4-1 (GND) - Body ground W-B - Body ground Ground Always Below 1 Ω


c.

Reconnect the I4*1 or H4*2 power window regulator motor assembly (for driver door) connector.

*1: for LHD

*2: for RHD



d.

Check for pulses according to the value(s) in the table below.

for LHD
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
I4-9 (LIN) - Body ground G - Body ground LIN communication line Ignition switch ON Pulse generation

for RHD
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
H4-9 (LIN) - Body ground G - Body ground LIN communication line Ignition switch ON Pulse generation

If the result is not as specified, the power window regulator motor assembly (for driver door) may be malfunctioning.



CHECK POWER WINDOW REGULATOR MOTOR ASSEMBLY (for Front Passenger Door)


B286202
2.021,0.51 2.396,0.74 0.375,0.229 2.021,0.833 2.396,1.063 0.375,0.229 2.135,0.542 2.406,0.698 0.271,0.156 10 false H5 2.167,0.875 2.531,1.177 0.365,0.302 10 false I5 2.458,0.542 2.729,0.698 0.271,0.156 10 false *A 2.458,0.865 2.729,1.021 0.271,0.156 10 false *B
*A for LHD *B for RHD


a.

Disconnect the H5*1 or I5*2 power window regulator motor assembly (for front passenger door) connector.

*1: for LHD

*2: for RHD



b.

Measure the resistance and voltage according to the value(s) in the table below.

HINT:

Measure the values on the wire harness side with the connector disconnected.


for LHD
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
H5-2 (B) - Body ground L - Body ground Battery power supply Always 11 to 14 V
H5-1 (GND) - Body ground W-B - Body ground Ground Always Below 1 Ω

for RHD
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
I5-2 (B) - Body ground L - Body ground Battery power supply Always 11 to 14 V
I5-1 (GND) - Body ground W-B - Body ground Ground Always Below 1 Ω


c.

Reconnect the H5*1 or I5*2 power window regulator motor assembly (for front passenger door) connector.

*1: for LHD

*2: for RHD



d.

Check for pulses according to the value(s) in the table below.

for LHD
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
H5-9 (LIN) - Body ground P - Body ground LIN communication line Ignition switch ON Pulse generation

for RHD
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
I5-9 (LIN) - Body ground P - Body ground LIN communication line Ignition switch ON Pulse generation



CHECK POWER WINDOW REGULATOR MOTOR ASSEMBLY (for Rear RH Door)


B203471
2.302,0.781 2.646,0.99 0.344,0.208 2.406,0.802 2.74,0.99 0.333,0.188 10 false J2

a.

Disconnect the J2 power window regulator motor assembly (for rear RH door) connector.


b.

Measure the resistance and voltage according to the value(s) in the table below.

HINT:

Measure the values on the wire harness side with the connector disconnected.


Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
J2-2 (B) - Body ground LA-B - Body ground Battery power supply Always 11 to 14 V
J2-1 (GND) - Body ground W-B - Body ground Ground Always Below 1 Ω


c.

Reconnect the J2 power window regulator motor assembly (for rear RH door) connector.


d.

Check for pulses according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
J2-9 (LIN) - Body ground P - Body ground LIN communication line Ignition switch ON Pulse generation



CHECK POWER WINDOW REGULATOR MOTOR ASSEMBLY (for Rear LH Door)


B203471
2.292,0.781 2.635,0.99 0.344,0.208 2.385,0.813 2.667,1 0.281,0.188 10 false K2

a.

Disconnect the K2 power window regulator motor assembly (for rear LH door) connector.


b.

Measure the resistance and voltage according to the value(s) in the table below.

HINT:

Measure the values on the wire harness side with the connector disconnected.


Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
K2-2 (B) - Body ground LA-G - Body ground Battery power supply Always 11 to 14 V
K2-1 (GND) - Body ground W-B - Body ground Ground Always Below 1 Ω


c.

Reconnect the K2 power window regulator motor assembly (for rear LH door) connector.


d.

Check for pulses according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
K2-9 (LIN) - Body ground P - Body ground LIN communication line Ignition switch ON Pulse generation



CHECK POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY (for Models with Jam Protection Function on 4 Windows)


B131578
3.01,0.271 3.354,0.49 0.344,0.219 3.781,0.271 4.125,0.49 0.344,0.219 3.875,0.302 4.188,0.49 0.313,0.188 10 false H7 3.135,0.302 3.448,0.49 0.313,0.188 10 false I7 3.406,0.313 3.719,0.5 0.313,0.188 10 false *A 4.177,0.313 4.49,0.5 0.313,0.188 10 false *B
*A for LHD *B for RHD


a.

Disconnect the I7*1 or H7*2 power window regulator master switch assembly connector.

*1: for LHD

*2: for RHD



b.

Measure the resistance and voltage according to the value(s) in the table below.

HINT:

Measure the values on the wire harness side with the connector disconnected.


for LHD
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
I7-11 (B) - Body ground GR - Body ground Battery power supply Always 11 to 14 V
I7-12 (GND) - Body ground W-B - Body ground Ground Always Below 1 Ω

for RHD
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
H7-11 (B) - Body ground GR - Body ground Battery power supply Always 11 to 14 V
H7-12 (GND) - Body ground W-B - Body ground Ground Always Below 1 Ω


c.

Reconnect the I7*1 or H7*2 power window regulator master switch assembly connector.

*1: for LHD

*2: for RHD



d.

Check for pulses according to the value(s) in the table below.

for LHD
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
I7-17 (LIN1) - Body ground P - Body ground LIN communication line Ignition switch ON Pulse generation
I7-16 (LIN2) - Body ground G - Body ground LIN communication line Ignition switch ON Pulse generation

for RHD
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
H7-17 (LIN1) - Body ground P - Body ground LIN communication line Ignition switch ON Pulse generation
H7-16 (LIN2) - Body ground G - Body ground LIN communication line Ignition switch ON Pulse generation



CHECK POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY (for Models with Jam Protection Function on 2 Windows)


B164269
3.385,0.104 3.802,0.323 0.417,0.219 3.521,0.135 3.979,0.333 0.458,0.198 10 false H6

a.

Disconnect the H6 power window regulator master switch assembly connector.


b.

Measure the resistance and voltage according to the value(s) in the table below.

HINT:

Measure the values on the wire harness side with the connector disconnected.


Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
H6-3 (B) - Body ground GR - Body ground Battery power supply Always 11 to 14 V
H6-1 (GND) - Body ground W-B - Body ground Ground Always Below 1 Ω


c.

Reconnect the H6 power window regulator master switch assembly connector.


d.

Check for pulses according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
H6-6 (LIN1) - Body ground P - Body ground LIN communication line Ignition switch ON Pulse generation
H6-7 (LIN2) - Body ground G - Body ground LIN communication line Ignition switch ON Pulse generation



CHECK SLIDING ROOF ECU (SLIDING ROOF DRIVE GEAR SUB-ASSEMBLY) (w/ Sliding Roof System)


B270994
3.406,0.208 3.76,0.427 0.354,0.219 3.51,0.24 3.771,0.521 0.26,0.281 10 false S5

a.

Disconnect the S5 sliding roof ECU (sliding roof drive gear sub-assembly) connector.


b.

Measure the resistance and voltage according to the value(s) in the table below.

HINT:

Measure the values on the wire harness side with the connector disconnected.


Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
S5-8 (B) - Body ground L - Body ground Battery power supply Always 11 to 14 V
S5-12 (E) - Body ground W-B - Body ground Ground Always Below 1 Ω


c.

Reconnect the S5 sliding roof ECU (sliding roof drive gear sub-assembly) connector.


d.

Check for pulses according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
S5-11 (MPX1) - Body ground B - Body ground LIN communication line Ignition switch ON Pulse generation



CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) (w/ Smart Entry and Start System)


B340022
4.99,0.292 5.396,0.542 0.406,0.25 1.552,0.292 1.979,0.521 0.427,0.229 3.24,0.292 3.667,0.521 0.427,0.229 1.656,0.323 2.115,0.521 0.458,0.198 10 false F10 3.354,0.333 3.813,0.531 0.458,0.198 10 false F12 5.094,0.333 5.552,0.531 0.458,0.198 10 false F13

a.

Disconnect the F13 certification ECU (smart key ECU assembly) connector.


b.

Measure the resistance and voltage according to the value(s) in the table below.

HINT:

Measure the values on the wire harness side with the connector disconnected.


Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
F13-11 (E) - Body ground W-B - Body ground Ground Always Below 1 Ω
F13-10 (+B) - Body ground GR - Body ground +B power supply Always 11 to 14 V


c.

Reconnect the F13 certification ECU (smart key ECU assembly) connector.


d.

Check for pulses according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
F13-6 (LIN) - Body ground SB - Body ground LIN communication line Ignition switch ON Pulse generation



CHECK STEERING LOCK ECU (STEERING LOCK ACTUATOR ASSEMBLY) (w/ Smart Entry and Start System)


B118684
3.469,0.302 3.823,0.521 0.354,0.219 3.542,0.333 3.958,0.708 0.417,0.375 10 false F54

a.

Disconnect the F54 steering lock ECU (steering lock actuator assembly) connector.


b.

Measure the resistance and voltage according to the value(s) in the table below.

HINT:

Measure the values on the wire harness side with the connector disconnected.


Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
F54-1 (GND) - Body ground W-B Body ground Ground Always Below 1 Ω
F54-7 (B) - Body ground B - Body ground Battery power supply Always 11 to 14 V


c.

Reconnect the F54 steering lock ECU (steering lock actuator assembly) connector.


d.

Check for pulses according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
F54-5 (LIN) - Body ground SB - Body ground LIN communication line Ignition switch ON Pulse generation



CHECK ID CODE BOX (IMMOBILISER CODE ECU) (w/ Smart Entry and Start System) (for LHD)


B278917
3.396,0.167 3.792,0.396 0.396,0.229 3.479,0.198 3.76,0.354 0.281,0.156 10 false F67

a.

Disconnect the F67 ID code box (immobiliser code ECU) connector.


b.

Measure the resistance and voltage according to the value(s) in the table below.

HINT:

Measure the values on the wire harness side with the connector disconnected.


Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
F67-5 (GND) - Body ground BR - Body ground Ground Always Below 1 Ω
F67-1 (+B) - Body ground Y - Body ground +B power supply Always 11 to 14 V


c.

Reconnect the F67 ID code box (immobiliser code ECU) connector.


d.

Check for pulses according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
F67-2 (LIN1) - Body ground SB - Body ground LIN communication line Ignition switch ON Pulse generation