Home › Power Source / Network › NETWORKING › LIN COMMUNICATION SYSTEM
RM3160E _57 Power Source / Network _019704 NETWORKING _0095459 LIN COMMUNICATION SYSTEM C

NETWORKING  LIN COMMUNICATION SYSTEM  B2324  Rear Door LH ECU Communication Stop  


DESCRIPTION

This DTC is stored when LIN communication between the power window regulator motor assembly (for rear LH door) and main body ECU (multiplex network body ECU) stops for 10 seconds or more.

DTC No. Detection Item DTC Detection Condition Trouble Area
B2324 Rear Door LH ECU Communication Stop No communication between power window regulator motor assembly (for rear LH door) and main body ECU (multiplex network body ECU) for 10 seconds or more.
·

Power window regulator motor assembly (for rear LH door)

·

Main body ECU (multiplex network body ECU)

·

Instrument panel junction block assembly

·

Wire harness or connector

·

P/W R/L fuse



WIRING DIAGRAM

B365180
1.479,0.917 1.802,1.135 0.323,0.219 10 false LIN2 1.865,0.781 2.104,1.063 0.24,0.281 10 false 16 3.135,0.771 3.375,1.052 0.24,0.281 10 false 35 4.563,0.76 4.76,0.958 0.198,0.198 10 false 9 4.781,0.938 5.073,1.146 0.292,0.208 10 false LIN 0.177,1.865 0.49,2.063 0.313,0.198 10 false MB 0.177,2.021 1.823,2.406 1.646,0.385 10 false Main Body ECU (Multiplex Network Body ECU) 1.906,1.594 2.219,1.792 0.313,0.198 10 false 4H 1.896,1.75 3.51,2.188 1.615,0.438 10 false Instrument Panel Junction Block Assembly 5.5,0.635 5.656,0.833 0.156,0.198 10 false B 5.313,1.458 5.656,1.688 0.344,0.229 10 false GND 5.729,0.521 5.885,0.719 0.156,0.198 10 false 2 5.719,1.344 5.875,1.542 0.156,0.198 10 false 1 6.188,0.781 6.771,1.104 0.583,0.323 10 false P/W R/L 4.24,1.75 4.552,1.948 0.313,0.198 10 false K2 4.24,1.927 6.188,2.333 1.948,0.406 10 false Power Window Regulator Motor Assembly (for Rear LH Door) 0.677,3.323 4.344,3.521 3.667,0.198 10 false : LIN Communication Line

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

When a power window regulator motor assembly is replaced or removed and reinstalled, it requires initialization.

Click hereVehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM(for Models with Jam Protection Function on 4 Windows)>INITIALIZATION

·

If the main body ECU (multiplex network body ECU) is replaced, refer to Service Bulletin.*

*: Smart Entry and Start System


·

As the door control battery is installed between the vehicle battery and main body ECU (multiplex network body ECU), first perform the inspections in On-Vehicle Inspection to confirm that there are no malfunctions in the power source circuit for the main body ECU (multiplex network body ECU) before performing this troubleshooting procedure.*

Click hereVehicle Interior>DOOR LOCK>POWER DOOR LOCK CONTROL SYSTEM>ON-VEHICLE INSPECTION

*: for LHD




PROCEDURE

1.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY
a.

Remove the instrument panel junction block assembly.

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL

B365183
1.854,0.729 2.26,0.958 0.406,0.229 5.448,0.479 5.854,0.708 0.406,0.229 1.792,1.896 2.01,1.438 false 0.271,0.135 0.583,0.333 0.313,0.198 10 false *a 1.958,0.76 2.271,0.958 0.313,0.198 10 false MB 5.573,0.51 5.885,0.708 0.313,0.198 10 false 4H 1.646,1.938 1.958,2.135 0.313,0.198 10 false LIN2
*a Component without harness connected
(Instrument Panel Junction Block Assembly)
- -



b.

Remove the main body ECU (multiplex network body ECU) from the instrument panel junction block assembly.


c.

Measure the resistance according to the value(s) in the table below.

HINT:

This inspection is to check the LIN communication line in the instrument panel junction block assembly that connects the wire harness to the built-in main body ECU (multiplex network body ECU).


Standard Resistance:
Tester Connection Condition Specified Condition
4H-35 - MB-16 (LIN2) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - POWER WINDOW REGULATOR MOTOR ASSEMBLY (for Rear LH Door))

NG

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

2.CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - POWER WINDOW REGULATOR MOTOR ASSEMBLY (for Rear LH Door))
a.

Disconnect the K2 power window regulator motor assembly (for rear LH door) connector.


b.

Measure the resistance according to the value(s) in the table below.

NOTICE:

Make sure that each ECU is in sleep mode before performing the inspection. To enter sleep mode, turn the ignition switch from ON to off and wait for 180 seconds or more without operating any switches.


Standard Resistance:
Tester Connection Condition Specified Condition
4H-35 - K2-9 (LIN) Ignition switch off Below 1 Ω
K2-9 (LIN) - Body ground Ignition switch off 10 kΩ or higher
4H-35 - Body ground Ignition switch off 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR MOTOR ASSEMBLY (for Rear LH Door) - BATTERY, BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR MOTOR ASSEMBLY (for Rear LH Door) - BATTERY, BODY GROUND)
a.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
K2-2 (B) - K2-1 (GND) Always 11 to 14 V



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
K2-1 (GND) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

4.REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY (for Rear LH Door)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY (for Rear LH Door)
a.

Replace the power window regulator motor assembly (for rear LH door).

Click hereVehicle Exterior>WINDOW / GLASS>POWER WINDOW REGULATOR MOTOR(for Rear Door)>REMOVAL


Result:
Proceed to
NEXT



NEXT

5.CHECK DTC OUTPUT
5.CHECK DTC OUTPUT
a.

Clear the DTCs.

Click herePower Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>DTC CHECK / CLEAR

Body Electrical > Main Body > Clear DTCs
50002 123

b.

Recheck for DTCs.

Body Electrical > Main Body > Trouble Codes
50001 123
OK:

DTC B2324 is not output.



Result:
Proceed to
OK
NG



OK

END (POWER WINDOW REGULATOR MOTOR ASSEMBLY (for Rear LH Door) WAS DEFECTIVE)

NG

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)