Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › SMART ENTRY AND START SYSTEM(for Start Function)
RM3160E _58 Vehicle Interior _019706 THEFT DETERRENT / KEYLESS ENTRY _0095461 SMART ENTRY AND START SYSTEM(for Start Function) C

THEFT DETERRENT / KEYLESS ENTRY  SMART ENTRY AND START SYSTEM(for Start Function)  B2274  ACC Monitor Malfunction  


DESCRIPTION

This DTC is stored when a malfunction in the ACC output circuit is detected. The ACC output circuit is the circuit that goes from the ACC output terminal of the certification ECU (smart key ECU assembly) to the ACC relay.

DTC No. Detection Item DTC Detection Condition Trouble Area Note
B2274 ACC Monitor Malfunction Malfunction in the ACC relay circuit in the certification ECU (smart key ECU assembly) or in the external circuit (1-trip detection logic*).
HINT:

When the voltage at terminal ACCD is not at the standard, the system is determined to be malfunctioning.


·

AM2 fuse

·

Instrument panel junction block assembly

·

Certification ECU (Smart key ECU assembly)

·

Wire harness or connector


DTC Output Confirmation Operation:

Wait 10 seconds after turning the engine switch on (ACC) or on (IG), and then wait another 10 seconds after turning the engine switch off.



*: Only detected while a malfunction is present.


Vehicle Condition and Fail-safe Function when Malfunction Detected
Vehicle Condition when Malfunction Detected Fail-safe Function when Malfunction Detected
·

If there is a malfunction due to the ACC relay being stuck on, the ACC relay does not turn off even though the engine switch is off.

·

If there is a malfunction due to the ACC relay being stuck off, the ACC relay does not turn on even though the engine switch is on (ACC).


HINT:

The engine switch can be turned on (IG) and the engine can be started.


-

Related Data List and Active Test Items
DTC No. Data List and Active Test
B2274
Power Source Control
·

ACC Relay Monitor


Starting Control
·

Ignition



WIRING DIAGRAM

B360711E01
0.146,1.073 1.083,1.271 0.938,0.198 10 false from Battery 1.604,1.229 1.958,1.458 0.354,0.229 10 false AM2 2.396,1.083 2.708,1.281 0.313,0.198 10 false F13 3.542,1.729 3.854,1.927 0.313,0.198 10 false F13 2.396,2.229 2.708,2.427 0.313,0.198 10 false F13 2.427,0.906 2.74,1.104 0.313,0.198 10 false 10 2.427,2.063 2.74,2.26 0.313,0.198 10 false 11 3.615,1.552 3.927,1.75 0.313,0.198 10 false 9 2.729,1.094 3.042,1.292 0.313,0.198 10 false +B 2.74,2.25 3.052,2.448 0.313,0.198 10 false E 3.063,1.729 3.5,1.969 0.438,0.24 10 false ACCD 2.344,2.896 3.896,3.281 1.552,0.385 10 false Certification ECU (Smart Key ECU Assembly) 4.271,1.323 4.583,1.521 0.313,0.198 10 false 4K 4.271,1.729 4.583,1.927 0.313,0.198 10 false 4A 4.313,1.135 4.469,1.333 0.156,0.198 10 false 1 4.281,1.563 4.521,1.781 0.24,0.219 10 false 28 5.719,1.469 6.375,1.708 0.656,0.24 10 false ECU-ACC 5.24,2.052 5.698,2.25 0.458,0.198 10 false ACC 4.073,2.438 6.854,2.698 2.781,0.26 10 false Instrument Panel Junction Block Assembly 6.448,1.313 6.76,1.51 0.313,0.198 10 false 4A 6.438,1.729 6.75,1.927 0.313,0.198 10 false 4A 6.458,1.146 6.771,1.344 0.313,0.198 10 false 37 6.458,1.563 6.771,1.76 0.313,0.198 10 false 27

CAUTION / NOTICE / HINT

NOTICE:
·

When using the GTS with the engine switch off, connect the GTS to the DLC3 and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Entry&Start(CAN). While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.

·

The smart entry and start system (for Start Function) uses the LIN communication system and CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting. Troubleshoot the smart entry and start system (for Start Function) after confirming that the communication systems are functioning properly.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM(for Start Function)>HOW TO PROCEED WITH TROUBLESHOOTING

·

Inspect the fuses of circuits related to this system before performing the following procedure.

·

Before replacing the certification ECU (smart key ECU assembly), refer to the smart entry and start system (for Start Function) Precaution.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM(for Start Function)>PRECAUTION

·

After repair, confirm that no DTCs are output by performing "DTC Output Confirmation Operation".



HINT:

When the cable is disconnected and reconnected to the negative (-) battery terminal, the power source mode returns to the state it was in before the cable was disconnected.


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (POWER SOURCE)

OK

2.CHECK HARNESS AND CONNECTOR (GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR IN CIRCUIT CONNECTED TO POWER SOURCE

2.CHECK HARNESS AND CONNECTOR (GROUND)

OK

3.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)
a.

Disconnect the F13 certification ECU (smart key ECU assembly) connector.


b.

Disconnect the 4A instrument panel junction block assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F13-9 (ACCD) - 4A-28 Always Below 1 Ω
F13-9 (ACCD) or 4A-28- Body ground Always 10 kΩ or higher
4A-27 - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

4.CHECK INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY (ACC RELAY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY (ACC RELAY)
a.

Remove the instrument panel junction block assembly.

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL


b.

Measure the resistance according to the value(s) in the table below.

B360712C01
2.208,0.708 2.552,0.927 0.344,0.219 5.438,0.708 5.781,0.927 0.344,0.219 2.313,0.729 2.625,0.927 0.313,0.198 10 false 4A 5.531,0.74 5.844,0.938 0.313,0.198 10 false 4K 0.229,0.156 0.542,0.313 0.313,0.156 10 false *a
*a Component without harness connected
(Instrument Panel Junction Block Assembly)
- -


Standard Resistance:
Tester Connection Condition Specified Condition
4A-28 - 4A-27 20°C (68°F) 130.92 to 190.74 Ω
4K-1 - 4A-37 Battery voltage not applied to terminals 4A-28 and 4A-27 10 kΩ or higher
Battery voltage applied to terminals 4A-28 and 4A-27 Below 1 Ω



Result:
Proceed to
OK
NG



OK

5.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

5.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
a.
C277841C07
1.417,0.094 1.802,0.323 0.385,0.229 0.99,1.698 0.99,0.813 false 0.104,0.052 0.302,0.219 0.198,0.167 10 false *a 0.865,1.74 1.26,1.885 0.396,0.146 10 false ACCD 1.51,0.125 1.813,0.292 0.302,0.167 10 false F13
*a Component with harness connected
(Certification ECU (Smart Key ECU Assembly))


Reconnect the F13 certification ECU (smart key ECU assembly) connector.


b.

Install the instrument panel junction block assembly.

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>INSTALLATION


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
F13-9 (ACCD) - Body ground Engine switch off → Engine switch on (ACC) 1 V or less → 8.5 V or higher



Result:
Proceed to
OK
NG



OK

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)