Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM › 2013.12–2016.11
RM3160E _57 Power Source / Network _019704 NETWORKING _0095663 CAN COMMUNICATION SYSTEM J

NETWORKING  CAN COMMUNICATION SYSTEM  Check CAN Bus Line for Short to GND (LHD Models)  


DESCRIPTION

There may be a short circuit between one of the CAN bus lines and GND when there is no resistance between terminals 6 (CANH) and 4 (CG) or 14 (CANL) and 4 (CG) of the DLC3.

Symptom Trouble Area
No resistance exists between terminals 6 (CANH) and 4 (CG) or 14 (CANL) and 4 (CG) of DLC3.
·

Short in CAN main bus line

·

Short in CAN branch line

·

Combination meter assembly

·

Power steering ECU assembly

·

Main body ECU (multiplex network body ECU)

·

Steering sensor

·

Airbag sensor assembly

·

ECM

·

Skid control ECU (brake actuator assembly)

·

Air conditioning amplifier assembly

·

Network gateway ECU*1

·

4WD ECU assembly*2

·

Radio and display receiver assembly*3

·

Headlight leveling ECU assembly*4

·

Certification ECU (smart key ECU assembly)*5

·

No. 3 CAN junction connector

·

No. 4 CAN junction connector



·

*1: w/ Blind Spot Monitor System or Parking Assist Monitor System

·

*2: for AWD

·

*3: for Radio and Display Type

·

*4: w/ Automatic Headlight Beam Level Control System

·

*5: w/ Smart Entry and Start System


WIRING DIAGRAM

C295125
0.115,0.094 1.438,0.354 1.323,0.26 12 false V Bus: 5.625,0.156 6.969,0.354 1.344,0.198 10 false x: Suspected Area 4.99,1.104 6.052,1.406 1.063,0.302 10 false *: for AWD 1.854,0.771 2.271,0.979 0.417,0.208 10 false A43 2.781,1.021 3.229,1.219 0.448,0.198 10 false CANL 3.469,0.375 3.885,0.583 0.417,0.208 10 false 120 Ω 2.188,0.771 2.604,0.979 0.417,0.208 10 false ECM 1.083,6.521 1.531,6.719 0.448,0.198 10 false CANL 1.063,2.875 1.51,3.073 0.448,0.198 10 false CANL 5.844,3.823 6.292,4.021 0.448,0.198 10 false CANL 6.073,5.677 6.521,5.875 0.448,0.198 10 false CANL 1.063,4.74 1.51,4.938 0.448,0.198 10 false CANL 1.031,2.292 1.479,2.49 0.448,0.198 10 false CANH 1.052,4.146 1.5,4.344 0.448,0.198 10 false CANH 4.448,2.26 4.854,2.479 0.406,0.219 10 false F102 1.052,5.938 1.5,6.135 0.448,0.198 10 false CANH 5.833,3.24 6.281,3.438 0.448,0.198 10 false CANH 5.896,5.344 6.344,5.542 0.448,0.198 10 false CANH 4.104,1.01 4.552,1.208 0.448,0.198 10 false CANH 4.823,2.26 6.781,2.469 1.958,0.208 10 false No. 3 CAN Junction Connector 1.552,2.292 1.74,2.5 0.188,0.208 10 false 4 1.542,2.865 1.729,3.073 0.188,0.208 10 false 8 1.552,5.927 1.74,6.135 0.188,0.208 10 false 3 1.542,4.135 1.771,4.313 0.229,0.177 10 false 6 1.542,4.729 1.729,4.938 0.188,0.208 10 false 5 1.552,6.521 1.74,6.729 0.188,0.208 10 false 2 2.802,4.135 2.99,4.344 0.188,0.208 10 false 8 2.802,2.292 2.99,2.5 0.188,0.208 10 false 5 2.74,2.865 2.927,3.073 0.188,0.208 10 false 15 2.74,4.729 2.927,4.938 0.188,0.208 10 false 18 5.573,3.813 5.76,4.031 0.188,0.219 10 false 13 2.49,2.177 2.677,2.385 0.188,0.208 10 false P 2.802,5.927 2.99,6.135 0.188,0.208 10 false 4 2.74,6.531 2.927,6.74 0.188,0.208 10 false 14 1.969,5.833 2.292,6.094 0.323,0.26 10 false BE 1.854,2.948 2.042,3.156 0.188,0.208 10 false B 1.979,4.833 2.167,5.042 0.188,0.208 10 false W 2.031,4.042 2.219,4.25 0.188,0.208 10 false L 1.979,6.604 2.167,6.813 0.188,0.208 10 false W 2.99,1.646 3.177,1.854 0.188,0.208 10 false W 5.208,5.146 5.396,5.354 0.188,0.208 10 false V 5.188,5.927 5.375,6.135 0.188,0.208 10 false W 4.167,1.646 4.354,1.854 0.188,0.208 10 false B 4.083,1.281 4.354,1.5 0.271,0.219 10 false 13 3.042,1.99 3.313,2.208 0.271,0.219 10 false 12 3.031,1.281 3.302,1.5 0.271,0.219 10 false 26 4.104,1.99 4.292,2.198 0.188,0.208 10 false 2 4.396,3.219 4.583,3.427 0.188,0.208 10 false 6 4.396,5.24 4.583,5.448 0.188,0.208 10 false 3 4.365,5.833 4.552,6.042 0.188,0.208 10 false 13 4.375,3.802 4.563,4.01 0.188,0.208 10 false 16 5.219,3.115 5.406,3.323 0.188,0.208 10 false R 5.177,3.896 5.365,4.104 0.188,0.208 10 false W 5.667,5.229 5.854,5.438 0.188,0.208 10 false 6 5.781,5.823 5.969,6.031 0.188,0.208 10 false 14 5.573,3.229 5.76,3.438 0.188,0.208 10 false 14 0.104,5.01 0.406,5.208 0.302,0.198 10 false F14 0.156,3.146 0.458,3.344 0.302,0.198 10 false p1 0.104,6.802 0.406,7 0.302,0.198 10 false F58 5.542,4.094 5.844,4.292 0.302,0.198 10 false F19 6.031,5.917 6.365,6.115 0.333,0.198 10 false F25 6.333,5.917 6.75,6.104 0.417,0.188 10 false DLC3 5.844,4.094 7.021,4.656 1.177,0.563 10 false Main Body ECU (Multiplex Network Body ECU) 0.333,3.146 1.646,3.583 1.313,0.438 10 false Power Steering ECU Assembly 0.417,5.01 1.781,5.26 1.365,0.25 10 false 4WD ECU Assembly* 0.417,6.802 1.781,7.052 1.365,0.25 10 false Steering Sensor 0.781,8.042 2.688,8.281 1.906,0.24 10 false : CAN Main Bus Line (CANH) 0.813,8.448 2.719,8.688 1.906,0.24 10 false : CAN Main Bus Line (CANL) 3.927,8.021 5.833,8.26 1.906,0.24 10 false : CAN Branch Line (CANH) 3.938,8.427 5.844,8.667 1.906,0.24 10 false : CAN Branch Line (CANL) 1.854,2.177 2.042,2.385 0.188,0.208 10 false W 2.448,2.958 2.635,3.167 0.188,0.208 10 false W

C295126
5.635,0.135 6.885,0.406 1.25,0.271 10 false x: Suspected Area 0.146,0.115 1.448,0.385 1.302,0.271 12 false V Bus: 0.219,1.01 2.281,1.49 2.063,0.479 10 false *1: w/ Automatic Headlight Beam Level Control System 0.219,1.698 2.719,1.948 2.5,0.25 10 false *2: w/ Smart Entry and Start System 0.583,2.406 1.135,2.646 0.552,0.24 10 false F102 0.979,2.406 2.99,2.646 2.01,0.24 10 false No. 3 CAN Junction Connector 4.521,1.375 4.677,1.573 0.156,0.198 10 false 9 4.229,3.281 4.385,3.479 0.156,0.198 10 false 1 4.229,4.219 4.385,4.417 0.156,0.198 10 false 1 4.531,4.615 4.688,4.813 0.156,0.198 10 false 2 5.76,1.396 5.917,1.594 0.156,0.198 10 false 6 2.917,5.667 3.073,5.865 0.156,0.198 10 false 4 5.771,1.979 5.927,2.177 0.156,0.198 10 false 7 4.49,1.979 4.729,2.188 0.24,0.208 10 false 19 3.177,4.24 3.417,4.448 0.24,0.208 10 false 11 3.156,3.271 3.396,3.479 0.24,0.208 10 false 11 4.5,5.198 4.74,5.406 0.24,0.208 10 false 12 5.677,5.198 5.917,5.406 0.24,0.208 10 false 14 5.677,4.615 5.917,4.823 0.24,0.208 10 false 25 1.24,5.688 1.479,5.896 0.24,0.208 10 false 13 1.25,6.26 1.49,6.469 0.24,0.208 10 false 22 2.865,6.271 3.104,6.479 0.24,0.208 10 false 14 4.51,7.677 4.75,7.885 0.24,0.208 10 false 17 5.76,7.677 6,7.885 0.24,0.208 10 false 8 4.552,7.083 4.792,7.292 0.24,0.208 10 false 7 5.76,7.083 6,7.292 0.24,0.208 10 false 7 5.25,1.313 5.563,1.51 0.313,0.198 10 false GR 5.26,4.521 5.552,4.75 0.292,0.229 10 false GR 5.667,2.25 5.979,2.448 0.313,0.198 10 false A67 4.26,3.76 4.573,3.958 0.313,0.198 10 false BR 5.281,2.063 5.594,2.26 0.313,0.198 10 false W 3.125,3.771 3.333,4.042 0.208,0.271 10 false W 5.958,2.24 7.083,2.667 1.125,0.427 10 false Headlight Leveling ECU Assembly*1 5.948,1.979 6.417,2.177 0.469,0.198 10 false CANL 5.938,4.615 6.406,4.813 0.469,0.198 10 false CANH 5.948,1.396 6.417,1.594 0.469,0.198 10 false CANH 0.771,5.688 1.24,5.885 0.469,0.198 10 false CANH 5.948,7.104 6.417,7.302 0.469,0.198 10 false CANH 5.948,5.198 6.417,5.396 0.469,0.198 10 false CANL 5.948,7.677 6.417,7.875 0.469,0.198 10 false CANL 0.802,6.26 1.271,6.458 0.469,0.198 10 false CANL 1.042,4.677 3.052,4.917 2.01,0.24 10 false No. 4 CAN Junction Connector 0.635,4.677 1.052,4.917 0.417,0.24 10 false F103 5.292,7.76 5.5,8.031 0.208,0.271 10 false W 2.24,5.583 2.448,5.854 0.208,0.271 10 false Y 5.313,7.01 5.521,7.281 0.208,0.271 10 false G 5.271,5.271 5.479,5.542 0.208,0.271 10 false W 5.677,5.469 6.021,5.677 0.344,0.208 10 false A47 5.979,5.469 7.083,6 1.104,0.531 10 false Skid Control ECU (Brake Actuator Assembly) 5.719,7.948 6.052,8.167 0.333,0.219 10 false F13 6.021,7.948 7.094,8.479 1.073,0.531 10 false Certification ECU (Smart Key ECU Assembly)*2 0.052,6.552 0.375,6.75 0.323,0.198 10 false F38 0.365,6.552 1.292,6.979 0.927,0.427 10 false Airbag Sensor Assembly 2.219,6.354 2.427,6.625 0.208,0.271 10 false W 0.76,9.042 2.677,9.323 1.917,0.281 10 false : CAN Main Bus Line (CANH) 3.917,9.438 5.833,9.719 1.917,0.281 10 false : CAN Branch Line (CANL) 0.781,9.427 2.698,9.708 1.917,0.281 10 false : CAN Main Bus Line (CANL) 3.927,9.063 5.844,9.344 1.917,0.281 10 false : CAN Branch Line (CANH)

C301926
0.073,0.052 1.177,0.292 1.104,0.24 12 false V Bus: 5.365,0.063 6.792,0.344 1.427,0.281 10 false x: Suspected Area 4.531,0.813 5.146,1.01 0.615,0.198 10 false F103 4.938,0.813 7.063,1.104 2.125,0.292 10 false No. 4 CAN Junction Connector 2.927,0.646 3.083,0.844 0.156,0.198 10 false 3 2.885,1.25 3.198,1.448 0.313,0.198 10 false 13 2.208,0.594 2.521,0.792 0.313,0.198 10 false BE 2.219,1.344 2.375,1.542 0.156,0.198 10 false W 0.771,0.677 1.385,0.875 0.615,0.198 10 false CANH 0.781,1.26 1.396,1.458 0.615,0.198 10 false CANL 1.26,0.667 1.573,0.865 0.313,0.198 10 false 11 1.26,1.281 1.573,1.479 0.313,0.198 10 false 12 0.042,1.521 0.5,1.719 0.458,0.198 10 false F80 0.365,1.521 1.948,2.406 1.583,0.885 10 false Air Conditioning Amplifier Assembly 4.542,2.24 4.698,2.438 0.156,0.198 10 false 6 4.51,2.844 4.823,3.042 0.313,0.198 10 false 16 5.313,2.198 5.469,2.396 0.156,0.198 10 false L 5.271,2.927 5.427,3.125 0.156,0.198 10 false W 5.76,2.25 5.917,2.448 0.156,0.198 10 false 9 5.719,2.844 6.031,3.042 0.313,0.198 10 false 10 5.583,3.094 6.042,3.292 0.458,0.198 10 false F71 5.938,3.094 7.104,4.313 1.167,1.219 10 false Radio and Display Receiver Assembly*2 5.969,2.24 6.583,2.438 0.615,0.198 10 false CANH 5.969,2.844 6.583,3.042 0.615,0.198 10 false CANL 2.865,3.51 3.177,3.708 0.313,0.198 10 false 10 2.875,4.115 3.188,4.313 0.313,0.198 10 false 20 2.24,3.417 2.396,3.615 0.156,0.198 10 false P 2.229,4.167 2.385,4.365 0.156,0.198 10 false W 1.25,3.49 1.563,3.688 0.313,0.198 10 false 16 1.26,4.094 1.573,4.292 0.313,0.198 10 false 15 0.792,3.49 1.406,3.688 0.615,0.198 10 false CA1H 0.813,4.125 1.427,4.323 0.615,0.198 10 false CA1L 0.052,4.365 0.51,4.563 0.458,0.198 10 false F85 0.365,4.365 1.51,5.229 1.146,0.865 10 false Network Gateway ECU*1 0.125,5.594 2.229,7.052 2.104,1.458 10 false *1: w/ Blind Spot Monitor System or Parking Assist Monitor System 0.125,6.292 4.875,6.563 4.75,0.271 10 false *2: for Radio and Display Type 4.229,5.979 4.385,6.177 0.156,0.198 10 false 8 3.167,5.979 3.479,6.177 0.313,0.198 10 false 18 4.271,6.302 4.583,6.5 0.313,0.198 10 false SB 3.135,6.313 3.292,6.51 0.156,0.198 10 false W 4.24,6.604 4.552,6.802 0.313,0.198 10 false 17 3.156,6.604 3.469,6.802 0.313,0.198 10 false 16 4.25,6.833 4.865,7.031 0.615,0.198 10 false CANH 2.948,6.833 3.563,7.031 0.615,0.198 10 false CANL 3.583,7.323 4.354,7.521 0.771,0.198 10 false 120 Ω 4.75,7.146 5.208,7.344 0.458,0.198 10 false F22 5.094,7.146 6.979,7.438 1.885,0.292 10 false Combination Meter Assembly 3.979,8.375 5.813,8.667 1.833,0.292 10 false : CAN Branch Line (CANL) 3.99,7.99 5.917,8.26 1.927,0.271 10 false : CAN Branch Line (CANH) 0.844,8.354 4.823,8.552 3.979,0.198 10 false : CAN Main Bus Line (CANL) 0.844,7.979 4.823,8.177 3.979,0.198 10 false : CAN Main Bus Line (CANH)

CAUTION / NOTICE / HINT

NOTICE:
·

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key, switches or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING

·

After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

·

DTC check procedure: Turn the ignition switch to ON and wait at least 60 seconds, and then drive the vehicle at a speed of 60 km/h (37 mph) or more for 7 seconds or more.

·

After the repair, perform the CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM

·

If the main body ECU (multiplex network body ECU) is replaced, refer to Registration.*

*: w/ Smart Entry and Start System




HINT:
·

Operating the ignition switch, any other switches or a door triggers related ECU and sensor communication on the CAN. This communication will cause the resistance value to change.

·

Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.



PROCEDURE

1.CHECK FOR SHORT TO GND IN CAN BUS LINE (NO. 3 CAN JUNCTION CONNECTOR)
a.

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the F102 No. 3 CAN junction connector.

C287238
5.313,0.104 5.792,0.406 0.479,0.302 2.073,0.125 2.521,0.438 0.448,0.313 5.802,0.979 5.625,0.979 5.625,0.979 5.427,1.635 true 1.5,2.073 0.927,1.417 0.927,1.417 0.813,1.417 true 0.896,2.917 1.01,2.917 1.01,2.917 1.521,2.292 true 1.719,2.073 1.094,0.917 1.094,0.917 0.969,0.917 true 1.083,3.292 1.177,3.292 1.177,3.292 1.729,2.281 true 1.583,3.51 1.688,3.51 1.688,3.51 1.938,2.281 true 1.948,2.073 1.635,0.406 1.635,0.406 1.51,0.406 true 2.167,2.052 2.698,0.323 2.698,0.323 2.802,0.323 true 2.479,3.604 2.365,3.604 2.365,3.604 2.167,2.281 true 0.896,2.542 1,2.542 1,2.542 1.271,2.281 true 1.281,2.073 0.979,1.833 0.979,1.833 0.875,1.833 true 2.406,2.052 2.958,0.542 2.958,0.542 3.073,0.542 true 2.917,3.375 2.76,3.375 2.76,3.375 2.396,2.271 true 2.833,2.063 3.323,0.781 3.323,0.781 3.438,0.781 true 3.333,3.177 3.219,3.177 3.219,3.177 2.844,2.281 true 3.052,2.063 3.479,1.073 3.479,1.073 3.594,1.073 true 3.417,2.938 3.313,2.938 3.313,2.938 3.052,2.271 true 0.052,0.042 0.365,0.24 0.313,0.198 10 false *a 4.667,0.156 4.979,0.354 0.313,0.198 10 false *1 5.885,0.885 6.344,1.083 0.458,0.198 10 false CG 0.323,1.75 1.24,1.948 0.917,0.198 10 false CANH*b 0.375,2.448 1.292,2.646 0.917,0.198 10 false CANL*b 0.281,1.323 1.198,1.521 0.917,0.198 10 false CANH*c 0.375,2.833 1.073,3.083 0.698,0.25 10 false CANL*c 0.365,0.823 1.281,1.021 0.917,0.198 10 false CANH*d 0.51,3.198 1.427,3.396 0.917,0.198 10 false CANL*d 5.427,0.156 5.729,0.354 0.302,0.198 10 false F25 2.146,0.177 2.76,0.375 0.615,0.198 10 false F102 1.042,3.396 1.688,3.604 0.646,0.208 10 false CANL*e 0.948,0.313 1.896,0.51 0.948,0.198 10 false CANH*e 2.865,0.229 3.781,0.427 0.917,0.198 10 false CANH*f 2.531,3.51 3.448,3.708 0.917,0.198 10 false CANL*f 3.115,0.458 4.031,0.656 0.917,0.198 10 false CANH*g 2.969,3.292 3.885,3.49 0.917,0.198 10 false CANL*g 3.51,0.688 4.427,0.885 0.917,0.198 10 false CANH*h 3.406,3.083 4.323,3.281 0.917,0.198 10 false CANL*h 3.469,2.854 4.385,3.052 0.917,0.198 10 false CANL*i 3.646,0.979 4.563,1.177 0.917,0.198 10 false CANH*i
*1 DLC3 - -
*a Front view of wire harness connector
(to No. 3 CAN Junction Connector)
*b to No. 4 CAN Junction Connector
*c to ECM *d to DLC3
*e to Steering Sensor *f to Power Steering ECU Assembly
*g to Main Body ECU (Multiplex Network Body ECU) *h to 4WD ECU Assembly
(for AWD)
*i to Headlight Leveling ECU Assembly
(w/ Automatic Headlight Beam Level Control System)
- -



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to
F102-1 (CANH) - F25-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher No. 4 CAN junction connector
F102-11 (CANL) - F25-4 (CG)
F102-2 (CANH) - F25-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher ECM
F102-12 (CANL) - F25-4 (CG)
F102-3 (CANH) - F25-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher DLC3
F102-13 (CANL) - F25-4 (CG)
F102-4 (CANH) - F25-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher Steering sensor
F102-14 (CANL) - F25-4 (CG)
F102-5 (CANH) - F25-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher Power steering ECU assembly
F102-15 (CANL) - F25-4 (CG)
F102-6 (CANH) - F25-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher Main body ECU (multiplex network body ECU)
F102-16 (CANL) - F25-4 (CG)
F102-8 (CANH) - F25-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher 4WD ECU assembly*1
F102-18 (CANL) - F25-4 (CG)
F102-9 (CANH) - F25-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher Headlight leveling ECU assembly*2
F102-19 (CANL) - F25-4 (CG)


·

*1: for AWD

·

*2: w/ Automatic Headlight Beam Level Control System



Result:
Result Proceed to
OK A
NG (No. 4 CAN junction connector main line) B
NG (ECU or sensor bus line) C
NG (DLC3 branch line) D



A

REPLACE NO. 3 CAN JUNCTION CONNECTOR

B

2.CHECK FOR SHORT TO GND IN CAN BUS LINE (NO. 4 CAN JUNCTION CONNECTOR)

C

3.CHECK FOR SHORT TO GND IN CAN BUS LINE (ECU, SENSOR)

D

REPAIR OR REPLACE CAN BRANCH LINE CONNECTED TO DLC3

2.CHECK FOR SHORT TO GND IN CAN BUS LINE (NO. 4 CAN JUNCTION CONNECTOR)
a.

Reconnect the F102 No. 3 CAN junction connector.


b.

Disconnect the F103 No. 4 CAN junction connector.

C287238
5.313,0.104 5.771,0.406 0.458,0.302 2.073,0.125 2.521,0.427 0.448,0.302 5.781,1.031 5.688,1.031 5.688,1.031 5.438,1.646 true 1.5,2.073 0.927,1.417 0.927,1.417 0.813,1.417 true 0.896,2.917 1.01,2.917 1.01,2.917 1.521,2.292 true 1.719,2.073 1.094,0.917 1.094,0.917 0.969,0.917 true 1.083,3.292 1.177,3.292 1.177,3.292 1.729,2.281 true 1.448,3.51 1.563,3.51 1.563,3.51 1.938,2.281 true 1.948,2.073 1.333,0.615 1.333,0.615 1.208,0.615 true 0.896,2.542 1,2.542 1,2.542 1.271,2.281 true 1.281,2.073 0.979,1.833 0.979,1.833 0.875,1.833 true 2.385,2.063 2.927,0.292 2.927,0.292 3.052,0.292 true 2.885,3.656 2.771,3.656 2.771,3.656 2.396,2.271 true 2.615,2.083 3.115,0.563 3.115,0.563 3.219,0.563 true 3.167,3.365 3.073,3.365 3.073,3.365 2.615,2.281 true 2.833,2.083 3.323,0.865 3.323,0.865 3.396,0.865 true 3.323,3.063 3.219,3.063 3.219,3.063 2.865,2.271 true 3.281,2.073 3.615,1.635 3.615,1.635 3.729,1.635 true 3.76,2.5 3.667,2.5 3.667,2.5 3.292,2.292 true 0.052,0.042 0.365,0.24 0.313,0.198 10 false *a 4.51,0.135 4.823,0.333 0.313,0.198 10 false *1 5.885,0.938 6.344,1.135 0.458,0.198 10 false CG 0.323,1.75 1.24,1.948 0.917,0.198 10 false CANH*b 0.375,2.448 1.292,2.646 0.917,0.198 10 false CANL*b 0.281,1.323 1.198,1.521 0.917,0.198 10 false CANH*c 0.375,2.833 1.073,3.083 0.698,0.25 10 false CANL*c 0.406,0.823 1.323,1.021 0.917,0.198 10 false CANH*d 0.552,3.188 1.469,3.385 0.917,0.198 10 false CANL*d 0.635,0.531 1.552,0.729 0.917,0.198 10 false CANH*e 0.885,3.427 1.802,3.625 0.917,0.198 10 false CANL*e 5.417,0.167 5.729,0.365 0.313,0.198 10 false F25 2.146,0.177 2.76,0.375 0.615,0.198 10 false F103 2.958,3.563 3.875,3.76 0.917,0.198 10 false CANL*f 3.135,0.198 4.052,0.396 0.917,0.198 10 false CANH*f 3.854,2.406 4.771,2.604 0.917,0.198 10 false CANL*i 3.49,0.771 4.406,0.969 0.917,0.198 10 false CANH*h 3.417,2.969 4.333,3.167 0.917,0.198 10 false CANL*h 3.823,1.542 4.74,1.74 0.917,0.198 10 false CANH*i 3.26,3.271 4.177,3.469 0.917,0.198 10 false CANL*g 3.313,0.469 4.229,0.667 0.917,0.198 10 false CANH*g
*1 DLC3 - -
*a Front view of wire harness connector
(No. 4 CAN Junction Connector)
*b to No. 3 CAN Junction Connector
(for V Bus)
*c to Skid Control ECU (Brake Actuator Assembly)
(for V Bus)
*d to Air Conditioning Amplifier Assembly
(for V Bus)
*e to Airbag Sensor Assembly
(for V Bus)
*f to Radio and Display Receiver Assembly
(for Radio and Display Type)
(for V Bus)
*g to Certification ECU (Smart Key ECU Assembly)
(w/ Smart Entry and Start System)
(for V Bus)
*h to Combination Meter Assembly
(for V Bus)
*i to Network Gateway ECU
(w/ Blind Spot Monitor System or Parking Assist Monitor System)
(for V Bus)
- -



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to
F103-1 (CANH) - F25-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher No. 3 CAN junction connector
F103-11 (CANL) - F25-4 (CG)
F103-2 (CANH) - F25-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher Skid control ECU (brake actuator assembly)
F103-12 (CANL) - F25-4 (CG)
F103-3 (CANH) - F25-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher Air conditioning amplifier assembly
F103-13 (CANL) - F25-4 (CG)
F103-4 (CANH) - F25-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher Airbag sensor assembly
F103-14 (CANL) - F25-4 (CG)
F103-6 (CANH) - F25-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher Radio and display receiver assembly*1
F103-16 (CANL) - F25-4 (CG)
F103-7 (CANH) - F25-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher Certification ECU (smart key ECU assembly)*2
F103-17 (CANL) - F25-4 (CG)
F103-8 (CANH) - F25-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher Combination meter assembly
F103-18 (CANL) - F25-4 (CG)
F103-10 (CANH) - F25-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher Network gateway ECU*3
F103-20 (CANL) - F25-4 (CG)


·

*1: for Radio and Display Type

·

*2: w/ Smart Entry and Start System

·

*3: w/ Blind Spot Monitor System or Parking Assist Monitor System



Result:
Result Proceed to
OK A
NG (No. 3 CAN junction connector main line) B
NG (ECU or sensor bus line) C



A

REPLACE NO. 4 CAN JUNCTION CONNECTOR

B

REPAIR OR REPLACE CAN MAIN BUS LINE OR CONNECTOR (NO. 3 CAN JUNCTION CONNECTOR - NO. 4 CAN JUNCTION CONNECTOR)

C

3.CHECK FOR SHORT TO GND IN CAN BUS LINE (ECU, SENSOR)
3.CHECK FOR SHORT TO GND IN CAN BUS LINE (ECU, SENSOR)
a.

Reconnect all wire harness connectors.


b.

Disconnect the ECU or sensor connected to the CAN bus line that is shorted to ground.

HINT:

If the ECU or sensor has multiple connectors, disconnect the connector that includes the CAN bus lines. To determine the ECU or sensor that is connected to the shorted bus line, refer to Terminals of ECU.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>TERMINALS OF ECU



c.
C292403
1.5,0.104 1.938,0.375 0.438,0.271 2.042,0.823 2.396,0.323 2.396,0.323 2.531,0.323 true 1.552,1.938 1.708,1.938 1.708,1.938 2.042,1.438 true 1.594,0.802 1.167,0.333 1.167,0.333 1,0.333 true 0.094,0.083 0.406,0.281 0.313,0.198 10 false *1 1.594,0.146 1.906,0.344 0.313,0.198 10 false F25 2.604,0.229 3.219,0.427 0.615,0.198 10 false CANH 1.115,1.844 1.729,2.042 0.615,0.198 10 false CANL 0.719,0.25 1.333,0.448 0.615,0.198 10 false CG
*1 DLC3


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F25-6 (CANH) - F25-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
F25-14 (CANL) - F25-4 (CG)


HINT:

If the resistance changes to 200 Ω or higher when the connector is disconnected from the ECU or sensor, there may be a short in the ECU or sensor.



Result:
Result
OK
NG



OK

REPLACE CORRESPONDING ECU OR SENSOR

NG

REPAIR OR REPLACE CORRESPONDING ECU OR SENSOR BRANCH LINES OR CONNECTOR