Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM › 2013.12–2016.11
RM3160E _57 Power Source / Network _019704 NETWORKING _0095663 CAN COMMUNICATION SYSTEM C

NETWORKING  CAN COMMUNICATION SYSTEM  U0265  Lost Communication with Parking Assist Monitor Module  


DESCRIPTION

DTC No. Detection Item DTC Detection Condition Trouble Area Note
U0265 Lost Communication with Parking Assist Monitor Module No communication from the television camera assembly continues.
·

Television camera assembly branch line or connector

·

Power source circuit of television camera assembly

·

Television camera assembly ground circuit

·

Television camera assembly


HINT:

Network gateway ECU stores DTCs when it detects a communication stop or network communication error for ECUs connected to sub bus 2.



HINT:

This diagnosis procedure is for when DTC U0265 is output by the network gateway ECU (GTS display: Gateway).


WIRING DIAGRAM

C294447
1.813,1.125 1.479,0.5 1.479,0.5 1.365,0.5 false 3.573,1.125 3.24,0.5 3.24,0.5 3.125,0.5 false 0.042,0.021 1.875,0.26 1.833,0.24 12 false Sub Bus 2: 6.01,4.844 6.906,5.052 0.896,0.208 10 false Trouble Area 4.271,5.063 6.073,5.344 1.802,0.281 10 false : CAN Branch Line (CANH) 4.271,5.396 6.125,5.667 1.854,0.271 10 false : CAN Branch Line (CANL) 1.146,5.063 5.125,5.26 3.979,0.198 10 false : CAN Main Bus Line (CANH) 1.146,5.396 5.125,5.594 3.979,0.198 10 false : CAN Main Bus Line (CANL) 3.177,4.333 7.156,4.531 3.979,0.198 10 false Television Camera Assembly 2.854,4.333 3.313,4.531 0.458,0.198 10 false X13 3.26,3.667 3.719,3.865 0.458,0.198 10 false CB+ 3.469,3.49 4.083,3.688 0.615,0.198 10 false CANH 3.969,3.49 4.583,3.688 0.615,0.198 10 false CANL 4.219,3.646 4.833,3.844 0.615,0.198 10 false CGND 4.677,3.542 4.833,3.74 0.156,0.198 10 false 5 4.167,3.271 4.5,3.698 0.333,0.427 10 false 1 3.594,3.281 3.75,3.479 0.156,0.198 10 false 4 3.083,3.552 3.24,3.75 0.156,0.198 10 false 6 5.688,2.656 7.156,3.146 1.469,0.49 10 false CAN Junction Terminal 0.313,2.646 1.448,3.229 1.135,0.583 10 false Network Gateway ECU 0.677,2.01 1.448,2.208 0.771,0.198 10 false 120 Ω 6.125,2.021 6.896,2.219 0.771,0.198 10 false 120 Ω 0.625,3.656 2.615,4.802 1.99,1.146 10 false Navigation Receiver Assembly*1 or Radio and Display Receiver Assembly*2 5.198,3.594 6.594,4.667 1.396,1.073 10 false Navigation Receiver Assembly*1 or Radio and Display Receiver Assembly*2 0.063,0.396 1.302,0.885 1.24,0.49 10 false No. 1 CAN Junction Connector 1.833,0.406 3.073,0.896 1.24,0.49 10 false No. 2 CAN Junction Connector 4.479,0.135 6.521,0.49 2.042,0.354 10 false *1: for Navigation Receiver Type 4.479,0.458 7.156,0.792 2.677,0.333 10 false *2: for Radio and Display Type

CAUTION / NOTICE / HINT

NOTICE:
·

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key, switches or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING

·

After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

·

DTC check procedure: Turn the ignition switch to ON and wait at least 14 seconds.

·

After the repair, perform the CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM

·

Inspect the fuses for circuits related to this system before performing the following procedure.



HINT:
·

Operating the ignition switch, any other switches or a door triggers related ECU and sensor communication on the CAN. This communication will cause the resistance value to change.

·

Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.



PROCEDURE

1.RECONFIRM DTC OUTPUT
Body Electrical > Gateway > Trouble Codes
50001 150
a.

Reconfirm DTCs.

HINT:

If DTC U1002 is output from Gateway of the network gateway ECU, this indicates a sub bus 2 malfunction. Troubleshoot for DTC U1002 and check for malfunctions in sub bus 2.



Result:
Result Proceed to
U1002 is not output from network gateway ECU (GTS display: Gateway) A
U1002 is output from network gateway ECU (GTS display: Gateway) B



A

2.CHECK FOR OPEN IN SUB BUS 2 LINES (TELEVISION CAMERA ASSEMBLY BRANCH LINE)

B

GO TO DIAGNOSIS PROCEDURE INDICATED BY OUTPUT DTC

2.CHECK FOR OPEN IN SUB BUS 2 LINES (TELEVISION CAMERA ASSEMBLY BRANCH LINE)
a.

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the X13 television camera assembly connector.


c.
C294680
1.573,0.188 1.958,0.479 0.385,0.292 0.979,1.958 1.146,1.958 1.146,1.958 1.563,1.417 true 0.99,0.563 1.135,0.563 1.135,0.563 1.552,1.156 true 0.094,0.073 0.406,0.271 0.313,0.198 10 false *a 1.646,0.229 2.104,0.427 0.458,0.198 10 false X13 0.583,0.469 1.198,0.667 0.615,0.198 10 false CANL 0.563,1.865 1.177,2.063 0.615,0.198 10 false CANH
*a Front view of wire harness connector
(to Television Camera Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
X13-4 (CANH) - X13-1 (CANL) Cable disconnected from negative (-) battery terminal 54 to 69 Ω



Result:
Result
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)

NG

REPAIR OR REPLACE CAN BRANCH LINE OR CONNECTOR (TELEVISION CAMERA ASSEMBLY)

3.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)
a.
C294680
1.573,0.188 1.958,0.479 0.385,0.292 1.198,1.958 1.365,1.958 1.365,1.958 1.781,1.417 true 0.094,0.073 0.406,0.271 0.313,0.198 10 false *a 1.656,0.229 2.115,0.427 0.458,0.198 10 false X13 0.76,1.865 1.375,2.063 0.615,0.198 10 false CGND
*a Front view of wire harness connector
(to Television Camera Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
X13-5 (CGND) - Body ground Cable disconnected from negative (-) battery terminal Below 1 Ω



b.

Reconnect the cable to the negative (-) battery terminal.


c.
C294680
1.573,0.188 1.958,0.479 0.385,0.292 1.385,1.958 1.552,1.958 1.552,1.958 1.969,1.417 true 0.094,0.073 0.406,0.271 0.313,0.198 10 false *a 1.635,0.229 2.094,0.427 0.458,0.198 10 false X13 1.052,1.865 1.667,2.063 0.615,0.198 10 false CB+
*a Front view of wire harness connector
(to Television Camera Assembly)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
X13-6 (CB+) - Body ground Ignition switch ACC 5.5 to 7.05 V



Result:
Result
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)