Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM › 2013.12–2016.11
RM3160E _57 Power Source / Network _019704 NETWORKING _0095663 CAN COMMUNICATION SYSTEM C

NETWORKING  CAN COMMUNICATION SYSTEM  U1002  Lost Communication with Gateway Module (Network Gateway ECU)  


DESCRIPTION

·

The network gateway ECU will store this DTC when no signals can be received from the ECUs that have been memorized as those that are connected to sub bus 2.

·

When the network gateway ECU receives a response signal from the ECUs connected to sub bus 2, the network gateway ECU recognizes and memorizes that the ECU is connected to sub bus 2. Based on this memorized data, the network gateway ECU monitors for malfunctions in the ECUs connected to sub bus 2 when communicating with those ECUs. If the network gateway ECU cannot receive response signals from the ECUs that have been memorized as those connected to sub bus 2, the network gateway ECU determines that a malfunction exists.


DTC No. Detection Item DTC Detection Condition Trouble Area Note
U1002 Lost Communication with Gateway Module (Network Gateway ECU) The network gateway ECU cannot receive signals from all ECUs that have been memorized as those connected to sub bus 2.
·

Open or short in sub bus 2 main line or connector

·

Open or short in sub bus 2 branch line or connector

·

Network gateway ECU

·

Driving support ECU assembly

(w/ Pre-crash safety system)

·

Lane departure warning camera

(w/ Lane departure alert system)

·

Television camera assembly

(w/ Parking assist monitor system)

·

Blind spot monitor sensor LH

(w/ Blind spot monitor system)

·

Open or short in No. 1 CAN junction connector

·

Open or short in No. 2 CAN junction connector

·

Open or short in CAN junction terminal


HINT:

The network gateway ECU stores DTCs when it detects a communication stop or network communication error for ECUs connected to sub bus 2.



HINT:

This diagnosis procedure is for when DTC U1002 is output by the network gateway ECU (GTS display: Gateway).


WIRING DIAGRAM

C295222
0.073,0.052 3.74,0.292 3.667,0.24 12 false Sub Bus 2 (for LHD): 5.49,0.052 7.156,0.396 1.667,0.344 10 false x: Suspected Area 5.083,0.583 6.677,0.906 1.594,0.323 10 false Network Gateway ECU 4.76,0.583 5.219,0.781 0.458,0.198 10 false F85 3.615,0.469 4.385,0.667 0.771,0.198 10 false 120 Ω 2.948,0.927 3.563,1.125 0.615,0.198 10 false CA2L 4.26,0.927 4.875,1.125 0.615,0.198 10 false CA2H 4.229,1.188 4.542,1.385 0.313,0.198 10 false 13 3.146,1.198 3.458,1.396 0.313,0.198 10 false 12 4.25,1.479 4.406,1.677 0.156,0.198 10 false L 3.135,1.479 3.292,1.677 0.156,0.198 10 false W 4.208,1.823 4.365,2.021 0.156,0.198 10 false 1 3.25,1.833 3.406,2.031 0.156,0.198 10 false 2 4,2.031 4.615,2.229 0.615,0.198 10 false F105 3.25,2.031 3.865,2.229 0.615,0.198 10 false F105 4.604,2.531 4.76,2.729 0.156,0.198 10 false 1 4.604,3.302 4.76,3.5 0.156,0.198 10 false 2 4.198,3.625 4.354,3.823 0.156,0.198 10 false 1 3.229,3.625 3.385,3.823 0.156,0.198 10 false 2 4.198,4.188 4.354,4.385 0.156,0.198 10 false 1 3.26,4.177 3.417,4.375 0.156,0.198 10 false 2 4.25,3.865 4.563,4.063 0.313,0.198 10 false BR 3.156,3.875 3.313,4.073 0.156,0.198 10 false W 5.417,3.26 5.573,3.458 0.156,0.198 10 false W 5.438,2.563 5.594,2.76 0.156,0.198 10 false R 3.99,3.427 4.604,3.625 0.615,0.198 10 false F104 4.5,3.094 5.115,3.292 0.615,0.198 10 false F108 5.74,2.615 5.896,2.813 0.156,0.198 10 false 6 5.688,3.229 6,3.427 0.313,0.198 10 false 12 5.948,2.604 6.563,2.802 0.615,0.198 10 false CA1P 5.969,3.24 6.583,3.438 0.615,0.198 10 false CA1N 5.646,3.469 7.156,4.24 1.51,0.771 10 false Lane Departure Warning Camera*2 5.385,3.469 5.698,3.667 0.313,0.198 10 false S4 3.24,3.427 3.854,3.625 0.615,0.198 10 false F104 1.094,2.667 5.375,2.865 4.281,0.198 10 false No. 1 CAN Junction Connector 4.49,2.719 5.104,2.917 0.615,0.198 10 false F108 0.354,0.958 2.833,1.177 2.479,0.219 10 false *1: w/ Parking Assist Monitor System 0.354,1.271 5.552,1.469 5.198,0.198 10 false *2: w/ Lane Departure Alert System 0.354,1.573 5.25,1.771 4.896,0.198 10 false *3: w/ Blind Spot Monitor System 4.531,4.521 6.573,4.802 2.042,0.281 10 false No. 2 CAN Junction Connector 4.021,4.385 4.635,4.583 0.615,0.198 10 false M38 3.26,4.385 3.875,4.583 0.615,0.198 10 false M38 2.74,4.823 3.354,5.021 0.615,0.198 10 false M39 2.74,5.198 3.354,5.396 0.615,0.198 10 false M39 4.521,5.188 5.135,5.385 0.615,0.198 10 false M40 4.51,5.563 5.125,5.76 0.615,0.198 10 false M40 4.01,6 4.625,6.198 0.615,0.198 10 false M41 3.26,6 3.875,6.198 0.615,0.198 10 false M41 4.604,4.969 4.76,5.167 0.156,0.198 10 false 1 3.26,6.198 3.417,6.396 0.156,0.198 10 false 2 4.615,5.771 4.771,5.969 0.156,0.198 10 false 2 4.188,6.198 4.344,6.396 0.156,0.198 10 false 1 2.833,4.594 2.99,4.792 0.156,0.198 10 false 1 2.823,5.417 2.979,5.615 0.156,0.198 10 false 2 5.396,5.729 5.552,5.927 0.156,0.198 10 false W 3.156,6.531 3.313,6.729 0.156,0.198 10 false W 2.333,5.385 2.49,5.583 0.156,0.198 10 false W 5.375,5.01 5.688,5.208 0.313,0.198 10 false GR 2.354,4.677 2.51,4.875 0.156,0.198 10 false B 1.563,4.677 1.719,4.875 0.156,0.198 10 false L 1.563,5.385 1.719,5.583 0.156,0.198 10 false Y 0.792,4.729 1.406,4.927 0.615,0.198 10 false CANH 0.792,5.323 1.406,5.521 0.615,0.198 10 false CANL 0.052,5.583 0.51,5.781 0.458,0.198 10 false X13 0.333,5.583 1.469,6.021 1.135,0.438 10 false Television Camera Assembly*1 5.771,5.073 5.927,5.271 0.156,0.198 10 false 2 5.771,5.688 5.927,5.885 0.156,0.198 10 false 7 5.958,5.063 6.573,5.26 0.615,0.198 10 false CA1P 5.958,5.688 6.573,5.885 0.615,0.198 10 false CA1N 5.573,5.927 6.031,6.125 0.458,0.198 10 false M31 5.927,5.927 7.094,6.698 1.167,0.771 10 false Blind Spot Monitor Sensor LH*3 4.25,6.531 4.406,6.729 0.156,0.198 10 false B 4.219,6.75 4.375,6.948 0.156,0.198 10 false 3 3.24,6.76 3.396,6.958 0.156,0.198 10 false 2 4.229,7 4.844,7.198 0.615,0.198 10 false CANH 2.896,7.021 3.51,7.219 0.615,0.198 10 false CANL 3.604,7.458 4.375,7.656 0.771,0.198 10 false 120 Ω 0.938,7.167 1.552,7.365 0.615,0.198 10 false M42 1.292,7.167 2.99,7.365 1.698,0.198 10 false CAN Junction Terminal 0.792,8.021 4.771,8.219 3.979,0.198 10 false : CAN Main Bus Line (CANH) 0.802,8.406 4.781,8.604 3.979,0.198 10 false : CAN Main Bus Line (CANL) 3.958,8.042 5.802,8.271 1.844,0.229 10 false : CAN Branch Line (CANH) 3.958,8.406 5.719,8.667 1.76,0.26 10 false : CAN Branch Line (CANL) 1.271,4.729 1.427,4.927 0.156,0.198 10 false 4 1.26,5.344 1.417,5.542 0.156,0.198 10 false 1

C295260
0.063,0.052 3.115,0.323 3.052,0.271 12 false Sub Bus 2 (for RHD): 5.427,0.031 6.948,0.448 1.521,0.417 10 false x: Suspected Area 3.458,0.583 4.229,0.781 0.771,0.198 10 false 120 Ω 2.802,1.073 3.417,1.271 0.615,0.198 10 false CA2L 4.125,1.042 4.74,1.24 0.615,0.198 10 false CA2H 1.167,0.688 4.073,0.885 2.906,0.198 10 false Network Gateway ECU 0.833,0.688 1.292,0.885 0.458,0.198 10 false F85 4.094,1.313 4.406,1.51 0.313,0.198 10 false 13 3.021,1.302 3.333,1.5 0.313,0.198 10 false 12 4.125,1.531 4.281,1.729 0.156,0.198 10 false L 2.979,1.531 3.135,1.729 0.156,0.198 10 false W 1.979,3.573 2.135,3.771 0.156,0.198 10 false W 5.177,4.573 5.333,4.771 0.156,0.198 10 false W 3.021,6.969 3.177,7.167 0.156,0.198 10 false W 4.073,1.75 4.229,1.948 0.156,0.198 10 false 1 3.115,1.75 3.271,1.948 0.156,0.198 10 false 2 4.458,3.802 4.615,4 0.156,0.198 10 false 1 2.719,2.771 2.875,2.969 0.156,0.198 10 false 1 2.719,3.573 2.875,3.771 0.156,0.198 10 false 2 4.469,4.604 4.625,4.802 0.156,0.198 10 false 2 3.135,6.729 3.292,6.927 0.156,0.198 10 false 2 4.063,6.708 4.219,6.906 0.156,0.198 10 false 1 2,2.833 2.156,3.031 0.156,0.198 10 false G 5.198,3.865 5.354,4.063 0.156,0.198 10 false R 4.115,6.969 4.427,7.167 0.313,0.198 10 false BR 3.865,6.49 4.479,6.688 0.615,0.198 10 false F104 3.115,6.49 3.729,6.688 0.615,0.198 10 false F104 4.354,4.01 4.969,4.208 0.615,0.198 10 false F108 4.354,4.375 4.969,4.573 0.615,0.198 10 false F108 2.615,2.99 3.229,3.188 0.615,0.198 10 false F110 2.615,3.354 3.229,3.552 0.615,0.198 10 false F110 1.521,2.896 1.833,3.094 0.313,0.198 10 false 39 1.521,3.479 1.833,3.677 0.313,0.198 10 false 17 1.083,2.875 1.698,3.073 0.615,0.198 10 false CA2H 1.083,3.51 1.698,3.708 0.615,0.198 10 false CA2L 0.063,3.74 0.375,3.938 0.313,0.198 10 false F84 0.365,3.74 1.635,4.542 1.271,0.802 10 false Driving Support ECU Assembly*1 4.427,3.021 6.406,3.344 1.979,0.323 10 false No. 1 CAN Junction Connector 5.833,3.906 6.448,4.104 0.615,0.198 10 false CA1P 5.823,4.521 6.438,4.719 0.615,0.198 10 false CA1N 5.625,3.938 5.781,4.135 0.156,0.198 10 false 6 5.583,4.51 5.896,4.708 0.313,0.198 10 false 12 5.625,4.76 7.146,5.302 1.521,0.542 10 false Lane Departure Warning Camera*2 5.385,4.76 5.698,4.958 0.313,0.198 10 false S4 3.115,1.948 3.729,2.146 0.615,0.198 10 false F105 3.865,1.948 4.479,2.146 0.615,0.198 10 false F105 0.833,8.063 4.813,8.26 3.979,0.198 10 false : CAN Main Bus Line (CANH) 0.833,8.469 4.813,8.667 3.979,0.198 10 false : CAN Main Bus Line (CANL) 3.969,8.042 5.802,8.281 1.833,0.24 10 false : CAN Branch Line (CANH) 3.969,8.448 6.031,8.729 2.063,0.281 10 false : CAN Branch Line (CANL) 4.792,1.292 6.844,1.521 2.052,0.229 10 false *1: w/ Pre-crash Safety System 4.792,1.583 7.156,1.875 2.365,0.292 10 false *2: w/ Lane Departure Alert System

C294994
0.021,0.021 3.156,0.458 3.135,0.438 12 false Sub Bus 2 (for RHD): 4.906,0.052 6.5,0.427 1.594,0.375 10 false x: Suspected Area 4.104,0.865 4.417,1.063 0.313,0.198 10 false BR 3.021,0.865 3.177,1.063 0.156,0.198 10 false W 3.875,1.375 4.49,1.573 0.615,0.198 10 false M38 3.125,1.375 3.74,1.573 0.615,0.198 10 false M38 4.052,1.167 4.208,1.365 0.156,0.198 10 false 1 3.135,1.188 3.292,1.385 0.156,0.198 10 false 2 0.417,2.5 1.542,2.938 1.125,0.438 10 false Television Camera Assembly*1 0.104,2.5 0.563,2.698 0.458,0.198 10 false X13 1.063,1.646 1.677,1.844 0.615,0.198 10 false CANH 1.073,2.25 1.688,2.448 0.615,0.198 10 false CANL 1.542,1.656 1.698,1.854 0.156,0.198 10 false 4 1.542,2.24 1.698,2.438 0.156,0.198 10 false 1 1.823,1.573 1.979,1.771 0.156,0.198 10 false L 1.813,2.302 1.969,2.5 0.156,0.198 10 false Y 2.344,1.583 2.5,1.781 0.156,0.198 10 false B 2.344,2.292 2.5,2.49 0.156,0.198 10 false W 2.625,1.74 3.24,1.938 0.615,0.198 10 false M39 2.625,2.104 3.24,2.302 0.615,0.198 10 false M39 2.719,1.552 2.875,1.75 0.156,0.198 10 false 1 2.719,2.313 2.875,2.51 0.156,0.198 10 false 2 4.406,2.094 6.427,2.417 2.021,0.323 10 false No. 2 CAN Junction Connector 4.375,3.125 4.99,3.323 0.615,0.198 10 false M40 4.375,3.5 4.99,3.698 0.615,0.198 10 false M40 4.458,2.927 4.615,3.125 0.156,0.198 10 false 1 4.469,3.698 4.625,3.896 0.156,0.198 10 false 2 5.146,2.969 5.458,3.167 0.313,0.198 10 false GR 5.177,3.677 5.333,3.875 0.156,0.198 10 false W 5.656,3.031 5.813,3.229 0.156,0.198 10 false 2 5.646,3.615 5.802,3.813 0.156,0.198 10 false 7 5.813,3.021 6.427,3.219 0.615,0.198 10 false CA1P 5.813,3.615 6.427,3.813 0.615,0.198 10 false CA1N 5.469,3.865 5.927,4.063 0.458,0.198 10 false M31 5.792,3.865 6.979,4.542 1.188,0.677 10 false Blind Spot Monitor Sensor LH*2 3.875,4.5 4.49,4.698 0.615,0.198 10 false M41 3.125,4.5 3.74,4.698 0.615,0.198 10 false M41 4.063,4.698 4.219,4.896 0.156,0.198 10 false 1 3.115,4.698 3.271,4.896 0.156,0.198 10 false 2 4.104,4.938 4.26,5.135 0.156,0.198 10 false B 3.031,4.958 3.188,5.156 0.156,0.198 10 false W 4.073,5.208 4.229,5.406 0.156,0.198 10 false 3 3.135,5.208 3.292,5.406 0.156,0.198 10 false 2 4.135,5.438 4.75,5.635 0.615,0.198 10 false CANH 2.781,5.427 3.396,5.625 0.615,0.198 10 false CANL 3.49,5.938 4.26,6.135 0.771,0.198 10 false 120 Ω 0.771,5.844 1.385,6.042 0.615,0.198 10 false M42 1.135,5.844 2.698,6.042 1.563,0.198 10 false CAN Junction Terminal 4.781,5.031 7.156,5.281 2.375,0.25 10 false *1: w/ Parking Assist Monitor System 4.792,5.365 6.948,5.677 2.156,0.313 10 false *2: w/ Blind Spot Monitor System 0.813,6.833 4.792,7.031 3.979,0.198 10 false : CAN Main Bus Line (CANH) 0.813,7.229 4.792,7.427 3.979,0.198 10 false : CAN Main Bus Line (CANL) 3.948,6.813 5.813,7.115 1.865,0.302 10 false : CAN Branch Line (CANH) 3.948,7.219 5.74,7.448 1.792,0.229 10 false : CAN Branch Line (CANL)

CAUTION / NOTICE / HINT

NOTICE:
·

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key, switches or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING

·

After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

·

DTC check procedure: Turn the ignition switch to ON and wait at least 52 seconds, and then drive the vehicle at a speed of 50 km/h (31 mph) or more for 7 seconds or more.

·

After the repair, perform the CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM



HINT:
·

Operating the ignition switch, any other switches or a door triggers related ECU and sensor communication on the CAN. This communication will cause the resistance value to change.

·

Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.



PROCEDURE

1.CHECK VEHICLE TYPE
a.

Check vehicle type.


Result:
Result Proceed to
for LHD A
for RHD B



A

2.CHECK SUB BUS 2

B

22.CHECK SUB BUS 2
2.CHECK SUB BUS 2
a.

Disconnect the cable from the negative (-) battery terminal.


b.
C242747
1.458,0.177 1.885,0.448 0.427,0.271 0.854,1.635 0.969,1.635 0.969,1.635 1.542,1.083 true 1.021,1.865 1.104,1.865 1.104,1.865 1.625,1.083 true 1.385,0.948 1.104,0.531 1.104,0.531 1.01,0.531 true 2.042,0.938 2.354,0.531 2.354,0.531 2.458,0.531 true 0.104,0.073 0.417,0.271 0.313,0.198 10 false *a 1.542,0.219 2,0.417 0.458,0.198 10 false F85 0.458,1.542 1.073,1.74 0.615,0.198 10 false CA2H 0.656,1.771 1.271,1.969 0.615,0.198 10 false CA2L 0.677,0.448 1.135,0.646 0.458,0.198 10 false GND 2.51,0.438 3.125,0.635 0.615,0.198 10 false BATT
*a Component with harness connected
(Network Gateway ECU)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Result
F85-13 (CA2H) - F85-12 (CA2L) Cable disconnected from negative (-) battery terminal 54 to 69 Ω Below 54 Ω: Short circuit between bus lines
70 Ω or higher: Open circuit in a main bus line
F85-13 (CA2H) - F85-4 (GND) Cable disconnected from negative (-) battery terminal 200 Ω or higher Below 200 Ω: CANH ground short
F85-12 (CA2L) - F85-4 (GND) Cable disconnected from negative (-) battery terminal 200 Ω or higher Below 200 Ω: CANL ground short
F85-13 (CA2H) - F85-2 (BATT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher Below 6 kΩ: CANH +B short
F85-12 (CA2L) - F85-2 (BATT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher Below 6 kΩ: CANL +B short



Result:
Result Proceed to
OK A
Open circuit in CAN main bus line B
Short circuit between bus lines C
·

Ground short

·

+B short


D



A

3.CHECK FOR DTC OUTPUT

B

4.CHECK FOR OPEN IN SUB BUS 2 MAIN LINES (NETWORK GATEWAY ECU)

C

8.CHECK FOR SHORT IN SUB BUS 2 LINES (NO. 1 CAN JUNCTION CONNECTOR - NETWORK GATEWAY ECU)

D

16.CHECK FOR SHORT IN SUB BUS 2 LINE (NO. 2 CAN JUNCTION CONNECTOR - CAN JUNCTION TERMINAL)
3.CHECK FOR DTC OUTPUT
a.

Reconnect the cable to the negative (-) battery terminal.


b.

Connect the GTS to the DLC3.


c.

Turn the ignition switch to ON.


d.

Turn the GTS on.


e.

Clear the DTCs.

Body Electrical > Gateway > Clear DTCs
50002 150

f.

Turn the ignition switch off.


g.

Turn the ignition switch to ON.


h.

Check for DTCs.

Body Electrical > Gateway > Trouble Codes
50001 150

Result:
Result Proceed to
DTC U1002 is not output A
DTC U1002 is output B



A

B

4.CHECK FOR OPEN IN SUB BUS 2 MAIN LINES (NETWORK GATEWAY ECU)
a.
C238892
1.021,0.177 1.406,0.406 0.385,0.229 2.281,1.823 2.146,1.823 2.146,1.823 1.948,1.5 true 1.563,1.833 1.677,1.833 1.677,1.833 1.844,1.51 true 0.115,0.135 0.427,0.333 0.313,0.198 10 false *a 1.094,0.198 1.552,0.396 0.458,0.198 10 false F85 2.333,1.729 2.948,1.927 0.615,0.198 10 false CA2H 1.188,1.75 1.792,1.948 0.604,0.198 10 false CA2L
*a Front view of wire harness connector
(to Network Gateway ECU)


Disconnect the F85 network gateway ECU connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F85-13 (CA2H) - F85-12 (CA2L) Cable disconnected from negative (-) battery terminal 108 to 132 Ω



Result:
Result
OK
NG



OK

NG

5.CHECK FOR OPEN IN SUB BUS 2 MAIN LINES (CAN JUNCTION TERMINAL)
5.CHECK FOR OPEN IN SUB BUS 2 MAIN LINES (CAN JUNCTION TERMINAL)
a.

Reconnect the F85 network gateway ECU connector.


b.
C285690
1.49,0.219 1.958,0.531 0.469,0.313 1.208,1.802 1.354,1.802 1.354,1.802 1.781,1.24 true 2.51,1.781 2.385,1.781 2.385,1.781 2.052,1.26 true 0.115,0.094 0.427,0.292 0.313,0.198 10 false *a 1.573,0.292 2.188,0.49 0.615,0.198 10 false M42 0.833,1.719 1.448,1.917 0.615,0.198 10 false CANL 2.573,1.698 3.188,1.896 0.615,0.198 10 false CANH
*a Front view of wire harness connector
(to CAN Junction Terminal)


Disconnect the M42 CAN junction terminal connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M42-3 (CANH) - M42-2 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω



Result:
Result
OK
NG



OK

REPLACE CAN JUNCTION TERMINAL

NG

6.CHECK FOR OPEN IN SUB BUS 2 MAIN LINES (NO. 1 CAN JUNCTION CONNECTOR)
6.CHECK FOR OPEN IN SUB BUS 2 MAIN LINES (NO. 1 CAN JUNCTION CONNECTOR)
a.

Reconnect the M42 CAN junction terminal connector.


b.
C299838
2.74,1.604 3.146,1.885 0.406,0.281 1.542,1.615 1.948,1.896 0.406,0.281 2.958,2.948 2.896,2.948 2.896,2.948 2.823,2.51 true 1.74,2.948 1.677,2.948 1.677,2.948 1.604,2.51 true 1.24,2.677 1.302,2.677 1.302,2.677 1.5,2.438 true 2.458,2.677 2.521,2.677 2.521,2.677 2.719,2.438 true 1.74,2.458 1.354,2.25 1.354,2.25 1.281,2.25 true 1.74,2.333 1.323,1.885 1.323,1.885 1.26,1.885 true 2.948,2.313 2.656,1.885 2.656,1.885 2.604,1.885 true 2.948,2.458 2.688,2.24 2.688,2.24 2.625,2.24 true 0.052,0.042 0.365,0.24 0.313,0.198 10 false *a 2.792,1.646 3.156,1.854 0.365,0.208 10 false F104 1.594,1.656 1.958,1.865 0.365,0.208 10 false F105 3.01,2.865 3.167,3.063 0.156,0.198 10 false W 1.813,2.854 1.969,3.052 0.156,0.198 10 false W 2.198,2.583 2.51,2.781 0.313,0.198 10 false BR 1.094,2.594 1.25,2.792 0.156,0.198 10 false L 0.698,1.792 1.615,1.99 0.917,0.198 10 false CANH*c 0.719,2.156 1.635,2.354 0.917,0.198 10 false CANL*c 2.042,1.781 2.958,1.979 0.917,0.198 10 false CANH*b 2.083,2.146 3,2.344 0.917,0.198 10 false CANL*b
*a Rear view of wire harness connector
(to No. 1 CAN Junction Connector)
*b to No. 2 CAN Junction Connector
*c to Network Gateway ECU


Disconnect the F104 and F105 wire harness connectors.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to
F104-1 (CANH) - F104-2 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω No. 2 CAN junction connector
F105-1 (CANH) - F105-2 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω Network gateway ECU

Wiring Color:
Code Color (CANH Side) Color (CANL Side) Connected to
F104 BR W No. 2 CAN junction connector
F105 L W Network gateway ECU



NOTICE:
·

Before disconnecting the connectors, make a note of where they are connected.

·

Reconnect each connector to its original position.



Result:
Result Proceed to
OK A
NG (Network gateway ECU main line) B
NG (No. 2 CAN junction connector main line) C



A

REPLACE NO. 1 CAN JUNCTION CONNECTOR

B

REPAIR OR REPLACE CAN MAIN BUS LINE OR CONNECTOR (NETWORK GATEWAY ECU - NO. 1 CAN JUNCTION CONNECTOR)

C

7.CHECK FOR OPEN IN SUB BUS 2 MAIN LINES (NO. 2 CAN JUNCTION CONNECTOR)
7.CHECK FOR OPEN IN SUB BUS 2 MAIN LINES (NO. 2 CAN JUNCTION CONNECTOR)
a.

Reconnect the F104 and F105 wire harness connectors.


b.
C295404
0.396,1.667 0.802,1.948 0.406,0.281 1.406,1.646 1.813,1.927 0.406,0.281 0.427,2.438 0.375,2.021 0.375,2.021 0.292,2.021 false 0.635,3.083 0.542,3.083 0.542,3.083 0.458,2.573 true 0.823,2.104 0.781,2.104 0.781,2.104 0.594,2.375 true 0.833,2.302 0.781,2.302 0.781,2.302 0.594,2.521 true 1.188,2.625 1.26,2.625 1.26,2.625 1.396,2.531 false 1.479,2.583 1.604,3.063 1.604,3.063 1.698,3.063 true 1.854,2.094 1.813,2.094 1.813,2.094 1.625,2.365 true 1.875,2.292 1.823,2.292 1.823,2.292 1.635,2.51 true 0.083,0.083 0.396,0.281 0.313,0.198 10 false *a 0.938,2.531 1.25,2.729 0.313,0.198 10 false BR 0.688,2.979 0.844,3.177 0.156,0.198 10 false W 1.479,1.688 2.094,1.885 0.615,0.198 10 false M38 0.469,1.708 1.083,1.906 0.615,0.198 10 false M41 1.927,1.99 2.844,2.188 0.917,0.198 10 false CANH*b 1.958,2.198 2.875,2.396 0.917,0.198 10 false CANL*b 0.906,2.01 1.823,2.208 0.917,0.198 10 false CANH*c 1.76,2.969 1.917,3.167 0.156,0.198 10 false W 0.146,1.927 0.458,2.125 0.313,0.198 10 false B 0.906,2.208 1.823,2.406 0.917,0.198 10 false CANL*c
*a Rear view of wire harness connector
(to No. 2 CAN Junction Connector)
*b to No. 1 CAN Junction Connector
*c to CAN Junction Terminal


Disconnect the M38 and M41 wire harness connectors.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to
M38-1 (CANH) - M38-2 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω No. 1 CAN junction connector
M41-1 (CANH) - M41-2 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω CAN junction terminal

Wiring Color:
Code Color (CANH Side) Color (CANL Side) Connected to
M38 BR W No. 1 CAN junction connector
M41 B W CAN junction terminal



NOTICE:
·

Before disconnecting the connectors, make a note of where they are connected.

·

Reconnect each connector to its original position.



Result:
Result Proceed to
OK A
NG (No. 1 CAN junction connector main line) B
NG (CAN junction terminal main line) C



A

REPLACE NO. 2 CAN JUNCTION CONNECTOR

B

REPAIR OR REPLACE CAN MAIN BUS LINE OR CONNECTOR (NO. 1 CAN JUNCTION CONNECTOR - NO. 2 CAN JUNCTION CONNECTOR)

C

REPAIR OR REPLACE CAN MAIN BUS LINE OR CONNECTOR (NO. 2 CAN JUNCTION CONNECTOR - CAN JUNCTION TERMINAL)

8.CHECK FOR SHORT IN SUB BUS 2 LINES (NO. 1 CAN JUNCTION CONNECTOR - NETWORK GATEWAY ECU)
a.
C299839
2.344,1.667 2.771,1.938 0.427,0.271 1.979,2.813 2.031,2.813 2.031,2.813 2.323,2.458 false 2.563,2.854 2.51,2.854 2.51,2.854 2.417,2.521 true 2.042,1.813 2.104,1.813 2.104,1.813 2.552,2.323 true 2,2.219 2.073,2.219 2.073,2.219 2.563,2.469 true 0.094,0.063 0.406,0.26 0.313,0.198 10 false *a 2.406,1.708 2.813,1.917 0.406,0.208 10 false F105 2.625,2.75 2.781,2.948 0.156,0.198 10 false W 1.844,2.729 2,2.927 0.156,0.198 10 false L 1.479,1.719 2.396,1.917 0.917,0.198 10 false CANH*b 1.448,2.115 2.365,2.313 0.917,0.198 10 false CANL*b
*a Rear view of wire harness connector
(to No. 1 CAN Junction Connector)
*b to Network Gateway ECU


Disconnect the F105 wire harness connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F105-1 (CANH) - F105-2 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω



NOTICE:
·

Before disconnecting the connectors, make a note of where they are connected.

·

Reconnect each connector to its original position.



Result:
Result
OK
NG



OK

9.CHECK FOR SHORT IN SUB BUS 2 LINES (BRANCH LINE)

NG

15.CHECK FOR SHORT IN SUB BUS 2 LINES (NETWORK GATEWAY ECU)
9.CHECK FOR SHORT IN SUB BUS 2 LINES (BRANCH LINE)
a.

Reconnect the F105 wire harness connector.


b.
C299840
2.365,0.354 2.771,0.646 0.406,0.292 2.042,2.844 2.115,2.844 2.115,2.844 2.583,1.427 true 1.917,0.604 2,0.604 2,0.604 2.573,1.281 true 0.104,0.073 0.417,0.271 0.313,0.198 10 false *a 2.417,0.406 2.844,0.677 0.427,0.271 10 false F105 1.354,0.51 2.271,0.708 0.917,0.198 10 false CANH*b 1.49,2.75 2.406,2.948 0.917,0.198 10 false CANL*b
*a Rear view of wire harness connector
(to No. 1 CAN Junction Connector)
*b to Network Gateway ECU


Connect the probes of an ohmmeter to terminals 1 (CANH) and 2(CANL) of the network gateway ECU main line harness connector.


c.

While observing the resistance value shown on the tester, disconnect the F108, M39 and M40 connectors from the No. 1 CAN junction connector or No. 2 CAN junction connector one by one until the resistance becomes normal (between 54 and 69 Ω).

C299843
2.323,1.813 2.635,2.01 0.313,0.198 10 false *1 4.573,1.813 5.51,2.188 0.938,0.375 10 false *2 (*A) 1.542,3.99 2.083,4.417 0.542,0.427 10 false *3 (*B) 3.51,4.646 4.583,4.844 1.073,0.198 10 false *4 (*C) 5.677,4 5.99,4.198 0.313,0.198 10 false *5 3.406,0.49 3.719,0.688 0.313,0.198 10 false *6 3.458,6.115 3.771,6.313 0.313,0.198 10 false *7 2.073,1.271 2.229,1.469 0.156,0.198 10 false L 2.563,1.271 2.719,1.469 0.156,0.198 10 false W 4.458,1.25 4.615,1.448 0.156,0.198 10 false R 4.938,1.25 5.094,1.448 0.156,0.198 10 false W 6.188,2 6.5,2.198 0.313,0.198 10 false BR 6.792,2 6.948,2.198 0.156,0.198 10 false W 0.125,4.479 0.438,4.677 0.313,0.198 10 false BR 0.719,4.469 0.875,4.667 0.156,0.198 10 false W 1.438,4.552 2.208,5.146 0.771,0.594 10 false L 1.927,4.563 2.083,4.76 0.156,0.198 10 false Y 1.438,5.375 1.594,5.573 0.156,0.198 10 false B 1.917,5.375 2.073,5.573 0.156,0.198 10 false W 3.313,5.333 3.625,5.531 0.313,0.198 10 false GR 3.875,5.333 4.031,5.531 0.156,0.198 10 false W 5.448,5.042 5.604,5.24 0.156,0.198 10 false B 5.958,5.042 6.115,5.24 0.156,0.198 10 false W
*A w/ Lane Departure Alert System *B w/ Parking Assist Monitor System
*C w/ Blind Spot Monitor System - -
*1 Network Gateway ECU *2 Lane Departure Warning Camera
*3 Television Camera Assembly *4 Blind Spot Monitor Sensor LH
*5 CAN Junction Terminal *6 No. 1 CAN Junction Connector
*7 No. 2 CAN Junction Connector - -


C299841
2.323,0.427 2.635,0.625 0.313,0.198 10 false *a 3.552,2.302 4.167,2.5 0.615,0.198 10 false F104 3.552,2.583 4.167,2.781 0.615,0.198 10 false F105 3.552,2.844 4.167,3.042 0.615,0.198 10 false F108
*a Component without harness connected
(No. 1 CAN Junction Connector)
- -


Wiring Color:
No. 1 CAN Junction Connector Side Code Color (CANH Side) Color (CANL Side)
No. 2 CAN junction connector F104 BR W
Network gateway ECU F105 L W
Lane departure warning camera* F108 R W


*: w/ Lane Departure Alert System


C299848
3.573,3.417 4.031,3.615 0.458,0.198 10 false M38 2.333,0.417 2.646,0.615 0.313,0.198 10 false *a 3.573,3.698 4.031,3.896 0.458,0.198 10 false M39 3.573,3.979 4.031,4.177 0.458,0.198 10 false M40 3.573,4.25 4.031,4.448 0.458,0.198 10 false M41
*a Component without harness connected
(No. 2 CAN Junction Connector)
- -


Wiring Color:
No. 1 CAN Junction Connector Side Code Color (CANH Side) Color (CANL Side)
No. 1 CAN junction connector M38 BR W
Television camera assembly*1 M39 B W
Blind spot monitor sensor LH*2 M40 GR W
CAN junction terminal M41 B W


·

*1: w/ Parking Assist Monitor System

·

*2: w/ Blind Spot Monitor System


NOTICE:

Do not reconnect the disconnected connectors until this inspection is complete because there may be a short in 2 or more branch lines.



Result:
Result Proceed to
The resistance is still below 54 Ω when all the specified connectors are disconnected. (There are no shorts between a pair of branch lines.) A
The resistance becomes normal (between 54 and 69 Ω) when a connector is disconnected. (There is a short between one or more pairs of branch lines.) B


d.

When there is a short in one or more of the branch lines:

i.

Reconnect all of the connectors to the CAN junction connector, except for the one that was disconnected last (the short-circuited bus line). Check that the resistance shown on the tester is normal (between 54 and 69 Ω) to confirm that there is a short in the one branch line only.

HINT:
·

Connectors that connect to the CAN junction connector can be distinguished by the color of their CAN bus lines.

·

Reconnecting the connectors to non-original positions on the CAN junction connector does not affect system performance. However, it is preferred to reconnect the connectors to their original positions to avoid negative effects on the wiring such as tension on the wiring harnesses, and to make future maintenance easier.






A

10.CHECK FOR SHORT IN SUB BUS 2 LINES (NO. 2 CAN JUNCTION CONNECTOR - CAN JUNCTION TERMINAL)

B

14.CHECK FOR SHORT IN SUB BUS 2 LINES (ECU, SENSOR)
10.CHECK FOR SHORT IN SUB BUS 2 LINES (NO. 2 CAN JUNCTION CONNECTOR - CAN JUNCTION TERMINAL)
a.
C299832
0.396,1.677 0.771,1.938 0.375,0.26 0.417,2.448 0.365,2.229 0.365,2.229 0.313,2.229 false 0.615,3.031 0.542,3.031 0.542,3.031 0.458,2.573 true 0.594,2.375 1,1.958 1,1.958 1.073,1.958 true 0.583,2.521 0.917,2.604 0.917,2.604 1.01,2.604 true 0.094,0.094 0.406,0.292 0.313,0.198 10 false *a 0.458,1.729 0.917,1.927 0.458,0.198 10 false M41 0.167,2.125 0.323,2.323 0.156,0.198 10 false B 0.688,2.938 0.844,3.135 0.156,0.198 10 false W 1.156,1.865 2.073,2.063 0.917,0.198 10 false CANH*b 1.104,2.51 2.021,2.708 0.917,0.198 10 false CANL*b
*a Rear view of wire harness connector
(to No. 2 CAN Junction Connector)
*b to CAN Junction Terminal


Disconnect the M41 wire harness connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M41-1 (CANH) - M41-2 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω



NOTICE:
·

Before disconnecting the connectors, make a note of where they are connected.

·

Reconnect each connector to its original position.



Result:
Result
OK
NG



OK

11.CHECK FOR SHORT IN SUB BUS 2 LINES (NO. 1 CAN JUNCTION CONNECTOR)

NG

13.CHECK FOR SHORT IN SUB BUS 2 LINES (CAN JUNCTION TERMINAL)
11.CHECK FOR SHORT IN SUB BUS 2 LINES (NO. 1 CAN JUNCTION CONNECTOR)
a.
C299842
2.677,1.625 3.083,1.865 0.406,0.24 2.302,2.833 2.385,2.833 2.385,2.833 2.646,2.458 true 2.938,3 2.865,3 2.865,3 2.76,2.521 true 2.885,2.313 2.427,1.771 2.427,1.771 2.365,1.771 true 2.885,2.469 2.333,2.219 2.333,2.219 2.26,2.219 true 0.094,0.083 0.406,0.281 0.313,0.198 10 false *a 2.729,1.656 3.125,1.885 0.396,0.229 10 false F104 2.063,2.74 2.375,2.938 0.313,0.198 10 false BR 3,2.906 3.156,3.104 0.156,0.198 10 false W 1.802,1.667 2.719,1.865 0.917,0.198 10 false CANH*b 1.719,2.125 2.635,2.323 0.917,0.198 10 false CANL*b
*a Rear view of wire harness connector
(to No. 1 CAN Junction Connector)
*b to No. 2 CAN Junction Connector


Disconnect the F104 wire harness connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F104-1 (CANH) - F104-2 (CANL) Cable disconnected from negative (-) battery terminal 1 MΩ or higher



NOTICE:
·

Before disconnecting the connectors, make a note of where they are connected.

·

Reconnect each connector to its original position.



Result:
Result
OK
NG



OK

REPLACE NO. 1 CAN JUNCTION CONNECTOR

NG

12.CHECK FOR SHORT IN SUB BUS 2 LINES (NO. 1 CAN JUNCTION CONNECTOR - NO. 2 CAN JUNCTION CONNECTOR)
12.CHECK FOR SHORT IN SUB BUS 2 LINES (NO. 1 CAN JUNCTION CONNECTOR - NO. 2 CAN JUNCTION CONNECTOR)
a.
C299834
1.365,1.667 1.75,1.938 0.385,0.271 1.563,2.375 1.885,2.01 1.885,2.01 1.958,2.01 true 1.573,2.521 1.896,2.417 1.896,2.417 2,2.417 true 1.417,2.573 1.594,3.073 1.594,3.073 1.667,3.073 true 1.094,2.323 1.188,2.323 1.188,2.323 1.323,2.49 true 0.094,0.094 0.406,0.292 0.313,0.198 10 false *a 1.427,1.708 1.885,1.906 0.458,0.198 10 false M38 2.031,1.917 2.948,2.115 0.917,0.198 10 false CANH*b 2.083,2.323 3,2.521 0.917,0.198 10 false CANL*b 0.844,2.229 1.156,2.427 0.313,0.198 10 false BR 1.74,2.979 1.896,3.177 0.156,0.198 10 false W
*a Rear view of wire harness connector
(to No. 2 CAN Junction Connector)
*b to No. 1 CAN Junction Connector


Disconnect the M38 wire harness connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M38-1 (CANH) - M38-2 (CANL) Cable disconnected from negative (-) battery terminal 1 MΩ or higher



NOTICE:
·

Before disconnecting the connectors, make a note of where they are connected.

·

Reconnect each connector to its original position.



Result:
Result
OK
NG



OK

REPLACE NO. 2 CAN JUNCTION CONNECTOR

NG

REPAIR OR REPLACE CAN MAIN BUS LINE OR CONNECTOR (NO. 1 CAN JUNCTION CONNECTOR - NO. 2 CAN JUNCTION CONNECTOR)

13.CHECK FOR SHORT IN SUB BUS 2 LINES (CAN JUNCTION TERMINAL)
a.

Reconnect the M41 wire harness connector.


b.
C292413C01
1.479,0.292 1.875,0.615 0.396,0.323 1.25,1.865 1.396,1.865 1.396,1.865 1.771,1.198 true 2.438,1.844 2.313,1.844 2.313,1.844 2.042,1.198 true 0.063,0.063 0.375,0.26 0.313,0.198 10 false *a 1.542,0.354 2.156,0.552 0.615,0.198 10 false M42 0.844,1.771 1.458,1.969 0.615,0.198 10 false CANL 2.5,1.75 3.115,1.948 0.615,0.198 10 false CANH
*a Front view of wire harness connector
(to CAN Junction Terminal)


Disconnect the M42 CAN junction terminal connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M42-3 (CANH) - M42-2 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω



Result:
Result
OK
NG



OK

REPLACE CAN JUNCTION TERMINAL

NG

REPAIR OR REPLACE CAN MAIN BUS LINE OR CONNECTOR (NO. 2 CAN JUNCTION CONNECTOR - CAN JUNCTION TERMINAL)

14.CHECK FOR SHORT IN SUB BUS 2 LINES (ECU, SENSOR)
a.

Reconnect all wire harness connectors (No. 1 CAN junction connector and No. 2 CAN junction connector).


b.
C242747
1.469,0.396 1.875,0.625 0.406,0.229 1.542,1.083 1.188,1.531 1.188,1.531 1.073,1.531 true 1.625,1.083 1.375,1.792 1.375,1.792 1.26,1.792 true 0.083,0.063 0.396,0.219 0.313,0.156 10 false *a 1.552,0.417 2.063,0.688 0.51,0.271 10 false F85 0.688,1.438 1.146,1.625 0.458,0.188 10 false CA2H 0.896,1.708 1.344,1.885 0.448,0.177 10 false CA2L
*a Component with harness connected
(Network Gateway ECU)


Disconnect the connector that includes terminals CANH and CANL from the ECU or sensor to which the short-circuited branch line is connected.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>TERMINALS OF ECU


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F85-13 (CA2H) - F85-12 (CA2L) Cable disconnected from negative (-) battery terminal 54 to 69 Ω


HINT:
·

If the resistance becomes normal (between 54 and 69 Ω) when the connector is disconnected from the ECU or sensor, there may be a short in the ECU or sensor.

·

If the resistance does not become normal (between 54 and 69 Ω) when the connector is disconnected from the ECU or sensor, repair or replace the short-circuited branch line or connector.




Result:
Result
OK
NG



OK

REPLACE CORRESPONDING ECU OR SENSOR

NG

REPAIR OR REPLACE CORRESPONDING ECU OR SENSOR BUS LINES OR CONNECTOR

15.CHECK FOR SHORT IN SUB BUS 2 LINES (NETWORK GATEWAY ECU)
a.

Reconnect the F105 wire harness connector.


b.
C292378
0.823,0.281 1.24,0.573 0.417,0.292 1.292,1.958 1.406,1.958 1.406,1.958 1.833,1.469 true 2.458,1.927 2.354,1.927 2.354,1.927 1.948,1.458 true 0.083,0.073 0.396,0.271 0.313,0.198 10 false *a 0.906,0.333 1.365,0.531 0.458,0.198 10 false F85 0.906,1.875 1.521,2.073 0.615,0.198 10 false CA2L 2.531,1.833 3.146,2.031 0.615,0.198 10 false CA2H
*a Front view of wire harness connector
(to Network Gateway ECU)


Disconnect the F85 network gateway ECU connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F85-13 (CA2H) - F85-12 (CA2L) Cable disconnected from negative (-) battery terminal 108 to 132 Ω



Result:
Result
OK
NG



OK

NG

REPAIR OR REPLACE CAN MAIN BUS LINE OR CONNECTOR (NETWORK GATEWAY ECU - NO. 1 CAN JUNCTION CONNECTOR)

16.CHECK FOR SHORT IN SUB BUS 2 LINE (NO. 2 CAN JUNCTION CONNECTOR - CAN JUNCTION TERMINAL)
a.
C299835
0.365,1.396 0.75,1.646 0.385,0.25 0.292,3.625 0.688,3.875 0.396,0.25 1.635,3.469 2.021,3.021 2.021,3.021 2.125,3.021 true 2.365,3.917 1.99,4.385 1.99,4.385 1.896,4.385 true 0.375,2.063 0.24,1.656 0.24,1.656 0.177,1.656 true 0.646,2.667 0.583,2.667 0.583,2.667 0.417,2.188 true 0.563,2 0.885,1.698 0.885,1.698 0.99,1.698 true 0.563,2.146 0.875,2.26 0.875,2.26 0.948,2.26 true 0.052,0.042 0.365,0.24 0.313,0.198 10 false *a 0.417,1.427 0.875,1.625 0.458,0.198 10 false M41 0.375,3.656 0.833,3.854 0.458,0.198 10 false F25 0.49,3.135 0.802,3.333 0.313,0.198 10 false *1 2.219,2.927 2.531,3.125 0.313,0.198 10 false CG 1.573,4.281 2.031,4.479 0.458,0.198 10 false BAT 0.031,1.563 0.188,1.76 0.156,0.198 10 false B 0.708,2.583 0.865,2.781 0.156,0.198 10 false W 1.073,1.604 1.99,1.802 0.917,0.198 10 false CANH*b 1.031,2.167 1.948,2.365 0.917,0.198 10 false CANL*b
*1 DLC3
*a Rear view of wire harness connector
(to No. 2 CAN Junction Connector)
*b to CAN Junction Terminal


Disconnect the M41 wire harness connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Result
M41-1 (CANH) - F25-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher Below 200 Ω: CANH ground short
M41-2 (CANL) - F25-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher Below 200 Ω: CANL ground short
M41-1 (CANH) - F25-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher Below 6 kΩ: CANH +B short
M41-2 (CANL) - F25-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher Below 6 kΩ: CANL +B short



NOTICE:
·

Before disconnecting the connectors, make a note of where they are connected.

·

Reconnect each connector to its original position.



HINT:
·

It is only necessary to perform the inspection in the above table for the result (short circuit) that was obtained in the Check Sub Bus 2 inspection.

·

Find the necessary inspection from the Purpose column that matches the result in the Result column from the Check Sub Bus 2 inspection.



Result:
Result
OK
NG



OK

17.CHECK FOR SHORT IN SUB BUS 2 LINE

NG

21.CHECK FOR SHORT IN SUB BUS 2 LINE (CAN JUNCTION TERMINAL)
17.CHECK FOR SHORT IN SUB BUS 2 LINE
a.

Reconnect the M41 wire harness connector.


b.
C295426
0.25,3.615 0.635,3.927 0.385,0.313 0.375,0.375 0.75,0.635 0.375,0.26 1.646,3.469 1.896,3.052 1.896,3.052 2.063,3.052 true 2.354,3.948 2.125,4.354 2.125,4.354 1.979,4.354 true 0.563,1.365 1,0.833 1,0.833 1.156,0.833 true 0.563,1.521 1.063,2.375 1.063,2.375 1.135,2.375 true 0.229,0.948 0.281,0.948 0.281,0.948 0.344,1.479 true 0.427,1.563 0.542,2.396 0.542,2.396 0.615,2.396 true 0.083,0.188 0.396,0.385 0.313,0.198 10 false *a 0.5,2.99 0.813,3.188 0.313,0.198 10 false *1 0.313,3.667 0.625,3.865 0.313,0.198 10 false F25 2.135,2.958 2.448,3.156 0.313,0.198 10 false CG 1.667,4.26 2.125,4.458 0.458,0.198 10 false BAT 0.438,0.417 1.052,0.615 0.615,0.198 10 false M41 1.24,0.74 1.854,0.938 0.615,0.198 10 false CANH 1.208,2.281 1.823,2.479 0.615,0.198 10 false CANL 0.698,2.302 0.854,2.5 0.156,0.198 10 false W 0.083,0.844 0.24,1.042 0.156,0.198 10 false B
*1 DLC3
*a Rear view of wire harness connector
(to No. 2 CAN Junction Connector)


Connect the probes of an ohmmeter to terminals 1 (CANH) and 2 (CANL) of the M41 wire harness connector and CG or BAT of the DLC3.

HINT:

It is only necessary to perform the inspection for the result (short circuit) that was obtained in the Check Sub Bus 2 inspection.



c.

While observing the resistance value shown on the ohmmeter, disconnect the F105, F108, M39 and M40 connectors from the No. 1 CAN junction connector and No. 2 CAN junction connector until the resistance becomes normal (6 kΩ or higher (for +B short) or 200 Ω or higher (for ground short)).

C299843
2.323,1.813 2.635,2.01 0.313,0.198 10 false *1 4.573,1.813 5.51,2.188 0.938,0.375 10 false *2 (*A) 1.542,3.99 2.083,4.417 0.542,0.427 10 false *3 (*B) 3.51,4.646 4.583,4.844 1.073,0.198 10 false *4 (*C) 5.677,4 5.99,4.198 0.313,0.198 10 false *5 3.406,0.49 3.719,0.688 0.313,0.198 10 false *6 3.458,6.115 3.771,6.313 0.313,0.198 10 false *7 2.073,1.271 2.229,1.469 0.156,0.198 10 false L 2.563,1.271 2.719,1.469 0.156,0.198 10 false W 4.458,1.25 4.615,1.448 0.156,0.198 10 false R 4.938,1.25 5.094,1.448 0.156,0.198 10 false W 6.188,2 6.5,2.198 0.313,0.198 10 false BR 6.792,2 6.948,2.198 0.156,0.198 10 false W 0.125,4.479 0.438,4.677 0.313,0.198 10 false BR 0.719,4.469 0.875,4.667 0.156,0.198 10 false W 1.438,4.552 2.208,5.146 0.771,0.594 10 false L 1.927,4.563 2.083,4.76 0.156,0.198 10 false Y 1.438,5.375 1.594,5.573 0.156,0.198 10 false B 1.917,5.375 2.073,5.573 0.156,0.198 10 false W 3.313,5.333 3.625,5.531 0.313,0.198 10 false GR 3.875,5.333 4.031,5.531 0.156,0.198 10 false W 5.448,5.042 5.604,5.24 0.156,0.198 10 false B 5.958,5.042 6.115,5.24 0.156,0.198 10 false W
*A w/ Lane Departure Alert System *B w/ Parking Assist Monitor System
*C w/ Blind Spot Monitor System - -
*1 Network Gateway ECU *2 Lane Departure Warning Camera
*3 Television Camera Assembly *4 Blind Spot Monitor Sensor LH
*5 CAN Junction Terminal *6 No. 1 CAN Junction Connector
*7 No. 2 CAN Junction Connector - -


C299841
2.323,0.427 2.635,0.625 0.313,0.198 10 false *a 3.552,2.302 4.167,2.5 0.615,0.198 10 false F104 3.552,2.583 4.167,2.781 0.615,0.198 10 false F105 3.552,2.844 4.167,3.042 0.615,0.198 10 false F108
*a Component without harness connected
(No. 1 CAN Junction Connector)
- -


Wiring Color:
No. 1 CAN Junction Connector Side Code Color (CANH Side) Color (CANL Side)
No. 2 CAN junction connector F104 BR W
Network gateway ECU F105 L W
Lane departure warning camera* F108 R W


*: w/ Lane Departure Alert System


C299848
3.573,3.417 4.031,3.615 0.458,0.198 10 false M38 2.333,0.417 2.646,0.615 0.313,0.198 10 false *a 3.573,3.698 4.031,3.896 0.458,0.198 10 false M39 3.573,3.979 4.031,4.177 0.458,0.198 10 false M40 3.573,4.25 4.031,4.448 0.458,0.198 10 false M41
*a Component without harness connected
(No. 2 CAN Junction Connector)
- -


Wiring Color:
No. 1 CAN Junction Connector Side Code Color (CANH Side) Color (CANL Side)
No. 1 CAN junction connector M38 BR W
Television camera assembly*1 M39 B W
Blind spot monitor sensor LH*2 M40 GR W
CAN junction terminal M41 B W


·

*1: w/ Parking Assist Monitor System

·

*2: w/ Blind Spot Monitor System



Result:
Result Proceed to
The resistance between terminals CANH and BAT, or the resistance between terminals CANL and BAT is still below 6 kΩ when all the specified connectors are disconnected from the CAN junction connector.
(There is a short to +B in the CAN main bus lines between the No. 1 CAN junction connector and No. 2 CAN junction connector.)
A
The resistance between terminals CANH and GND, or the resistance between terminals CANL and GND is still below 200 Ω when all the specified connectors are disconnected from the CAN junction connector.
(There is a short to GND in the CAN main bus lines between the No. 1 CAN junction connector and No. 2 CAN junction connector.)
The resistance between terminals CANH and BAT, or the resistance between terminals CANL and BAT becomes normal (6 kΩ or higher) when a connector is disconnected from the CAN junction connector.
(There is a short to +B in one of the areas that relate to one or more of the disconnected bus lines.)
B
The resistance between terminals CANH and GND, or the resistance between terminals CANL and GND becomes normal (200 Ω or higher) when a connector is disconnected from the CAN junction connector.
(There is a short to GND in one of the areas that relate to the disconnected bus lines.)



A

18.CHECK FOR SHORT IN SUB BUS 2 LINE (NO. 2 CAN JUNCTION CONNECTOR)

B

20.CHECK FOR SHORT IN SUB BUS 2 LINE (ECU, SENSOR)
18.CHECK FOR SHORT IN SUB BUS 2 LINE (NO. 2 CAN JUNCTION CONNECTOR)
a.

Reconnect all wire harness connectors (No. 1 CAN junction connector and No. 2 CAN junction connector).


b.

Disconnect the M38 wire harness connector.


c.
C299836
0.365,0.26 0.76,0.542 0.396,0.281 0.292,3.604 0.667,3.854 0.375,0.25 0.563,1.135 1.073,0.281 1.073,0.281 1.167,0.281 true 0.552,1.292 1.198,0.625 1.198,0.625 1.271,0.625 true 0.688,2.167 0.615,2.167 0.615,2.167 0.427,1.333 true 0.229,0.667 0.281,0.667 0.281,0.667 0.344,1.24 true 1.646,3.438 1.99,3.052 1.99,3.052 2.094,3.052 true 2.354,3.938 1.969,4.396 1.969,4.396 1.885,4.396 true 0.073,0.073 0.385,0.271 0.313,0.198 10 false *a 0.438,0.313 0.896,0.51 0.458,0.198 10 false M41 1.24,0.188 2.156,0.385 0.917,0.198 10 false CANH*b 1.344,0.531 2.26,0.729 0.917,0.198 10 false CANL*b 0.781,2.063 0.938,2.26 0.156,0.198 10 false W 0.094,0.563 0.25,0.76 0.156,0.198 10 false B 0.448,2.948 0.76,3.146 0.313,0.198 10 false *1 0.365,3.635 0.823,3.833 0.458,0.198 10 false F25 2.188,2.958 2.5,3.156 0.313,0.198 10 false CG 1.573,4.292 2.031,4.49 0.458,0.198 10 false BAT
*1 DLC3
*a Rear view of wire harness connector
(to No. 2 CAN Junction Connector)
*b to CAN Junction Terminal


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Result
M41-1 (CANH) - F25-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher Below 200 Ω: CANH ground short
M41-2 (CANL) - F25-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher Below 200 Ω: CANL ground short
M41-1 (CANH) - F25-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher Below 6 kΩ: CANH +B short
M41-2 (CANL) - F25-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher Below 6 kΩ: CANL +B short



NOTICE:
·

Before disconnecting the connectors, make a note of where they are connected.

·

Reconnect each connector to its original position.



HINT:
·

It is only necessary to perform the inspection in the above table for the result (short circuit) that was obtained in the Check Sub Bus 2 inspection.

·

Find the necessary inspection from the Purpose column that matches the result in the Result column from the Check Sub Bus 2 inspection.



Result:
Result
OK
NG



OK

19.CHECK FOR SHORT IN SUB BUS 2 LINE (NO. 1 CAN JUNCTION CONNECTOR)

NG

REPLACE NO. 2 CAN JUNCTION CONNECTOR

19.CHECK FOR SHORT IN SUB BUS 2 LINE (NO. 1 CAN JUNCTION CONNECTOR)
a.

Reconnect the M38 wire harness connector.


b.

Disconnect the F104 wire harness connector.


c.
C295426
0.25,3.615 0.625,3.948 0.375,0.333 0.375,0.385 0.76,0.625 0.385,0.24 1.646,3.469 1.896,3.052 1.896,3.052 2.063,3.052 true 2.354,3.948 2.125,4.354 2.125,4.354 1.979,4.354 true 0.563,1.354 1,0.823 1,0.823 1.156,0.823 true 0.563,1.531 0.979,2.323 0.979,2.323 1.063,2.323 true 0.198,0.781 0.25,0.781 0.25,0.781 0.365,1.448 true 0.427,1.563 0.542,2.396 0.542,2.396 0.615,2.396 true 0.094,0.219 0.406,0.417 0.313,0.198 10 false *a 0.5,2.99 0.813,3.188 0.313,0.198 10 false *1 0.323,3.667 0.635,3.865 0.313,0.198 10 false F25 2.135,2.958 2.448,3.156 0.313,0.198 10 false CG 1.667,4.26 2.125,4.458 0.458,0.198 10 false BAT 0.438,0.406 1.052,0.604 0.615,0.198 10 false M41 1.24,0.729 1.854,0.927 0.615,0.198 10 false CANH*b 1.135,2.229 1.75,2.427 0.615,0.198 10 false CANL*b 0.688,2.302 0.844,2.5 0.156,0.198 10 false W 0.052,0.677 0.208,0.875 0.156,0.198 10 false B
*1 DLC3
*a Rear view of wire harness connector
(to No. 2 CAN Junction Connector)
*b to CAN Junction Terminal


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Result
M41-1 (CANH) - F25-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher Below 200 Ω: CANH ground short
M41-2 (CANL) - F25-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher Below 200 Ω: CANL ground short
M41-1 (CANH) - F25-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher Below 6 kΩ: CANH +B short
M41-2 (CANL) - F25-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher Below 6 kΩ: CANL +B short



NOTICE:
·

Before disconnecting the connectors, make a note of where they are connected.

·

Reconnect each connector to its original position.



HINT:
·

It is only necessary to perform the inspection in the above table for the result (short circuit) that was obtained in the Check Sub Bus 2 inspection.

·

Find the necessary inspection from the Purpose column that matches the result in the Result column from the Check Sub Bus 2 inspection.



Result:
Result
OK
NG



OK

REPLACE NO. 1 CAN JUNCTION CONNECTOR

NG

REPAIR OR REPLACE CAN MAIN BUS LINE OR CONNECTOR (NO. 1 CAN JUNCTION CONNECTOR - NO. 2 CAN JUNCTION CONNECTOR)

20.CHECK FOR SHORT IN SUB BUS 2 LINE (ECU, SENSOR)
a.

Reconnect all wire harness connectors (No. 1 CAN junction connector and No. 2 CAN junction connector).


b.

Disconnect the connector that includes terminals CANH and CANL from the ECU or sensor to which the bus line shorted to +B or shorted to GND is connected.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>TERMINALS OF ECU


c.
C295426
0.25,3.615 0.635,3.927 0.385,0.313 0.375,0.375 0.75,0.635 0.375,0.26 1.646,3.469 1.896,3.052 1.896,3.052 2.063,3.052 true 2.354,3.948 2.125,4.354 2.125,4.354 1.979,4.354 true 0.563,1.365 1,0.833 1,0.833 1.156,0.833 true 0.563,1.521 1.063,2.375 1.063,2.375 1.135,2.375 true 0.229,0.948 0.281,0.948 0.281,0.948 0.344,1.479 true 0.427,1.563 0.542,2.396 0.542,2.396 0.615,2.396 true 0.083,0.188 0.396,0.385 0.313,0.198 10 false *a 0.5,2.99 0.813,3.188 0.313,0.198 10 false *1 0.313,3.667 0.625,3.865 0.313,0.198 10 false F25 2.135,2.958 2.448,3.156 0.313,0.198 10 false CG 1.667,4.26 2.125,4.458 0.458,0.198 10 false BAT 0.438,0.417 1.052,0.615 0.615,0.198 10 false M41 1.24,0.74 1.854,0.938 0.615,0.198 10 false CANH 1.208,2.281 1.823,2.479 0.615,0.198 10 false CANL 0.698,2.302 0.854,2.5 0.156,0.198 10 false W 0.083,0.844 0.24,1.042 0.156,0.198 10 false B
*1 DLC3
*a Rear view of wire harness connector
(to No. 2 CAN Junction Connector)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Result
M41-1 (CANH) - F25-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher Below 200 Ω: CANH ground short
M41-2 (CANL) - F25-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher Below 200 Ω: CANL ground short
M41-1 (CANH) - F25-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher Below 6 kΩ: CANH +B short
M41-2 (CANL) - F25-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher Below 6 kΩ: CANH +B short


HINT:
·

It is only necessary to perform the inspection in the above table for the result (short circuit) that was obtained in the Check Sub Bus 2 inspection.

·

If the resistance becomes normal when the connector is disconnected from the ECU, there may be a short in the ECU.

·

Find the necessary inspection from the Purpose column that matches the result in the Result column from the Check Sub Bus 2 inspection.




Result:
Result
OK
NG



OK

REPLACE CORRESPONDING ECU OR SENSOR

NG

REPAIR OR REPLACE CORRESPONDING ECU OR SENSOR BUS LINES OR CONNECTOR

21.CHECK FOR SHORT IN SUB BUS 2 LINE (CAN JUNCTION TERMINAL)
a.

Reconnect the M41 wire harness connector.


b.

Disconnect the M42 CAN junction terminal connector.


c.
C287171
1.5,0.26 1.938,0.573 0.438,0.313 1.521,2.635 1.958,2.927 0.438,0.292 1.625,3.542 2.104,3.094 2.104,3.094 2.281,3.094 true 1.771,4.479 1.917,4.479 1.917,4.479 2.323,4.094 true 1.115,2.26 1.26,2.26 1.26,2.26 1.781,1.563 true 2.552,2.24 2.385,2.24 2.385,2.24 2.021,1.573 true 0.115,0.094 0.427,0.292 0.313,0.198 10 false *a 0.156,2.51 0.469,2.708 0.313,0.198 10 false *1 1.583,0.313 2.198,0.51 0.615,0.198 10 false M42 1.625,2.677 1.938,2.875 0.313,0.198 10 false F25 2.344,3.01 2.656,3.208 0.313,0.198 10 false CG 1.469,4.396 1.927,4.594 0.458,0.198 10 false BAT 0.719,2.177 1.333,2.375 0.615,0.198 10 false CANL 2.604,2.146 3.219,2.344 0.615,0.198 10 false CANH
*1 DLC3
*a Front view of wire harness connector
(to CAN Junction Terminal)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Result
M42-3 (CANH) - F25-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher Below 200 Ω: CANH ground short
M42-2 (CANL) - F25-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher Below 200 Ω: CANL ground short
M42-3 (CANH) - F25-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher Below 6 kΩ: CANH +B short
M42-2 (CANL) - F25-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher Below 6 kΩ: CANL +B short



HINT:
·

It is only necessary to perform the inspection in the above table for the result (short circuit) that was obtained in the Check Sub Bus 2 inspection.

·

Find the necessary inspection from the Purpose column that matches the result in the Result column from the Check Sub Bus 2 inspection.



Result:
Result
OK
NG



OK

REPLACE CAN JUNCTION TERMINAL

NG

REPAIR OR REPLACE CAN MAIN BUS LINE OR CONNECTOR (NO. 2 CAN JUNCTION CONNECTOR - CAN JUNCTION TERMINAL)

22.CHECK SUB BUS 2
a.

Disconnect the cable from the negative (-) battery terminal.


b.
C242747
1.458,0.177 1.885,0.448 0.427,0.271 0.854,1.635 0.969,1.635 0.969,1.635 1.542,1.083 true 1.021,1.865 1.104,1.865 1.104,1.865 1.625,1.083 true 1.385,0.948 1.104,0.531 1.104,0.531 1.01,0.531 true 2.042,0.938 2.354,0.531 2.354,0.531 2.458,0.531 true 0.104,0.073 0.417,0.271 0.313,0.198 10 false *a 1.542,0.219 2,0.417 0.458,0.198 10 false F85 0.458,1.542 1.073,1.74 0.615,0.198 10 false CA2H 0.656,1.771 1.271,1.969 0.615,0.198 10 false CA2L 0.677,0.448 1.135,0.646 0.458,0.198 10 false GND 2.51,0.438 3.125,0.635 0.615,0.198 10 false BATT
*a Component with harness connected
(Network Gateway ECU)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Result
F85-13 (CA2H) - F85-12 (CA2L) Cable disconnected from negative (-) battery terminal 54 to 69 Ω Below 54 Ω: Short circuit between bus lines
70 Ω or higher: Open circuit in a main bus line
F85-13 (CA2H) - F85-4 (GND) Cable disconnected from negative (-) battery terminal 200 Ω or higher Below 200 Ω: CANH ground short
F85-12 (CA2L) - F85-4 (GND) Cable disconnected from negative (-) battery terminal 200 Ω or higher Below 200 Ω: CANL ground short
F85-13 (CA2H) - F85-2 (BATT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher Below 6 kΩ: CANH +B short
F85-12 (CA2L) - F85-2 (BATT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher Below 6 kΩ: CANL +B short



Result:
Result Proceed to
OK A
Open circuit in CAN main bus line B
Short circuit between bus lines C
·

Ground short

·

+B short


D



A

23.CHECK FOR DTC OUTPUT

B

24.CHECK FOR OPEN IN SUB BUS 2 MAIN LINES (NETWORK GATEWAY ECU)

C

28.CHECK FOR SHORT IN SUB BUS 2 LINES (NO. 1 CAN JUNCTION CONNECTOR - NETWORK GATEWAY ECU)

D

36.CHECK FOR SHORT IN SUB BUS 2 LINE (NO. 2 CAN JUNCTION CONNECTOR - CAN JUNCTION TERMINAL)
23.CHECK FOR DTC OUTPUT
a.

Reconnect the cable to the negative (-) battery terminal.


b.

Connect the GTS to the DLC3.


c.

Turn the ignition switch to ON.


d.

Turn the GTS on.


e.

Clear the DTCs.

Body Electrical > Gateway > Clear DTCs
50002 150

f.

Turn the ignition switch off.


g.

Turn the ignition switch to ON.


h.

Check for DTCs.

Body Electrical > Gateway > Trouble Codes
50001 150

Result:
Result Proceed to
DTC U1002 is not output A
DTC U1002 is output B



A

B

24.CHECK FOR OPEN IN SUB BUS 2 MAIN LINES (NETWORK GATEWAY ECU)
a.
C238892
1.021,0.177 1.406,0.406 0.385,0.229 2.281,1.823 2.146,1.823 2.146,1.823 1.948,1.5 true 1.563,1.833 1.677,1.833 1.677,1.833 1.844,1.51 true 0.115,0.135 0.427,0.333 0.313,0.198 10 false *a 1.094,0.198 1.552,0.396 0.458,0.198 10 false F85 2.333,1.729 2.948,1.927 0.615,0.198 10 false CA2H 1.188,1.75 1.792,1.948 0.604,0.198 10 false CA2L
*a Front view of wire harness connector
(to Network Gateway ECU)


Disconnect the F85 network gateway ECU connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F85-13 (CA2H) - F85-12 (CA2L) Cable disconnected from negative (-) battery terminal 108 to 132 Ω



Result:
Result
OK
NG



OK

NG

25.CHECK FOR OPEN IN SUB BUS 2 MAIN LINES (CAN JUNCTION TERMINAL)
25.CHECK FOR OPEN IN SUB BUS 2 MAIN LINES (CAN JUNCTION TERMINAL)
a.

Reconnect the F85 network gateway ECU connector.


b.
C285690
1.479,0.219 1.927,0.51 0.448,0.292 1.208,1.802 1.354,1.802 1.354,1.802 1.781,1.24 true 2.51,1.781 2.385,1.781 2.385,1.781 2.052,1.26 true 0.115,0.094 0.427,0.292 0.313,0.198 10 false *a 1.563,0.271 2.177,0.469 0.615,0.198 10 false M42 0.833,1.719 1.448,1.917 0.615,0.198 10 false CANL 2.573,1.698 3.188,1.896 0.615,0.198 10 false CANH
*a Front view of wire harness connector
(to CAN Junction Terminal)


Disconnect the M42 CAN junction terminal connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M42-3 (CANH) - M42-2 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω



Result:
Result
OK
NG



OK

REPLACE CAN JUNCTION TERMINAL

NG

26.CHECK FOR OPEN IN SUB BUS 2 MAIN LINES (NO. 1 CAN JUNCTION CONNECTOR)
26.CHECK FOR OPEN IN SUB BUS 2 MAIN LINES (NO. 1 CAN JUNCTION CONNECTOR)
a.

Reconnect the M42 CAN junction terminal connector.


b.
C299844
1.083,1.688 1.5,1.927 0.417,0.24 2.104,1.698 2.521,1.938 0.417,0.24 2.313,2.375 2.667,2 2.667,2 2.74,2 true 2.313,2.521 2.604,2.646 2.604,2.646 2.698,2.646 true 2.167,2.573 2.302,3.052 2.302,3.052 2.375,3.052 true 2.115,2.448 2.031,2.177 2.031,2.177 1.969,2.177 true 1.323,3.094 1.26,3.094 1.26,3.094 1.156,2.563 true 1.042,2.51 0.844,2.719 0.844,2.719 0.781,2.719 true 1.271,2.375 0.917,1.854 0.917,1.854 0.865,1.854 true 1.281,2.521 0.979,2.24 0.979,2.24 0.917,2.24 true 0.083,0.052 0.396,0.25 0.313,0.198 10 false *a 2.156,1.719 2.771,1.917 0.615,0.198 10 false F104 1.135,1.719 1.75,1.917 0.615,0.198 10 false F105 2.448,2.958 2.604,3.156 0.156,0.198 10 false W 0.646,2.625 0.802,2.823 0.156,0.198 10 false L 1.729,2.083 2.042,2.281 0.313,0.198 10 false BR 2.813,1.906 3.396,2.156 0.583,0.25 10 false CANH*b 2.781,2.552 3.365,2.802 0.583,0.25 10 false CANL*b 1.396,3 1.552,3.198 0.156,0.198 10 false W 0.302,1.76 0.885,2.01 0.583,0.25 10 false CANH*c 0.354,2.146 0.938,2.396 0.583,0.25 10 false CANL*c
*a Rear view of wire harness connector
(to No. 1 CAN Junction Connector)
*b to No. 2 CAN Junction Connector
*c to Network Gateway ECU


Disconnect the F104 and F105 wire harness connectors.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to
F104-1 (CANH) - F104-2 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω No. 2 CAN junction connector
F105-1 (CANH) - F105-2 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω Network gateway ECU

Wiring Color:
Code Color (CANH Side) Color (CANL Side) Connected to
F104 BR W No. 2 CAN junction connector
F105 L W Network gateway ECU



NOTICE:
·

Before disconnecting the connectors, make a note of where they are connected.

·

Reconnect each connector to its original position.



Result:
Result Proceed to
OK A
NG (Network gateway ECU main line) B
NG (No. 2 CAN junction connector main line) C



A

REPLACE NO. 1 CAN JUNCTION CONNECTOR

B

REPAIR OR REPLACE CAN MAIN BUS LINE OR CONNECTOR (NETWORK GATEWAY ECU - NO. 1 CAN JUNCTION CONNECTOR)

C

27.CHECK FOR OPEN IN SUB BUS 2 MAIN LINES (NO. 2 CAN JUNCTION CONNECTOR)
27.CHECK FOR OPEN IN SUB BUS 2 MAIN LINES (NO. 2 CAN JUNCTION CONNECTOR)
a.

Reconnect the F104 and F105 wire harness connectors.


b.
C295404
0.396,1.667 0.802,1.948 0.406,0.281 1.406,1.646 1.813,1.927 0.406,0.281 0.427,2.438 0.375,2.021 0.375,2.021 0.292,2.021 false 0.635,3.083 0.542,3.083 0.542,3.083 0.458,2.573 true 0.823,2.104 0.781,2.104 0.781,2.104 0.594,2.375 true 0.833,2.302 0.781,2.302 0.781,2.302 0.594,2.521 true 1.188,2.625 1.26,2.625 1.26,2.625 1.396,2.531 false 1.479,2.583 1.604,3.063 1.604,3.063 1.698,3.063 true 1.854,2.094 1.813,2.094 1.813,2.094 1.625,2.365 true 1.875,2.292 1.823,2.292 1.823,2.292 1.635,2.51 true 0.083,0.083 0.396,0.281 0.313,0.198 10 false *a 0.938,2.531 1.25,2.729 0.313,0.198 10 false BR 0.688,2.979 0.844,3.177 0.156,0.198 10 false W 1.479,1.688 2.094,1.885 0.615,0.198 10 false M38 0.469,1.708 1.083,1.906 0.615,0.198 10 false M41 1.927,1.99 2.844,2.188 0.917,0.198 10 false CANH*b 1.958,2.198 2.875,2.396 0.917,0.198 10 false CANL*b 0.906,2.01 1.823,2.208 0.917,0.198 10 false CANH*c 1.76,2.969 1.917,3.167 0.156,0.198 10 false W 0.146,1.927 0.458,2.125 0.313,0.198 10 false B 0.906,2.208 1.823,2.406 0.917,0.198 10 false CANL*c
*a Rear view of wire harness connector
(to No. 2 CAN Junction Connector)
*b to No. 1 CAN Junction Connector
*c to CAN Junction Terminal


Disconnect the M38 and M41 wire harness connectors.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to
M38-1 (CANH) - M38-2 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω No. 1 CAN junction connector
M41-1 (CANH) - M41-2 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω CAN junction terminal

Wiring Color:
Code Color (CANH Side) Color (CANL Side) Connected to
M38 BR W No. 1 CAN junction connector
M41 B W CAN junction terminal



NOTICE:
·

Before disconnecting the connectors, make a note of where they are connected.

·

Reconnect each connector to its original position.



Result:
Result Proceed to
OK A
NG (No. 1 CAN junction connector main line) B
NG (CAN junction terminal main line) C



A

REPLACE NO. 2 CAN JUNCTION CONNECTOR

B

REPAIR OR REPLACE CAN MAIN BUS LINE OR CONNECTOR (NO. 1 CAN JUNCTION CONNECTOR - NO. 2 CAN JUNCTION CONNECTOR)

C

REPAIR OR REPLACE CAN MAIN BUS LINE OR CONNECTOR (NO. 2 CAN JUNCTION CONNECTOR - CAN JUNCTION TERMINAL)

28.CHECK FOR SHORT IN SUB BUS 2 LINES (NO. 1 CAN JUNCTION CONNECTOR - NETWORK GATEWAY ECU)
a.
C299845
1.042,1.677 1.458,1.938 0.417,0.26 1.125,2.573 1.24,3.073 1.24,3.073 1.313,3.073 true 0.708,2.781 0.771,2.781 0.771,2.781 1.021,2.51 true 1.271,2.521 1.656,2.729 1.656,2.729 1.74,2.729 true 1.25,2.396 1.656,2.115 1.656,2.115 1.708,2.115 true 0.073,0.052 0.385,0.25 0.313,0.198 10 false *a 1.094,1.719 1.708,1.917 0.615,0.198 10 false F105 0.563,2.688 0.719,2.885 0.156,0.198 10 false L 1.396,2.979 1.552,3.177 0.156,0.198 10 false W 1.792,2.021 2.708,2.219 0.917,0.198 10 false CANH*b 1.823,2.635 2.74,2.833 0.917,0.198 10 false CANL*b
*a Rear view of wire harness connector
(to No. 1 CAN Junction Connector)
*b to Network Gateway ECU


Disconnect the F105 wire harness connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F105-1 (CANH) - F105-2 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω



NOTICE:
·

Before disconnecting the connectors, make a note of where they are connected.

·

Reconnect each connector to its original position.



Result:
Result
OK
NG



OK

29.CHECK FOR SHORT IN SUB BUS 2 LINES (BRANCH LINE)

NG

35.CHECK FOR SHORT IN SUB BUS 2 LINES (NETWORK GATEWAY ECU)
29.CHECK FOR SHORT IN SUB BUS 2 LINES (BRANCH LINE)
a.

Reconnect the F105 wire harness connector.


b.
C295452
1.052,0.385 1.49,0.677 0.438,0.292 1.406,0.927 1.26,0.927 1.26,0.927 1.26,1.396 true 1.26,1.552 1.26,2.427 1.26,2.427 1.396,2.427 true 0.094,0.083 0.406,0.281 0.313,0.198 10 false *a 1.5,0.833 2.417,1.031 0.917,0.198 10 false CANH*b 1.5,2.333 2.417,2.531 0.917,0.198 10 false CANL*b 1.115,0.427 1.729,0.625 0.615,0.198 10 false F105
*a Rear view of wire harness connector
(to No. 1 CAN Junction Connector)
*b to Network Gateway ECU


Connect the probes of an ohmmeter to terminals 1 (CANH) and 2(CANL) of the network gateway ECU main line harness connector.


c.

While observing the resistance value shown on the tester, disconnect the F108, F110, M39 and M40 connectors from the No. 1 CAN junction connector or No. 2 CAN junction connector one by one until the resistance becomes normal (between 54 and 69 Ω).

C295454
3.385,2.542 3.698,2.698 0.313,0.156 10 false (*A) 5.156,1.813 5.469,1.969 0.313,0.156 10 false (*B) 1.708,4.01 2.021,4.167 0.313,0.156 10 false (*C) 3.677,4.646 3.99,4.802 0.313,0.156 10 false (*D) 1.458,1.813 1.771,1.969 0.313,0.156 10 false *1 3.219,2.542 3.531,2.698 0.313,0.156 10 false *2 5,1.813 5.313,1.958 0.313,0.146 10 false *3 1.552,4.01 1.865,4.167 0.313,0.156 10 false *4 3.521,4.646 3.833,4.802 0.313,0.156 10 false *5 5.677,3.99 5.99,4.146 0.313,0.156 10 false *6 3.198,0.448 3.51,0.604 0.313,0.156 10 false *7 3.417,6.104 3.729,6.26 0.313,0.156 10 false *8 6.156,1.969 6.469,2.167 0.313,0.198 10 false BR 6.802,1.969 6.958,2.167 0.156,0.198 10 false W 0.125,4.5 0.438,4.698 0.313,0.198 10 false BR 0.75,4.5 0.906,4.698 0.156,0.198 10 false W 1.208,1.219 1.365,1.417 0.156,0.198 10 false L 1.729,1.229 1.885,1.427 0.156,0.198 10 false W 3.01,1.594 3.167,1.792 0.156,0.198 10 false G 5.365,1.229 5.521,1.427 0.156,0.198 10 false W 3.563,1.594 3.719,1.792 0.156,0.198 10 false W 4.865,1.229 5.021,1.427 0.156,0.198 10 false R 1.427,4.552 1.583,4.75 0.156,0.198 10 false L 1.917,4.552 2.073,4.75 0.156,0.198 10 false Y 1.406,5.365 1.563,5.563 0.156,0.198 10 false B 1.927,5.365 2.083,5.563 0.156,0.198 10 false W 3.292,5.323 3.604,5.521 0.313,0.198 10 false GR 3.906,5.323 4.063,5.521 0.156,0.198 10 false W 5.969,4.969 6.125,5.167 0.156,0.198 10 false W 5.448,4.969 5.604,5.167 0.156,0.198 10 false B
*A w/ Pre-crash Safety System *B w/ Lane Departure Alert System
*C w/ Parking Assist Monitor System *D w/ Blind Spot Monitor System
*1 Network Gateway ECU *2 Driving Support ECU Assembly
*3 Lane Departure Warning Camera *4 Television Camera Assembly
*5 Blind Spot Monitor Sensor LH *6 CAN Junction Terminal
*7 No. 1 CAN Junction Connector *8 No. 2 CAN Junction Connector


C295455
2.344,0.458 2.656,0.656 0.313,0.198 10 false *a 3.552,3.406 4.167,3.604 0.615,0.198 10 false F104 3.552,3.667 4.167,3.865 0.615,0.198 10 false F105 3.542,3.958 4.156,4.156 0.615,0.198 10 false F108 3.542,4.24 4.156,4.438 0.615,0.198 10 false F110
*a Component without harness connected
(No. 1 CAN Junction Connector)
- -


Wiring Color:
No. 1 CAN Junction Connector Side Code Color (CANH Side) Color (CANL Side)
No. 2 CAN junction connector F104 BR W
Network gateway ECU F105 L W
Lane departure warning camera*1 F108 R W
Driving support ECU assembly*2 F110 G W


·

*1: w/ Lane Departure Alert System

·

*2: w/ Pre-crash Safety System


C299848
3.573,3.417 4.031,3.615 0.458,0.198 10 false M38 2.333,0.417 2.646,0.615 0.313,0.198 10 false *a 3.573,3.698 4.031,3.896 0.458,0.198 10 false M39 3.573,3.979 4.031,4.177 0.458,0.198 10 false M40 3.573,4.25 4.031,4.448 0.458,0.198 10 false M41
*a Component without harness connected
(No. 2 CAN Junction Connector)
- -


Wiring Color:
No. 1 CAN Junction Connector Side Code Color (CANH Side) Color (CANL Side)
No. 1 CAN junction connector M38 BR W
Television camera assembly*1 M39 B W
Blind spot monitor sensor LH*2 M40 GR W
CAN junction terminal M41 B W


·

*1: w/ Parking Assist Monitor System

·

*2: w/ Blind Spot Monitor System


NOTICE:

Do not reconnect the disconnected connectors until this inspection is complete because there may be a short in 2 or more branch lines.



Result:
Result Proceed to
The resistance is still below 54 Ω when all the specified connectors are disconnected. (There are no shorts between a pair of branch lines.) A
The resistance becomes normal (between 54 and 69 Ω) when a connector is disconnected. (There is a short between one or more pairs of branch lines.) B


d.

When there is a short in one or more of the branch lines:

i.

Reconnect all of the connectors to the CAN junction connector, except for the one that was disconnected last (the short-circuited bus line). Check that the resistance shown on the tester is normal (between 54 and 69 Ω) to confirm that there is a short in the one branch line only.

HINT:
·

Connectors that connect to the CAN junction connector can be distinguished by the color of their CAN bus lines.

·

Reconnecting the connectors to non-original positions on the CAN junction connector does not affect system performance. However, it is preferred to reconnect the connectors to their original positions to avoid negative effects on the wiring such as tension on the wiring harnesses, and to make future maintenance easier.






A

30.CHECK FOR SHORT IN SUB BUS 2 LINES (NO. 2 CAN JUNCTION CONNECTOR - CAN JUNCTION TERMINAL)

B

34.CHECK FOR SHORT IN SUB BUS 2 LINES (ECU, SENSOR)
30.CHECK FOR SHORT IN SUB BUS 2 LINES (NO. 2 CAN JUNCTION CONNECTOR - CAN JUNCTION TERMINAL)
a.
C299832
0.396,1.677 0.771,1.938 0.375,0.26 0.417,2.448 0.365,2.229 0.365,2.229 0.313,2.229 false 0.615,3.031 0.542,3.031 0.542,3.031 0.458,2.573 true 0.594,2.375 1,1.958 1,1.958 1.073,1.958 true 0.583,2.521 0.917,2.604 0.917,2.604 1.01,2.604 true 0.094,0.094 0.406,0.292 0.313,0.198 10 false *a 0.458,1.729 0.917,1.927 0.458,0.198 10 false M41 0.167,2.125 0.323,2.323 0.156,0.198 10 false B 0.688,2.938 0.844,3.135 0.156,0.198 10 false W 1.156,1.865 2.073,2.063 0.917,0.198 10 false CANH*b 1.104,2.51 2.021,2.708 0.917,0.198 10 false CANL*b
*a Rear view of wire harness connector
(to No. 2 CAN Junction Connector)
*b to CAN Junction Terminal


Disconnect the M41 wire harness connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M41-1 (CANH) - M41-2 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω



NOTICE:
·

Before disconnecting the connectors, make a note of where they are connected.

·

Reconnect each connector to its original position.



Result:
Result
OK
NG



OK

31.CHECK FOR SHORT IN SUB BUS 2 LINES (NO. 1 CAN JUNCTION CONNECTOR)

NG

33.CHECK FOR SHORT IN SUB BUS 2 LINES (CAN JUNCTION TERMINAL)
31.CHECK FOR SHORT IN SUB BUS 2 LINES (NO. 1 CAN JUNCTION CONNECTOR)
a.
C299846
1.365,1.656 1.771,1.906 0.406,0.25 1.563,2.354 2.01,1.865 2.01,1.865 2.104,1.865 true 1.427,2.552 1.521,3.01 1.521,3.01 1.583,3.01 true 1.573,2.51 1.969,2.771 1.969,2.771 2.104,2.771 true 1.333,2.458 1.25,2.229 1.25,2.229 1.177,2.229 true 0.073,0.063 0.385,0.26 0.313,0.198 10 false *a 1.406,1.688 2.021,1.885 0.615,0.198 10 false F104 2.208,1.771 3.125,1.969 0.917,0.198 10 false CANH*b 2.198,2.667 3.115,2.865 0.917,0.198 10 false CANL*b 1.656,2.917 1.813,3.115 0.156,0.198 10 false W 0.938,2.125 1.25,2.323 0.313,0.198 10 false BR
*a Rear view of wire harness connector
(to No. 1 CAN Junction Connector)
*b to No. 2 CAN Junction Connector


Disconnect the F104 wire harness connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F104-1 (CANH) - F104-2 (CANL) Cable disconnected from negative (-) battery terminal 1 MΩ or higher



NOTICE:
·

Before disconnecting the connectors, make a note of where they are connected.

·

Reconnect each connector to its original position.



Result:
Result
OK
NG



OK

REPLACE NO. 1 CAN JUNCTION CONNECTOR

NG

32.CHECK FOR SHORT IN SUB BUS 2 LINES (NO. 1 CAN JUNCTION CONNECTOR - NO. 2 CAN JUNCTION CONNECTOR)
32.CHECK FOR SHORT IN SUB BUS 2 LINES (NO. 1 CAN JUNCTION CONNECTOR - NO. 2 CAN JUNCTION CONNECTOR)
a.
C299834
1.365,1.667 1.75,1.938 0.385,0.271 1.563,2.375 1.885,2.01 1.885,2.01 1.958,2.01 true 1.573,2.521 1.896,2.417 1.896,2.417 2,2.417 true 1.417,2.573 1.594,3.073 1.594,3.073 1.667,3.073 true 1.094,2.323 1.188,2.323 1.188,2.323 1.323,2.49 true 0.094,0.094 0.406,0.292 0.313,0.198 10 false *a 1.427,1.708 1.885,1.906 0.458,0.198 10 false M38 2.031,1.917 2.948,2.115 0.917,0.198 10 false CANH*b 2.083,2.323 3,2.521 0.917,0.198 10 false CANL*b 0.844,2.229 1.156,2.427 0.313,0.198 10 false BR 1.74,2.979 1.896,3.177 0.156,0.198 10 false W
*a Rear view of wire harness connector
(to No. 2 CAN Junction Connector)
*b to No. 1 CAN Junction Connector


Disconnect the M38 wire harness connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M38-1 (CANH) - M38-2 (CANL) Cable disconnected from negative (-) battery terminal 1 MΩ or higher



NOTICE:
·

Before disconnecting the connectors, make a note of where they are connected.

·

Reconnect each connector to its original position.



Result:
Result
OK
NG



OK

REPLACE NO. 2 CAN JUNCTION CONNECTOR

NG

REPAIR OR REPLACE CAN MAIN BUS LINE OR CONNECTOR (NO. 1 CAN JUNCTION CONNECTOR - NO. 2 CAN JUNCTION CONNECTOR)

33.CHECK FOR SHORT IN SUB BUS 2 LINES (CAN JUNCTION TERMINAL)
a.

Reconnect the M41 wire harness connector.


b.
C292413C01
1.479,0.292 1.875,0.615 0.396,0.323 1.25,1.865 1.396,1.865 1.396,1.865 1.771,1.198 true 2.438,1.844 2.313,1.844 2.313,1.844 2.042,1.198 true 0.063,0.063 0.375,0.26 0.313,0.198 10 false *a 1.542,0.354 2.156,0.552 0.615,0.198 10 false M42 0.844,1.771 1.458,1.969 0.615,0.198 10 false CANL 2.5,1.75 3.115,1.948 0.615,0.198 10 false CANH
*a Front view of wire harness connector
(to CAN Junction Terminal)


Disconnect the M42 CAN junction terminal connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M42-3 (CANH) - M42-2 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω



Result:
Result
OK
NG



OK

REPLACE CAN JUNCTION TERMINAL

NG

REPAIR OR REPLACE CAN MAIN BUS LINE OR CONNECTOR (NO. 2 CAN JUNCTION CONNECTOR - CAN JUNCTION TERMINAL)

34.CHECK FOR SHORT IN SUB BUS 2 LINES (ECU, SENSOR)
a.

Reconnect all wire harness connectors (No. 1 CAN junction connector and No. 2 CAN junction connector).


b.
C242747
1.469,0.396 1.875,0.625 0.406,0.229 1.542,1.083 1.188,1.531 1.188,1.531 1.073,1.531 true 1.625,1.083 1.375,1.792 1.375,1.792 1.26,1.792 true 0.083,0.063 0.396,0.219 0.313,0.156 10 false *a 1.552,0.417 2.063,0.688 0.51,0.271 10 false F85 0.688,1.438 1.146,1.625 0.458,0.188 10 false CA2H 0.896,1.708 1.344,1.885 0.448,0.177 10 false CA2L
*a Component with harness connected
(Network Gateway ECU)


Disconnect the connector that includes terminals CANH and CANL from the ECU or sensor to which the short-circuited branch line is connected.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>TERMINALS OF ECU


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F85-13 (CA2H) - F85-12 (CA2L) Cable disconnected from negative (-) battery terminal 54 to 69 Ω


HINT:
·

If the resistance becomes normal (between 54 and 69 Ω) when the connector is disconnected from the ECU or sensor, there may be a short in the ECU or sensor.

·

If the resistance does not become normal (between 54 and 69 Ω) when the connector is disconnected from the ECU or sensor, repair or replace the short-circuited branch line or connector.




Result:
Result
OK
NG



OK

REPLACE CORRESPONDING ECU OR SENSOR

NG

REPAIR OR REPLACE CORRESPONDING ECU OR SENSOR BUS LINES OR CONNECTOR

35.CHECK FOR SHORT IN SUB BUS 2 LINES (NETWORK GATEWAY ECU)
a.

Reconnect the F105 wire harness connector.


b.
C292378
0.823,0.281 1.24,0.573 0.417,0.292 1.292,1.958 1.406,1.958 1.406,1.958 1.833,1.469 true 2.458,1.927 2.354,1.927 2.354,1.927 1.948,1.458 true 0.083,0.073 0.396,0.271 0.313,0.198 10 false *a 0.906,0.333 1.365,0.531 0.458,0.198 10 false F85 0.906,1.875 1.521,2.073 0.615,0.198 10 false CA2L 2.531,1.833 3.146,2.031 0.615,0.198 10 false CA2H
*a Front view of wire harness connector
(to Network Gateway ECU)


Disconnect the F85 network gateway ECU connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F85-13 (CA2H) - F85-12 (CA2L) Cable disconnected from negative (-) battery terminal 108 to 132 Ω



Result:
Result
OK
NG



OK

NG

REPAIR OR REPLACE CAN MAIN BUS LINE OR CONNECTOR (NETWORK GATEWAY ECU - NO. 1 CAN JUNCTION CONNECTOR)

36.CHECK FOR SHORT IN SUB BUS 2 LINE (NO. 2 CAN JUNCTION CONNECTOR - CAN JUNCTION TERMINAL)
a.
C299835
0.365,1.396 0.75,1.646 0.385,0.25 0.292,3.625 0.688,3.875 0.396,0.25 1.635,3.469 2.021,3.021 2.021,3.021 2.125,3.021 true 2.365,3.917 1.99,4.385 1.99,4.385 1.896,4.385 true 0.375,2.063 0.24,1.656 0.24,1.656 0.177,1.656 true 0.646,2.667 0.583,2.667 0.583,2.667 0.417,2.188 true 0.563,2 0.885,1.698 0.885,1.698 0.99,1.698 true 0.563,2.146 0.875,2.26 0.875,2.26 0.948,2.26 true 0.052,0.042 0.365,0.24 0.313,0.198 10 false *a 0.417,1.427 0.875,1.625 0.458,0.198 10 false M41 0.375,3.656 0.833,3.854 0.458,0.198 10 false F25 0.49,3.135 0.802,3.333 0.313,0.198 10 false *1 2.219,2.927 2.531,3.125 0.313,0.198 10 false CG 1.573,4.281 2.031,4.479 0.458,0.198 10 false BAT 0.031,1.563 0.188,1.76 0.156,0.198 10 false B 0.708,2.583 0.865,2.781 0.156,0.198 10 false W 1.073,1.604 1.99,1.802 0.917,0.198 10 false CANH*b 1.031,2.167 1.948,2.365 0.917,0.198 10 false CANL*b
*1 DLC3
*a Rear view of wire harness connector
(to No. 2 CAN Junction Connector)
*b to CAN Junction Terminal


Disconnect the M41 wire harness connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Result
M41-1 (CANH) - F25-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher Below 200 Ω: CANH ground short
M41-2 (CANL) - F25-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher Below 200 Ω: CANL ground short
M41-1 (CANH) - F25-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher Below 6 kΩ: CANH +B short
M41-2 (CANL) - F25-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher Below 6 kΩ: CANL +B short



NOTICE:
·

Before disconnecting the connectors, make a note of where they are connected.

·

Reconnect each connector to its original position.



HINT:
·

It is only necessary to perform the inspection in the above table for the result (short circuit) that was obtained in the Check Sub Bus 2 inspection.

·

Find the necessary inspection from the Purpose column that matches the result in the Result column from the Check Sub Bus 2 inspection.



Result:
Result
OK
NG



OK

37.CHECK FOR SHORT IN SUB BUS 2 LINE

NG

41.CHECK FOR SHORT IN SUB BUS 2 LINE (CAN JUNCTION TERMINAL)
37.CHECK FOR SHORT IN SUB BUS 2 LINE
a.

Reconnect the M41 wire harness connector.


b.
C295426
0.25,3.615 0.635,3.927 0.385,0.313 0.375,0.375 0.75,0.635 0.375,0.26 1.646,3.469 1.896,3.052 1.896,3.052 2.063,3.052 true 2.354,3.948 2.125,4.354 2.125,4.354 1.979,4.354 true 0.563,1.365 1,0.833 1,0.833 1.156,0.833 true 0.563,1.521 1.063,2.375 1.063,2.375 1.135,2.375 true 0.229,0.948 0.281,0.948 0.281,0.948 0.344,1.479 true 0.427,1.563 0.542,2.396 0.542,2.396 0.615,2.396 true 0.083,0.188 0.396,0.385 0.313,0.198 10 false *a 0.5,2.99 0.813,3.188 0.313,0.198 10 false *1 0.313,3.667 0.625,3.865 0.313,0.198 10 false F25 2.135,2.958 2.448,3.156 0.313,0.198 10 false CG 1.667,4.26 2.125,4.458 0.458,0.198 10 false BAT 0.438,0.417 1.052,0.615 0.615,0.198 10 false M41 1.24,0.74 1.854,0.938 0.615,0.198 10 false CANH 1.208,2.281 1.823,2.479 0.615,0.198 10 false CANL 0.698,2.302 0.854,2.5 0.156,0.198 10 false W 0.083,0.844 0.24,1.042 0.156,0.198 10 false B
*1 DLC3
*a Rear view of wire harness connector
(to No. 2 CAN Junction Connector)


Connect the probes of an ohmmeter to terminals 1 (CANH) and 2 (CANL) of the J603 wire harness connector and CG or BAT of the DLC3.

HINT:

It is only necessary to perform the inspection for the result (short circuit) that was obtained in the Check Sub Bus 2 inspection.



c.

While observing the resistance value shown on the ohmmeter, disconnect the F105, F108, F110, M39 and M40 connectors from the No. 1 CAN junction connector and No. 2 CAN junction connector until the resistance becomes normal (6 kΩ or higher (for +B short) or 200 Ω or higher (for ground short)).

C295454
3.385,2.542 3.698,2.698 0.313,0.156 10 false (*A) 5.156,1.813 5.469,1.969 0.313,0.156 10 false (*B) 1.708,4.01 2.021,4.167 0.313,0.156 10 false (*C) 3.677,4.646 3.99,4.802 0.313,0.156 10 false (*D) 1.458,1.813 1.771,1.969 0.313,0.156 10 false *1 3.219,2.542 3.531,2.698 0.313,0.156 10 false *2 5,1.813 5.313,1.958 0.313,0.146 10 false *3 1.552,4.01 1.865,4.167 0.313,0.156 10 false *4 3.521,4.646 3.833,4.802 0.313,0.156 10 false *5 5.677,3.99 5.99,4.146 0.313,0.156 10 false *6 3.198,0.448 3.51,0.604 0.313,0.156 10 false *7 3.417,6.104 3.729,6.26 0.313,0.156 10 false *8 6.156,1.969 6.469,2.167 0.313,0.198 10 false BR 6.802,1.969 6.958,2.167 0.156,0.198 10 false W 0.125,4.5 0.438,4.698 0.313,0.198 10 false BR 0.75,4.5 0.906,4.698 0.156,0.198 10 false W 1.208,1.219 1.365,1.417 0.156,0.198 10 false L 1.729,1.229 1.885,1.427 0.156,0.198 10 false W 3.01,1.594 3.167,1.792 0.156,0.198 10 false G 5.365,1.229 5.521,1.427 0.156,0.198 10 false W 3.563,1.594 3.719,1.792 0.156,0.198 10 false W 4.865,1.229 5.021,1.427 0.156,0.198 10 false R 1.427,4.552 1.583,4.75 0.156,0.198 10 false L 1.917,4.552 2.073,4.75 0.156,0.198 10 false Y 1.406,5.365 1.563,5.563 0.156,0.198 10 false B 1.927,5.365 2.083,5.563 0.156,0.198 10 false W 3.292,5.323 3.604,5.521 0.313,0.198 10 false GR 3.906,5.323 4.063,5.521 0.156,0.198 10 false W 5.969,4.969 6.125,5.167 0.156,0.198 10 false W 5.448,4.969 5.604,5.167 0.156,0.198 10 false B
*A w/ Pre-crash Safety System *B w/ Lane Departure Alert System
*C w/ Parking Assist Monitor System *D w/ Blind Spot Monitor System
*1 Network Gateway ECU *2 Driving Support ECU Assembly
*3 Lane Departure Warning Camera *4 Lane Departure Warning Camera
*5 Blind Spot Monitor Sensor LH *6 CAN Junction Terminal
*7 No. 1 CAN Junction Connector *8 No. 2 CAN Junction Connector


C295455
2.344,0.458 2.656,0.656 0.313,0.198 10 false *a 3.552,3.406 4.167,3.604 0.615,0.198 10 false F104 3.552,3.667 4.167,3.865 0.615,0.198 10 false F105 3.542,3.958 4.156,4.156 0.615,0.198 10 false F108 3.542,4.24 4.156,4.438 0.615,0.198 10 false F110
*a Component without harness connected
(No. 1 CAN Junction Connector)
- -


Wiring Color:
No. 1 CAN Junction Connector Side Code Color (CANH Side) Color (CANL Side)
No. 2 CAN junction connector F104 BR W
Network gateway ECU F105 L W
Lane departure warning camera*1 F108 R W
Driving support ECU assembly*2 F110 G W


·

*1: w/ Lane Departure Alert System

·

*2: w/ Pre-crash Safety System


C299848
3.573,3.417 4.031,3.615 0.458,0.198 10 false M38 2.333,0.417 2.646,0.615 0.313,0.198 10 false *a 3.573,3.698 4.031,3.896 0.458,0.198 10 false M39 3.573,3.979 4.031,4.177 0.458,0.198 10 false M40 3.573,4.25 4.031,4.448 0.458,0.198 10 false M41
*a Component without harness connected
(No. 2 CAN Junction Connector)
- -


Wiring Color:
No. 1 CAN Junction Connector Side Code Color (CANH Side) Color (CANL Side)
No. 1 CAN junction connector M38 BR W
Television camera assembly*1 M39 B W
Blind spot monitor sensor LH*2 M40 GR W
CAN junction terminal M41 B W


·

*1: w/ Parking Assist Monitor System

·

*2: w/ Blind Spot Monitor System



Result:
Result Proceed to
The resistance between terminals CANH and BAT, or the resistance between terminals CANL and BAT is still below 6 kΩ when all the specified connectors are disconnected from the CAN junction connector.
(There is a short to +B in the CAN main bus lines between the No. 1 CAN junction connector and No. 2 CAN junction connector.)
A
The resistance between terminals CANH and GND, or the resistance between terminals CANL and GND is still below 200 Ω when all the specified connectors are disconnected from the CAN junction connector.
(There is a short to GND in the CAN main bus lines between the No. 1 CAN junction connector and No. 2 CAN junction connector.)
The resistance between terminals CANH and BAT, or the resistance between terminals CANL and BAT becomes normal (6 kΩ or higher) when a connector is disconnected from the CAN junction connector.
(There is a short to +B in one of the areas that relate to one or more of the disconnected bus lines.)
B
The resistance between terminals CANH and GND, or the resistance between terminals CANL and GND becomes normal (200 Ω or higher) when a connector is disconnected from the CAN junction connector.
(There is a short to GND in one of the areas that relate to the disconnected bus lines.)



A

38.CHECK FOR SHORT IN SUB BUS 2 LINE (NO. 2 CAN JUNCTION CONNECTOR)

B

40.CHECK FOR SHORT IN SUB BUS 2 LINE (ECU, SENSOR)
38.CHECK FOR SHORT IN SUB BUS 2 LINE (NO. 2 CAN JUNCTION CONNECTOR)
a.

Reconnect all wire harness connectors (No. 1 CAN junction connector and No. 2 CAN junction connector).


b.

Disconnect the M38 wire harness connector.


c.
C299836
0.365,0.26 0.76,0.542 0.396,0.281 0.292,3.604 0.667,3.854 0.375,0.25 0.563,1.135 1.073,0.281 1.073,0.281 1.167,0.281 true 0.552,1.292 1.198,0.625 1.198,0.625 1.271,0.625 true 0.688,2.167 0.615,2.167 0.615,2.167 0.427,1.333 true 0.229,0.667 0.281,0.667 0.281,0.667 0.344,1.24 true 1.646,3.438 1.99,3.052 1.99,3.052 2.094,3.052 true 2.354,3.938 1.969,4.396 1.969,4.396 1.885,4.396 true 0.073,0.073 0.385,0.271 0.313,0.198 10 false *a 0.438,0.313 0.896,0.51 0.458,0.198 10 false M41 1.24,0.188 2.156,0.385 0.917,0.198 10 false CANH*b 1.344,0.531 2.26,0.729 0.917,0.198 10 false CANL*b 0.781,2.063 0.938,2.26 0.156,0.198 10 false W 0.094,0.563 0.25,0.76 0.156,0.198 10 false B 0.448,2.948 0.76,3.146 0.313,0.198 10 false *1 0.365,3.635 0.823,3.833 0.458,0.198 10 false F25 2.188,2.958 2.5,3.156 0.313,0.198 10 false CG 1.573,4.292 2.031,4.49 0.458,0.198 10 false BAT
*1 DLC3
*a Rear view of wire harness connector
(to No. 2 CAN Junction Connector)
*b to CAN Junction Terminal


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Result
M41-1 (CANH) - F25-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher Below 200 Ω: CANH ground short
M41-2 (CANL) - F25-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher Below 200 Ω: CANL ground short
M41-1 (CANH) - F25-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher Below 6 kΩ: CANH +B short
M41-2 (CANL) - F25-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher Below 6 kΩ: CANL +B short



NOTICE:
·

Before disconnecting the connectors, make a note of where they are connected.

·

Reconnect each connector to its original position.



HINT:
·

It is only necessary to perform the inspection in the above table for the result (short circuit) that was obtained in the Check Sub Bus 2 inspection.

·

Find the necessary inspection from the Purpose column that matches the result in the Result column from the Check Sub Bus 2 inspection.



Result:
Result
OK
NG



OK

39.CHECK FOR SHORT IN SUB BUS 2 LINE (NO. 1 CAN JUNCTION CONNECTOR)

NG

REPLACE NO. 2 CAN JUNCTION CONNECTOR

39.CHECK FOR SHORT IN SUB BUS 2 LINE (NO. 1 CAN JUNCTION CONNECTOR)
a.

Reconnect the M38 wire harness connector.


b.

Disconnect the F104 wire harness connector.


c.
C295426
0.25,3.615 0.625,3.948 0.375,0.333 0.375,0.385 0.76,0.625 0.385,0.24 1.646,3.469 1.896,3.052 1.896,3.052 2.063,3.052 true 2.354,3.948 2.125,4.354 2.125,4.354 1.979,4.354 true 0.563,1.354 1,0.823 1,0.823 1.156,0.823 true 0.563,1.531 0.979,2.323 0.979,2.323 1.063,2.323 true 0.198,0.781 0.25,0.781 0.25,0.781 0.365,1.448 true 0.427,1.563 0.542,2.396 0.542,2.396 0.615,2.396 true 0.094,0.219 0.406,0.417 0.313,0.198 10 false *a 0.5,2.99 0.813,3.188 0.313,0.198 10 false *1 0.323,3.667 0.635,3.865 0.313,0.198 10 false F25 2.135,2.958 2.448,3.156 0.313,0.198 10 false CG 1.667,4.26 2.125,4.458 0.458,0.198 10 false BAT 0.438,0.406 1.052,0.604 0.615,0.198 10 false M41 1.24,0.729 1.854,0.927 0.615,0.198 10 false CANH*b 1.135,2.229 1.75,2.427 0.615,0.198 10 false CANL*b 0.688,2.302 0.844,2.5 0.156,0.198 10 false W 0.052,0.677 0.208,0.875 0.156,0.198 10 false B
*1 DLC3
*a Rear view of wire harness connector
(to No. 2 CAN Junction Connector)
*b to CAN Junction Terminal


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Result
M41-1 (CANH) - F25-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher Below 200 Ω: CANH ground short
M41-2 (CANL) - F25-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher Below 200 Ω: CANL ground short
M41-1 (CANH) - F25-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher Below 6 kΩ: CANH +B short
M41-2 (CANL) - F25-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher Below 6 kΩ: CANL +B short



NOTICE:
·

Before disconnecting the connectors, make a note of where they are connected.

·

Reconnect each connector to its original position.



HINT:
·

It is only necessary to perform the inspection in the above table for the result (short circuit) that was obtained in the Check Sub Bus 2 inspection.

·

Find the necessary inspection from the Purpose column that matches the result in the Result column from the Check Sub Bus 2 inspection.



Result:
Result
OK
NG



OK

REPLACE NO. 1 CAN JUNCTION CONNECTOR

NG

REPAIR OR REPLACE CAN MAIN BUS LINE OR CONNECTOR (NO. 1 CAN JUNCTION CONNECTOR - NO. 2 CAN JUNCTION CONNECTOR)

40.CHECK FOR SHORT IN SUB BUS 2 LINE (ECU, SENSOR)
a.

Reconnect all wire harness connectors (No. 1 CAN junction connector and No. 2 CAN junction connector).


b.

Disconnect the connector that includes terminals CANH and CANL from the ECU or sensor to which the bus line shorted to +B or shorted to GND is connected.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>TERMINALS OF ECU


c.
C295426
0.25,3.615 0.635,3.927 0.385,0.313 0.375,0.375 0.75,0.635 0.375,0.26 1.646,3.469 1.896,3.052 1.896,3.052 2.063,3.052 true 2.354,3.948 2.125,4.354 2.125,4.354 1.979,4.354 true 0.563,1.365 1,0.833 1,0.833 1.156,0.833 true 0.563,1.521 1.063,2.375 1.063,2.375 1.135,2.375 true 0.229,0.948 0.281,0.948 0.281,0.948 0.344,1.479 true 0.427,1.563 0.542,2.396 0.542,2.396 0.615,2.396 true 0.083,0.188 0.396,0.385 0.313,0.198 10 false *a 0.5,2.99 0.813,3.188 0.313,0.198 10 false *1 0.313,3.667 0.625,3.865 0.313,0.198 10 false F25 2.135,2.958 2.448,3.156 0.313,0.198 10 false CG 1.667,4.26 2.125,4.458 0.458,0.198 10 false BAT 0.438,0.417 1.052,0.615 0.615,0.198 10 false M41 1.24,0.74 1.854,0.938 0.615,0.198 10 false CANH 1.208,2.281 1.823,2.479 0.615,0.198 10 false CANL 0.698,2.302 0.854,2.5 0.156,0.198 10 false W 0.083,0.844 0.24,1.042 0.156,0.198 10 false B
*1 DLC3
*a Rear view of wire harness connector
(to No. 2 CAN Junction Connector)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Result
M41-1 (CANH) - F25-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher Below 200 Ω: CANH ground short
M41-2 (CANL) - F25-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher Below 200 Ω: CANL ground short
M41-1 (CANH) - F25-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher Below 6 kΩ: CANH +B short
M41-2 (CANL) - F25-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher Below 6 kΩ: CANH +B short


HINT:
·

It is only necessary to perform the inspection in the above table for the result (short circuit) that was obtained in the Check Sub Bus 2 inspection.

·

If the resistance becomes normal when the connector is disconnected from the ECU, there may be a short in the ECU.

·

Find the necessary inspection from the Purpose column that matches the result in the Result column from the Check Sub Bus 2 inspection.




Result:
Result
OK
NG



OK

REPLACE CORRESPONDING ECU OR SENSOR

NG

REPAIR OR REPLACE CORRESPONDING ECU OR SENSOR BUS LINES OR CONNECTOR

41.CHECK FOR SHORT IN SUB BUS 2 LINE (CAN JUNCTION TERMINAL)
a.

Reconnect the M41 wire harness connector.


b.

Disconnect the M42 CAN junction terminal connector.


c.
C287171
1.5,0.26 1.938,0.573 0.438,0.313 1.521,2.635 1.958,2.927 0.438,0.292 1.625,3.542 2.104,3.094 2.104,3.094 2.281,3.094 true 1.771,4.479 1.917,4.479 1.917,4.479 2.323,4.094 true 1.115,2.26 1.26,2.26 1.26,2.26 1.781,1.563 true 2.552,2.24 2.385,2.24 2.385,2.24 2.021,1.573 true 0.115,0.094 0.427,0.292 0.313,0.198 10 false *a 0.156,2.51 0.469,2.708 0.313,0.198 10 false *1 1.594,0.313 2.208,0.51 0.615,0.198 10 false M42 1.625,2.677 1.938,2.875 0.313,0.198 10 false F25 2.344,3.01 2.656,3.208 0.313,0.198 10 false CG 1.469,4.396 1.927,4.594 0.458,0.198 10 false BAT 0.719,2.177 1.333,2.375 0.615,0.198 10 false CANL 2.604,2.146 3.219,2.344 0.615,0.198 10 false CANH
*1 DLC3
*a Front view of wire harness connector
(to CAN Junction Terminal)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Result
M42-3 (CANH) - F25-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher Below 200 Ω: CANH ground short
M42-2 (CANL) - F25-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher Below 200 Ω: CANL ground short
M42-3 (CANH) - F25-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher Below 6 kΩ: CANH +B short
M42-2 (CANL) - F25-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher Below 6 kΩ: CANL +B short



HINT:
·

It is only necessary to perform the inspection in the above table for the result (short circuit) that was obtained in the Check Sub Bus 2 inspection.

·

Find the necessary inspection from the Purpose column that matches the result in the Result column from the Check Sub Bus 2 inspection.



Result:
Result
OK
NG



OK

REPLACE CAN JUNCTION TERMINAL

NG

REPAIR OR REPLACE CAN MAIN BUS LINE OR CONNECTOR (NO. 2 CAN JUNCTION CONNECTOR - CAN JUNCTION TERMINAL)