Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM › 2013.12–2016.11
RM3160E _57 Power Source / Network _019704 NETWORKING _0095663 CAN COMMUNICATION SYSTEM C

NETWORKING  CAN COMMUNICATION SYSTEM  U0233  Lost Communication with Blind Spot Monitor Master Module  


DESCRIPTION

DTC No. Detection Item DTC Detection Condition Trouble Area Note
U0233 Lost Communication with Blind Spot Monitor Master Module No communication from the blind spot monitor sensor LH continues.
·

Blind spot monitor sensor LH branch line or connector

·

Power source circuit of blind spot monitor sensor LH

·

Blind spot monitor sensor LH ground circuit

·

Blind spot monitor sensor LH


HINT:

Network gateway ECU stores DTCs when it detects a communication stop or network communication error for ECUs connected to sub bus 2.



HINT:

This diagnosis procedure is for when DTC U0233 is output by the network gateway ECU (GTS display: Gateway).


WIRING DIAGRAM

C294987
1.75,1.125 2.229,0.385 2.229,0.385 2.354,0.385 false 3.885,1.125 4.365,0.385 4.365,0.385 4.49,0.385 false 0.042,0.042 1.875,0.281 1.833,0.24 12 false Sub Bus 2: 0.708,2.01 1.479,2.208 0.771,0.198 10 false 120 Ω 6.135,2.01 6.906,2.208 0.771,0.198 10 false 120 Ω 3.125,4.344 5.042,4.594 1.917,0.25 10 false Blind Spot Monitor Sensor LH 2.781,4.344 3.24,4.542 0.458,0.198 10 false M31 2.104,3.969 2.813,4.188 0.708,0.219 10 false DSS-IG 3.25,3.813 3.708,4.01 0.458,0.198 10 false BLB 3.5,3.49 4.115,3.688 0.615,0.198 10 false CA1P 3.99,3.49 4.604,3.688 0.615,0.198 10 false CA1N 0.302,2.656 1.427,3.292 1.125,0.635 10 false Network Gateway ECU 5.646,2.677 7.104,2.99 1.458,0.313 10 false CAN Junction Terminal 4.24,3.771 4.854,3.969 0.615,0.198 10 false BLGD 4.656,3.677 4.969,3.875 0.313,0.198 10 false 10 4.177,3.281 4.333,3.479 0.156,0.198 10 false 7 3.604,3.281 3.76,3.479 0.156,0.198 10 false 2 3.083,3.719 3.24,3.917 0.156,0.198 10 false 5 1.146,3.979 2.979,4.177 1.833,0.198 10 false Trouble Area 1.125,5.063 5.104,5.26 3.979,0.198 10 false : CAN Main Bus Line (CANH) 1.125,5.396 5.104,5.594 3.979,0.198 10 false : CAN Main Bus Line (CANL) 4.25,5.052 6.021,5.365 1.771,0.313 10 false : CAN Branch Line (CANH) 4.25,5.396 5.969,5.635 1.719,0.24 10 false : CAN Branch Line (CANL) 2.417,0.292 3.656,1.135 1.24,0.844 10 false No. 1 CAN Junction Connector 4.563,0.292 5.802,1.135 1.24,0.844 10 false No. 2 CAN Junction Connector

CAUTION / NOTICE / HINT

NOTICE:
·

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key, switches or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING

·

After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

·

DTC check procedure: Turn the ignition switch to ON and wait at least 11.84 seconds.

·

After the repair, perform the CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM

·

Inspect the fuses for circuits related to this system before performing the following procedure.



HINT:
·

Operating the ignition switch, any other switches or a door triggers related ECU and sensor communication on the CAN. This communication will cause the resistance value to change.

·

Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.



PROCEDURE

1.RECONFIRM DTC OUTPUT
Body Electrical > Gateway > Trouble Codes
50001 150
a.

Reconfirm DTCs.

HINT:

If DTC U1002 is output from Gateway of the network gateway ECU, this indicates a sub bus 2 malfunction. Troubleshoot for DTC U1002 and check for malfunctions in sub bus 2.



Result:
Result Proceed to
DTC U1002 is not output from network gateway ECU (GTS display: Gateway) A
DTC U1002 is output from network gateway ECU (GTS display: Gateway) B



A

2.CHECK FOR OPEN IN SUB BUS 2 LINES (BLIND SPOT MONITOR SENSOR LH BRANCH LINE)

B

GO TO DIAGNOSIS PROCEDURE INDICATED BY OUTPUT DTC

2.CHECK FOR OPEN IN SUB BUS 2 LINES (BLIND SPOT MONITOR SENSOR LH BRANCH LINE)
a.

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the M31 blind spot monitor sensor LH connector.


c.
C285248
1.458,0.146 1.875,0.406 0.417,0.26 1.552,1.01 1.219,0.344 1.219,0.344 1.01,0.344 true 1.563,1.198 1.26,1.802 1.26,1.802 1.052,1.802 true 0.104,0.073 0.417,0.229 0.313,0.156 10 false *a 0.656,1.708 1.271,1.906 0.615,0.198 10 false CA1N 0.615,0.26 1.229,0.458 0.615,0.198 10 false CA1P 1.542,0.188 1.854,0.385 0.313,0.198 10 false M31
*a Front view of wire harness connector
(to Blind Spot Monitor Sensor LH)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M31-2 (CA1P) - M31-7 (CA1N) Cable disconnected from negative (-) battery terminal 54 to 69 Ω



Result:
Result
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)

NG

REPAIR OR REPLACE CAN BRANCH LINE OR CONNECTOR (BLIND SPOT MONITOR SENSOR LH)

3.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)
a.
C285248
1.479,0.167 1.896,0.427 0.417,0.26 1.927,1.208 2.146,1.813 2.146,1.813 2.313,1.813 true 0.125,0.073 0.438,0.229 0.313,0.156 10 false *a 2.375,1.719 2.99,1.917 0.615,0.198 10 false BLGD 1.563,0.208 1.875,0.406 0.313,0.198 10 false M31
*a Front view of wire harness connector
(to Blind Spot Monitor Sensor LH)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M31-10 (BLGD) - Body ground Cable disconnected from negative (-) battery terminal Below 1 Ω



b.

Reconnect the cable to the negative (-) battery terminal.


c.
C285248
1.479,0.167 1.896,0.427 0.417,0.26 1.938,0.99 2.188,0.385 2.188,0.385 2.365,0.385 true 0.125,0.073 0.438,0.229 0.313,0.156 10 false *a 2.406,0.302 3.021,0.5 0.615,0.198 10 false BLB 1.563,0.198 1.875,0.396 0.313,0.198 10 false M31
*a Front view of wire harness connector
(to Blind Spot Monitor Sensor LH)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
M31-5 (BLB) - Body ground Ignition switch ON 11 to 14 V



Result:
Result
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)