Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM
RM3160E _57 Power Source / Network _019704 NETWORKING _0095663 CAN COMMUNICATION SYSTEM C

NETWORKING  CAN COMMUNICATION SYSTEM  U0230  Lost Communication with Rear Gate Module  


DESCRIPTION

DTC No. Detection Item DTC Detection Condition Trouble Area Note
U0230 Lost Communication with Rear Gate Module No communication from the multiplex network door ECU continues.
·

Multiplex network door ECU main line or connector

·

Power source circuit of multiplex network door ECU

·

Multiplex network door ECU ground circuit

·

Multiplex network door ECU


HINT:

Main body ECU (multiplex network body ECU) stores DTCs when it detects a communication stop or network communication error for ECUs connected to sub bus 1.



HINT:

This diagnosis procedure is for when DTC U0230 is output by the main body ECU (multiplex network body ECU) (GTS display: Main Body).


WIRING DIAGRAM

C294981E01
3.688,3.052 4.646,0.635 4.646,0.635 4.771,0.635 false 4.75,3.052 5,2.313 5,2.313 5.094,2.313 false 0.052,0.021 1.885,0.26 1.833,0.24 12 false Sub Bus 1: 1.271,0.583 5.25,0.781 3.979,0.198 10 false : CAN Main Bus Line (CANH) 1.271,0.927 5.25,1.125 3.979,0.198 10 false : CAN Main Bus Line (CANL) 1.969,3.917 2.74,4.115 0.771,0.198 10 false 120 Ω 6.156,3.927 6.927,4.125 0.771,0.198 10 false 120 Ω 1.667,4.542 2.792,4.927 1.125,0.385 10 false Multiplex Network Door ECU 5.802,4.573 7,5.281 1.198,0.708 10 false Main Body ECU (Multiplex Network Body ECU) 4.865,0.542 6.833,1.052 1.969,0.51 10 false No. 5 CAN Junction Connector 5.188,2.219 7.156,2.729 1.969,0.51 10 false No. 6 CAN Junction Connector 1.385,3.635 1.844,3.833 0.458,0.198 10 false X6 1.385,3.104 1.844,3.302 0.458,0.198 10 false X7 1.396,4.271 1.854,4.469 0.458,0.198 10 false X7 1.698,3.104 1.854,3.302 0.156,0.198 10 false B 1.677,4.271 2.135,4.469 0.458,0.198 10 false GND 1.698,3.635 2.01,3.833 0.313,0.198 10 false IG 0.594,3.25 1.052,3.448 0.458,0.198 10 false PBD 0.51,3.802 1.396,4.021 0.885,0.219 10 false IG1 NO. 3 2.396,3.083 3.01,3.281 0.615,0.198 10 false CANP 2.396,3.958 3.01,4.156 0.615,0.198 10 false CANN 1.313,5.167 3.146,5.365 1.833,0.198 10 false Trouble Area 1.438,2.906 1.594,3.104 0.156,0.198 10 false 8 1.427,3.427 1.583,3.625 0.156,0.198 10 false 7 1.427,4.063 1.583,4.26 0.156,0.198 10 false 7 2.906,3 3.219,3.198 0.313,0.198 10 false 13 2.906,4.031 3.219,4.229 0.313,0.198 10 false 14 2.917,3.198 3.375,3.396 0.458,0.198 10 false X6 2.917,3.823 3.375,4.021 0.458,0.198 10 false X6

CAUTION / NOTICE / HINT

NOTICE:
·

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key, switches or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING

·

After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

·

DTC check procedure: Turn the ignition switch to ON and wait at least 20 seconds.

·

After the repair, perform the CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM

·

Inspect the fuses for circuits related to this system before performing the following procedure.



HINT:
·

Operating the ignition switch, any other switches or a door triggers related ECU and sensor communication on the CAN. This communication will cause the resistance value to change.

·

Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.



PROCEDURE

1.RECONFIRM DTC OUTPUT
Body Electrical > Main Body > Trouble Codes
50001 123
a.

Reconfirm DTCs.

HINT:

If DTC U1002 is output from Main Body of the main body ECU (multiplex network body ECU), this indicates a sub bus 1 malfunction. Troubleshoot for DTC U1002 and check for malfunctions in sub bus 1.



Result:
Result Proceed to
DTC U1002 is not output from main body ECU (multiplex network body ECU) (GTS display: Main Body) A
DTC U1002 is output from main body ECU (multiplex network body ECU) (GTS display: Main Body) B



A

2.CHECK FOR OPEN IN SUB BUS 1 LINES (MULTIPLEX NETWORK DOOR ECU MAIN LINE)

B

GO TO DIAGNOSIS PROCEDURE INDICATED BY OUTPUT DTC

2.CHECK FOR OPEN IN SUB BUS 1 LINES (MULTIPLEX NETWORK DOOR ECU MAIN LINE)
a.

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the X6 multiplex network door ECU connector.


c.
C292400C01
1.5,0.281 1.938,0.563 0.438,0.281 0.573,1.854 0.646,1.854 0.646,1.854 0.76,1.427 true 1.083,1.854 1.01,1.854 1.01,1.854 0.885,1.438 true 0.052,0.063 0.365,0.26 0.313,0.198 10 false *a 1.646,0.323 2.104,0.521 0.458,0.198 10 false X6 0.156,1.75 0.771,1.948 0.615,0.198 10 false CANP 1.146,1.75 1.76,1.948 0.615,0.198 10 false CANN
*a Front view of wire harness connector
(to Multiplex Network Door ECU)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
X6-13 (CANP) - X6-14 (CANN) Cable disconnected from negative (-) battery terminal 108 to 132 Ω



Result:
Result
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)

NG

REPAIR OR REPLACE CAN MAIN LINE OR CONNECTOR (MULTIPLEX NETWORK DOOR ECU)

3.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)
a.

Disconnect the X7 multiplex network door ECU connector.


b.
C294982C01
1.5,0.188 1.917,0.5 0.417,0.313 1.135,1.896 1.24,1.896 1.24,1.896 1.583,1.344 true 1.646,0.24 2.104,0.438 0.458,0.198 10 false X7 0.104,0.083 0.417,0.281 0.313,0.198 10 false *a 0.771,1.802 1.229,2 0.458,0.198 10 false GND
*a Front view of wire harness connector
(to Multiplex Network Door ECU)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
X7-7 (GND) - Body ground Cable disconnected from negative (-) battery terminal Below 1 Ω



c.

Reconnect the cable to the negative (-) battery terminal.


d.
C294985C01
1.479,0.271 1.896,0.563 0.417,0.292 1.51,2.479 1.927,2.771 0.417,0.292 2.406,1.99 2.292,1.99 2.292,1.99 1.792,1.531 true 2.417,2.823 2.313,2.823 2.313,2.823 1.781,3.458 true 0.063,0.083 0.375,0.281 0.313,0.198 10 false *a 1.646,2.521 2.104,2.719 0.458,0.198 10 false X6 1.625,0.313 2.083,0.51 0.458,0.198 10 false X7 2.479,1.896 2.635,2.094 0.156,0.198 10 false B 2.469,2.729 2.781,2.927 0.313,0.198 10 false IG
*a Front view of wire harness connector
(to Multiplex Network Door ECU)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
X7-8 (B) - Body ground Always 11 to 14 V
X6-7 (IG) - Body ground Ignition switch ON 11 to 14 V



Result:
Result
OK
NG



OK

REPLACE MULTIPLEX NETWORK DOOR ECU

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)