There may be a short circuit between one of the CAN bus lines and +B when no resistance exists between terminals 6 (CANH) and 16 (BAT) or 14 (CANL) and 16 (BAT) of the DLC3.
| Symptom | Trouble Area |
|---|---|
| No resistance exists between terminals 6 (CANH) and 16 (BAT) or 14 (CANL) and 16 (BAT) of DLC3. | ·
Short in CAN main bus line ·
Short in CAN branch line ·
Combination meter assembly ·
Power steering ECU assembly ·
Main body ECU (multiplex network body ECU) ·
Steering sensor ·
Airbag sensor assembly ·
ECM ·
Skid control ECU (brake actuator assembly) ·
Air conditioning amplifier assembly ·
Network gateway ECU*1 ·
4WD ECU assembly*2 ·
Navigation receiver assembly*3 ·
Radio and display receiver assembly*4 ·
Clearance warning ECU assembly*5 ·
Headlight leveling ECU assembly*6 ·
Certification ECU (smart key ECU assembly)*7 ·
No. 3 CAN junction connector ·
No. 4 CAN junction connector |
*1: w/ Blind Spot Monitor System or Parking Assist Monitor System
*2: for AWD
*3: for Navigation Receiver Type
*4: for Radio and Display Type
*5: w/ Toyota Parking Assist-sensor System
*6: w/ Automatic Headlight Beam Level Control System
*7: w/ Smart Entry and Start System
Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key, switches or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION
Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.
Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING
After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.
DTC check procedure: Turn the ignition switch to ON and wait at least 60 seconds, and then drive the vehicle at a speed of 60 km/h (37 mph) or more for 7 seconds or more.
After the repair, perform the CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed.
Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM
If the main body ECU (multiplex network body ECU) is replaced, refer to Registration.*
*: w/ Smart Entry and Start System
Operating the ignition switch, any other switches or a door triggers related ECU and sensor communication on the CAN. This communication will cause the resistance value to change.
Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.
Disconnect the cable from the negative (-) battery terminal.
Disconnect the F102 No. 3 CAN junction connector.
| *1 | DLC3 | - | - |
| *a | Front view of wire harness connector
(No. 3 CAN Junction Connector) |
*b | to No. 4 CAN Junction Connector |
| *c | to ECM | *d | to Air Conditioning Amplifier Assembly |
| *e | to Airbag Sensor Assembly | *f | to Clearance Warning ECU Assembly
(w/ Toyota Parking Assist-sensor System) |
| *g | to Main Body ECU (Multiplex Network Body ECU) | *h | to Certification ECU (Smart Key ECU Assembly)
(w/ Smart Entry and Start System) |
| *i | to 4WD ECU Assembly
(for AWD) |
*j | to Headlight Leveling ECU Assembly
(w/ Automatic Headlight Beam Level Control System) |
| *k | to Network Gateway ECU
(w/ Blind Spot Monitor System or Parking Assist Monitor System) |
- | - |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition | Connected to |
|---|---|---|---|
| F102-1 (CANH) - F25-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher | No. 4 CAN junction connector |
| F102-11 (CANL) - F25-16 (BAT) | |||
| F102-2 (CANH) - F25-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher | ECM |
| F102-12 (CANL) - F25-16 (BAT) | |||
| F102-3 (CANH) - F25-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher | Air conditioning amplifier assembly |
| F102-13 (CANL) - F25-16 (BAT) | |||
| F102-4 (CANH) - F25-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher | Airbag sensor assembly |
| F102-14 (CANL) - F25-16 (BAT) | |||
| F102-5 (CANH) - F25-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher | Clearance warning ECU assembly*1 |
| F102-15 (CANL) - F25-16 (BAT) | |||
| F102-6 (CANH) - F25-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher | Main body ECU (multiplex network body ECU) |
| F102-16 (CANL) - F25-16 (BAT) | |||
| F102-7 (CANH) - F25-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher | Certification ECU (smart key ECU assembly)*2 |
| F102-17 (CANL) - F25-16 (BAT) | |||
| F102-8 (CANH) - F25-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher | 4WD ECU assembly*3 |
| F102-18 (CANL) - F25-16 (BAT) | |||
| F102-9 (CANH) - F25-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher | Headlight leveling ECU assembly*4 |
| F102-19 (CANL) - F25-16 (BAT) | |||
| F102-10 (CANH) - F25-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher | Network gateway ECU*5 |
| F102-20 (CANL) - F25-16 (BAT) |
*1: w/ Toyota Parking Assist-sensor System
*2: w/ Smart Entry and Start System
*3: for AWD
*4: w/ Automatic Headlight Beam Level Control System
*5: w/ Blind Spot Monitor System or Parking Assist Monitor System
| Result | Proceed to |
|---|---|
| OK | A |
| NG (No. 4 CAN junction connector main line) | B |
| NG (ECU or sensor bus line) | C |
A
B
C
Reconnect the F102 No. 3 CAN junction connector.
Disconnect the F103 No. 4 CAN junction connector.
| *1 | DLC3 | - | - |
| *a | Front view of wire harness connector
(No. 4 CAN Junction Connector) |
*b | to No. 3 CAN Junction Connector |
| *c | to Skid Control ECU (Brake Actuator Assembly) | *d | to DLC3 |
| *e | to Steering Sensor | *f | to Power Steering ECU Assembly |
| *g | to Navigation Receiver Assembly
(for Navigation Receiver Type) |
*h | to Radio and Display Receiver Assembly
(for Radio and Display Type) |
| *i | to Combination Meter Assembly | - | - |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition | Connected to |
|---|---|---|---|
| F103-1 (CANH) - F25-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher | No. 3 CAN junction connector |
| F103-11 (CANL) - F25-16 (BAT) | |||
| F103-2 (CANH) - F25-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher | Skid control ECU (brake actuator assembly) |
| F103-12 (CANL) - F25-16 (BAT) | |||
| F103-3 (CANH) - F25-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher | DLC3 |
| F103-13 (CANL) - F25-16 (BAT) | |||
| F103-4 (CANH) - F25-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher | Steering sensor |
| F103-14 (CANL) - F25-16 (BAT) | |||
| F103-5 (CANH) - F25-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher | Power steering ECU assembly |
| F103-15 (CANL) - F25-16 (BAT) | |||
| F103-6 (CANH) - F25-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher | Navigation receiver assembly*1 |
| F103-16 (CANL) - F25-16 (BAT) | |||
| F103-6 (CANH) - F25-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher | Radio and display receiver assembly*2 |
| F103-16 (CANL) - F25-16 (BAT) | |||
| F103-8 (CANH) - F25-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher | Combination meter assembly |
| F103-18 (CANL) - F25-16 (BAT) |
*1: for Navigation Receiver Type
*2: for Radio and Display Type
| Result | Proceed to |
|---|---|
| OK | A |
| NG (No. 3 CAN junction connector main line) | B |
| NG (ECU or sensor bus line) | C |
| NG (DLC3 branch line) | D |
A
B
C
D
Reconnect all wire harness connectors.
Disconnect the ECU or sensor connected to the CAN bus line that is shorted to +B.
If the ECU or sensor has multiple connectors, disconnect the connector that includes the CAN bus lines. To determine the ECU or sensor that is connected to the shorted bus line, refer to Terminals of ECU.
Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>TERMINALS OF ECU
| *1 | DLC3 |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F25-6 (CANH) - F25-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| F25-14 (CANL) - F25-16 (BAT) |
If the resistance changes to 6 kΩ or higher when the connector is disconnected from the ECU or sensor, there may be a short in the ECU or sensor.
| Result |
|---|
| OK |
| NG |
OK
NG