Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM › 2013.12–2016.11
RM3160E _57 Power Source / Network _019704 NETWORKING _0095663 CAN COMMUNICATION SYSTEM J

NETWORKING  CAN COMMUNICATION SYSTEM  Navigation Receiver Assembly Communication Stop Mode  


DESCRIPTION

Detection Item Symptom Trouble Area
Navigation Receiver Assembly Communication Stop Mode Either condition is met:
·

"Display and Navigation (AVN1)" is not displayed on the CAN Bus Check screen of the GTS

Click here(Click here)

·

Communication system DTCs (DTCs that start with U) that correspond to "Navigation Receiver Assembly Communication Stop Mode" in "DTC Combination Table" are output

Click here(Click here)


·

Navigation receiver assembly branch line or connector

·

Power source circuit of navigation receiver assembly

·

Navigation receiver assembly ground circuit

·

Navigation receiver assembly



WIRING DIAGRAM

C295748
1.76,1.146 2.104,0.219 2.104,0.219 2.219,0.219 false 5.281,1.146 5.625,0.219 5.625,0.219 5.74,0.219 false 0.063,0.042 3,0.281 2.938,0.24 12 false V Bus (for RHD): 4.698,0.396 5.313,0.594 0.615,0.198 10 false DLC3 2.292,0.125 3.521,0.792 1.229,0.667 10 false No. 3 CAN Junction Connector 5.813,0.125 7.042,0.792 1.229,0.667 10 false No. 4 CAN Junction Connector 0.729,2.021 1.5,2.219 0.771,0.198 10 false 120 Ω 6.146,2.021 6.917,2.219 0.771,0.198 10 false 120 Ω 0.677,2.646 1.135,2.844 0.458,0.198 10 false ECM 5.771,2.656 6.958,3.208 1.188,0.552 10 false Combination Meter Assembly 0.531,3.969 2.365,4.167 1.833,0.198 10 false Trouble Area 1.448,5.125 5.427,5.323 3.979,0.198 10 false : CAN Main Bus Line (CANH) 1.448,5.417 5.427,5.615 3.979,0.198 10 false : CAN Main Bus Line (CANL) 4.417,5.125 6.24,5.385 1.823,0.26 10 false : CAN Branch Line (CANH) 4.417,5.406 6.115,5.615 1.698,0.208 10 false : CAN Branch Line (CANL) 1.813,3.531 2.583,3.729 0.771,0.198 10 false RADIO 1.729,3.969 2.677,4.281 0.948,0.313 10 false ECU-ACC 1.76,4.417 2.729,4.656 0.969,0.24 10 false IG1 NO. 3 3.406,3.375 3.865,3.573 0.458,0.198 10 false +B1 3.708,3.354 4.323,3.552 0.615,0.198 10 false CANH 4.177,3.354 4.792,3.552 0.615,0.198 10 false CANL 3.417,3.833 4.031,4.031 0.615,0.198 10 false ACC1 3.438,4.26 3.75,4.458 0.313,0.198 10 false IG 3.167,3.188 3.323,3.385 0.156,0.198 10 false 4 3.167,3.625 3.344,3.969 0.177,0.344 10 false 3 3.167,4.073 3.323,4.271 0.156,0.198 10 false 1 3.052,3.375 3.74,3.604 0.688,0.229 10 false F114 3.052,3.823 3.76,4.104 0.708,0.281 10 false F114 3.052,4.26 3.667,4.49 0.615,0.229 10 false F116 4.885,3.708 5.385,3.99 0.5,0.281 10 false F114 3.771,3.167 4.51,3.417 0.74,0.25 10 false F116 4.167,3.167 4.771,3.365 0.604,0.198 10 false F116 4.438,3.708 5.052,3.906 0.615,0.198 10 false GND1 5,3.5 5.156,3.698 0.156,0.198 10 false 7 3.792,2.958 3.948,3.156 0.156,0.198 10 false 9 4.354,2.958 4.667,3.156 0.313,0.198 10 false 10 3.323,4.479 5.521,4.896 2.198,0.417 10 false Navigation Receiver Assembly

CAUTION / NOTICE / HINT

NOTICE:
·

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key, switches or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING

·

After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

·

DTC check procedure: Turn the ignition switch to ON and wait at least 31 seconds.

·

After the repair, perform the CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM

·

Inspect the fuses for circuits related to this system before performing the following procedure.



HINT:
·

Operating the ignition switch, any other switches or a door triggers related ECU and sensor communication on the CAN. This communication will cause the resistance value to change.

·

Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.



PROCEDURE

1.CHECK FOR OPEN IN CAN BUS LINES (NAVIGATION RECEIVER ASSEMBLY BRANCH LINE)
a.

Disconnect the cable from the negative (-) battery terminal.


b.
C287273C17
0.229,1.063 0.656,1.313 0.427,0.25 1.885,1.135 1.875,0.417 1.875,0.417 1.615,0.417 true 2.01,1.135 1.99,0.396 1.99,0.396 2.24,0.396 true 0.073,0.052 0.385,0.25 0.313,0.198 10 false *a 2.292,0.302 2.906,0.5 0.615,0.198 10 false CANL 1.188,0.313 1.802,0.51 0.615,0.198 10 false CANH 0.292,1.094 0.875,1.385 0.583,0.292 10 false F116
*a Front view of wire harness connector
(to Navigation Receiver Assembly)


Disconnect the F116 navigation receiver assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F116-9 (CANH) - F116-10 (CANL) Cable disconnected from negative (-) battery terminal 54 to 69 Ω



Result:
Result
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)

NG

REPAIR OR REPLACE CAN BRANCH LINE OR CONNECTOR (NAVIGATION RECEIVER ASSEMBLY)

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)
a.
C287274C18
1.438,0.208 1.885,0.5 0.448,0.292 1.135,1.99 1.396,1.99 1.396,1.99 1.552,1.625 true 0.125,0.146 0.438,0.344 0.313,0.198 10 false *a 1.51,0.25 2.031,0.51 0.521,0.26 10 false F114 0.74,1.896 1.188,2.073 0.448,0.177 10 false GND1
*a Front view of wire harness connector
(to Navigation Receiver Assembly)


Disconnect the F114 Navigation receiver assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F114-7 (GND1) - Body ground Cable disconnected from negative (-) battery terminal Below 1 Ω



c.

Reconnect the cable to the negative (-) battery terminal.


d.
C290810C20
1.479,0.25 1.927,0.583 0.448,0.333 1.49,2.281 1.938,2.615 0.448,0.333 2.063,1.375 2.365,0.667 2.365,0.667 2.49,0.667 true 2.302,1.385 2.5,0.927 2.5,0.927 2.615,0.927 true 0.958,3.417 0.823,2.823 0.823,2.823 0.708,2.823 true 0.063,0.083 0.375,0.281 0.313,0.198 10 false *a 1.563,0.313 2.229,0.521 0.667,0.208 10 false F114 1.573,2.344 2.031,2.542 0.458,0.198 10 false F116 2.552,0.573 3.167,0.771 0.615,0.198 10 false ACC1 2.677,0.823 3.135,1.021 0.458,0.198 10 false +B1 0.51,2.729 0.823,2.927 0.313,0.198 10 false IG
*a Front view of wire harness connector
(to Navigation Receiver Assembly)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
F114-3 (ACC1) - Body ground Ignition switch ACC 11 to 14 V
F114-4 (+B1) - Body ground Always 11 to 14 V
F116-1 (IG) - Body ground Ignition switch ON 11 to 14 V



Result:
Result
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)